Dell PowerConnect 8024F Manuel utilisateur
April 2012
SISfeedback@Dell.com
Rapid EqualLogic Configuration Series
Configuration Introduction
Implementation Guide
Switch: PowerConnect 8024F (Dual Switch LAG setting)
Array: PS6010/6510
Host: Windows
THIS IMPLEMENTATION GUIDE IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN
TYPOGRAPHICAL ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS,
WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND.
© 2011 Dell Inc. All rights reserved. Reproduction of this material in any manner whatsoever without
the express written permission of Dell Inc. is strictly forbidden. For more information, contact Dell.
Dell, the DELL logo, and the DELL badge, PowerConnect™, EqualLogic™, PowerEdge™ and
PowerVault™ are trademarks of Dell Inc. Broadcom® is a registered trademark of Broadcom
Corporation. Intel® is a registered trademark of Intel Corporation in the U.S. and other countries.
Microsoft®, Windows®, Windows Server®, and Active Directory® are either trademarks or registered
trademarks of Microsoft Corporation in the United States and/or other countries.
1Introduction
1.1 Document use
Keyboard keys are shown in brackets with the actual key bolded.
Example: [Enter]
Commands that are to be typed are bolded and shown after the appropriate prompt.
Example:
console>enable
1.2 Intended audience
System or Storage administrators with experience deploying Windows servers, storage systems, and
Ethernet networking. If you are unsure about completing the installation, Dell support is available and
ready to assist you.
1.3 List of references
•TR1050 – Monitoring Your PS Series SAN with SAN HeadQuarters
https://support.equallogic.com/WorkArea/DownloadAsset.aspx?id=8749
Note: A login is required to access the EqualLogic support site. If you do
not have a login, go to support.equallogic.com and register.
•
SAN HQ User Guide,
available for download on www.equallogic.com
•
PS-series Group Administration
online help
http://psonlinehelp.equallogic.com/v5.1/groupmanager.htm
2Prerequisites
2.1 Equipment
2.1.1.1 Serial cable
•A null-modem DB9 serial cable (included with the array)
•A switch serial console management cable (included with the switch)
2.2 Software
•Latest network adapter device driver update (support.dell.com)
•Latest Host Integration Tools (HIT) kit installation package (support.equallogic.com)
•Latest SAN HeadQuarters installation package (support.equallogic.com)
Note: A login is required to access the EqualLogic support site.
2.3 Configuration settings
2.3.1 Host/OS
This document assumes that you have already installed Windows 2008 R2 with Service Pack 1 or later
and have applied the latest critical security updates available through Windows Update.
2.3.2 Switch
This document assumes that your PowerConnect 8024F switches are at firmware version 4.1.0.19 or
later. To get the latest update, visit http://support.dell.com. Installation instructions are provided as
part of the download. The switch user manual can also be downloaded for reference.
2.3.3 Array
This document assumes that your storage arrays are at array controller firmware version 5.1.1-H2 or
later. To get the latest update, visit http://support.equallogic.com. Update instructions and release
notes are available with the latest downloads.
2.4 Configuration information
Your iSCSI SAN configuration requires several static IP addresses. Complete this form and have it
available for reference during the configuration.
IP addresses needed for configuration:
Host iSCSI
Initiator
Host #1 Host #2 Host #3 Host #4
Port 1
Port 2
Array Target
Array #1
Array #2
Array #3
Port 1
Port 2
Management
(Out-of-Band)
Array Group
Management IP
(Out-of-Band)
Array Group
Management IP
(In-Band)
Out-of-Band
Switch
Management Port
Switch admin password: _________________________
Array Group admin password: __________________________*
Array Group membership password: __________________________*
*These may be the same password – see the PS-series Group Administration guide for more
information.
http://psonlinehelp.equallogic.com/v5.1/groupmanager.htm
2.5 Connectivity Diagrams
Use the appropriate diagram and following point to point table when cabling the SAN.
PowerConnect 8024F and PS6010 configuration
PowerConnect 8024F and PS6510 configuration
PowerConnect 8024F connections with the PS6010 or PS6510:
Switch 1
Port To
Switch 2
Port To
1 Server 1, port 1 1 Server 1, port 2
2 Server 2, port 1 2 Server 2, port 2
3 Server 3, port 1 3 Server 3, port 2
4 Server 4, port 1 4 Server 4, port 2
Array 3 15 Controller 0, port 0 15 Controller 0, port 1
16 Controller 1, port 1 16 Controller 1, port 0
Array 2 17 Controller 0, port 0 17 Controller 0, port 1
18 Controller 1, port 1 18 Controller 1, port 0
Array 1 19 Controller 0, port 0 19 Controller 0, port 1
20 Controller 1, port 1 20 Controller 1, port 0
Table des matières
Autres manuels Dell Changer
Dell
Dell EMC PowerSwitch S4200-ON Series Manuel utilisateur
Dell
Dell C Series Manuel utilisateur
Dell
Dell PowerConnect 3424 Manuel utilisateur
Dell
Dell PowerConnect J-EX4200 Instructions d'installation
Dell
Dell PowerConnect 6024 Manuel utilisateur
Dell
Dell PowerSwitch E3200-ON Series Manuel utilisateur
Dell
Dell Brocade Adapters Manuel utilisateur
Dell
Dell Force10 Z9000 Manuel utilisateur
Dell
Dell S4048T Manuel utilisateur
Dell
Dell PowerConnect 3400 Series Manuel utilisateur
Dell
Dell PowerEdge 2321DS Manuel utilisateur
Dell
Dell EMC PowerSwitch Z9432F-ON Manuel utilisateur
Dell
Dell PowerConnect 2016 Manuel utilisateur
Dell
Dell Force10 Z9000 Manuel utilisateur
Dell
Dell PowerConnect 6024 Manuel utilisateur
Dell
Dell S4810-ON Manuel utilisateur
Dell
Dell PowerConnect 8024 Manuel utilisateur
Dell
Dell Networking 7048 Mode d’emploi
Dell
Dell PowerConnect 2708 Manuel