DEMON ELECTRIC REBEL Manuel utilisateur
Rebel
Installation Manual
Scan to watch
assembly video
OWNER’S MANUAL
Table of contents
First of all, we would like to thank you for choosing the REBEL electric bike.
We warmly welcome you to our Demon Electric family. We wish you enjoy the numerous kilometers and
happy moments with your new bike.
After the initial shipment we have made many improvements and modifications for the REBEL including:
•
•
•
•
•
Suspended seat post - Takes the shock out of the big bumps, without the cost or complexity of suspension.
Adjustable handlebar stem- Provides up to 1 1/2” of rise and reach adjustment, for fully customizable
riding position.
Upgraded Shimano derailleur- Rigid cast aluminum construction gives smoother, more precise shifting.
New gearing, with taller top gear for relaxed touring, plus a lower low gear for tight, technical riding.
Demon Electric E-Bikes can be upgraded with additional accessories, such as water bottle holders, phone
mounts, etc.
ASSEMBLY INSTRUCTIONS ......................................................................................3
INSTALL KICKSTAND .....................................................................................................4
INSTALL FENDER AND HEADLIGHT.........................................................................4
INSTALL FRONT WHEEL ..............................................................................................5
INSTALL HANDLEBAR ...................................................................................................6
INSTALL PEDALS..............................................................................................................7
INSTALL SEAT....................................................................................................................8
CONNECT CONNECTORS............................................................................................8
REMOVING BATTERY......................................................................................................9
FOLDING INSTRUCTIONS ............................................................................................10
BATTERY CHARGING .....................................................................................................12
BATTERY CHARGING TIPS...........................................................................................12
OPERATION.........................................................................................................................12
DISPLAY................................................................................................................................13
FEATURES...........................................................................................................................13
TFT SCREEN INSTRUCTIONS....................................................................................14
ERROR CODE DEFINE ...................................................................................................21
WARNINGS AND SAFETY.............................................................................................22
BELOW ARE THE GUIDELINES FOR THE INITIAL
BATTERY CHARGING PROCESS:
• Before using the e-bike for the first time, we strongly recommend that you conduct a preliminary battery
check-up and perform a full charge for optimal performance.
• To charge the battery, before riding connect the e-bike to the charger and allow the battery to reach full
capacity. According to the manufacturer’s instructions, the initial charge typically takes between 48 to 72
hours prior to your first ride.
• During the charging process, keep an eye on the LED indicator or display on your battery charger. This will
give you insights into the charging progression. If you encounter any problems, don’t hesitate to reach out to
the manufacturer for assistance.
• After the battery has been fully charged, it’s recommended to take your e-bike out for a test ride. Pay at-
tention to its performance, including the speed, range, and power-assistance levels. Any significant discrep-
ancies might imply that the battery capacity is compromised and needs further attention.
• Even when the e-bike is not being used frequently, it’s crucial to regularly charge and discharge the bat-
tery. This practice helps to prevent battery degradation during periods of storage.
2
Rebel Manual |
IMPORTANT
Electric Bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage,
or failure of the bicycle or system and all other losses or damages to themselves and others and to any
property arising as a result of using the bicycle.
As with all mechanical components, the bicycle is subjected to wear and high stresses. Different materials
and components may react to wear or stress fatigue in different ways.
If the design life of a component has been exceeded, it may suddenly fail possibly causing injuries to the
rider. Any form of crack, scratches or change of coloring in highly stressed areas indicate that the life of the
component has been reached and it should be replaced.
Please do not hesitate to contact us. If any problems may occur, please email us at
customersuppor[email protected] for any customer service solutions such as replacement parts, technical
information, and any other issues.
All new E-Bike purchases come with a 2-year warranty, the warranty card must be filled in and
registered in order to qualify for warranty.
For any other commercial or general inquires please contact Demon Powersports at 905 881 9510 or
DO NOT DISASSEMBLE, MODIFY OR
REPLACE ELECTRICAL PARTS.
PLEASE NOTE: THIS MANUAL IS NOT INTENDED
AS A DETAILED USER, SERVICE, REPAIR OR
MAINTENANCE MANUAL. PLEASE SEEK
ASSISTANCE FROM A QUALIFIED TECHNICIAN FOR
SERVICE, REPAIRS OR MAINTENANCE.
3
Rebel Manual |
ASSEMBLY INSTRUCTIONS
Your bike has been pre-assembled and requires only a few simple steps to get it ready for you to ride:
Remove the outside carton after cutting the nylon bands. Remove all the inside cardboard protection and
bubble wrap. Carefully remove your bike from the carton and gently rest it in place. Be careful not to cut
any wires when cutting the zip ties.
Remove brake pad holders when installing, avoid squeezing the brakes when removing the pad holder.
Ensure the following pieces are included in the package. If there are any missing parts, please contact
Demon for help replacing missing pieces.
iv) Pedals
i) Bike
v) Charger
ii) Front Wheel iii) Axle
vi) Assembly Tools
vii) Key for Battery viii) Kickstand ix) Seat
10 mm
15 mm
8 mm
13 mm
Wrench
Set
Screw
Driver
Allen Key
Set
3 mm
4 mm
5 mm
6 mm
2 mm
4
Rebel Manual |
INSTALL KICKSTAND
Install kickstand with the 5mm Allen key.
Ensure kickstand is behind the bracket on the left side of the bike during installation.
Bracket on left
side of the bike. Turn bolts clock-wise to tighten.
INSTALL FENDER AND HEADLIGHT
Install the headlight to the front of the fork, and install the fender to the back of the fork with the provided
bolt and washer, tighten with the 5mm Allen key.
3 mm
4 mm
5 mm
6 mm
2 mm
3 mm
4 mm
5 mm
6 mm
2 mm
5
Rebel Manual |
Install the fender sides to the bottom of the front fork with the provided bolt and washer, tighten with the
5mm Allen key.
3 mm
4 mm
5 mm
6 mm
2 mm
INSTALL FRONT WHEEL
Install the front wheel on the front fork, make sure to align the brake disk with the brake caliper, Avoid
squeezing brakes and ensure the brake disc is not rubbing against the wheel.
Fasten the wheel hub using the quick release handle.
Ensure brake disk and
brake caliper are aligned.
Quick release handle on the
caliper side of the wheel.
6
Rebel Manual |
INSTALL HANDLEBAR
Attach clasp to the bottom of the handlebar.
Insert screw into the hole on the clasp, and tighten with the 2mm Allen key.
Align holes on the clasp and
steering bar.
7
Rebel Manual |
INSTALL PEDALS
Using the 15mm wrench provided in the toolkit, attach, and tighten the pedals. PLEASE NOTE – The pedals
are marked “L” for Left and “R” for Right.
L R
The left pedal is attached by turning it counter clockwise and the right pedal is tightened by turning it clock-
wise. Make sure the pedals are tightly attached to the crank arms to prevent stripping.
(See picture below)
15 mm
8
Rebel Manual |
INSTALL SEAT
Make sure the seat is tight enough so that you cannot twist it out of alignment. Pull the seat clamp handle
away from the seat post and slide the seat up or down to adjust it. Move the clamp handle inward toward
the seat post so it is held tight by the clamp.
CONNECT CONNECTORS
Connect the connectors near handle bar, make sure arrows are pointing towards each other when
connecting. Locate the battery key near handle bar and cut the key from zip tie.
Be sure the minimum insertion marks do not go past the top of the seat clamp and are not visible.
Table des matières
Autres manuels DEMON ELECTRIC Vélo
DEMON ELECTRIC
DEMON ELECTRIC PILOT Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC TRONIO Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC OUTLAW Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC 6IX Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC THUNDERBOLT SL Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC PHANTOM Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC ESCAPE Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC ARGO Manuel utilisateur
DEMON ELECTRIC
DEMON ELECTRIC BLACKTAIL Manuel utilisateur
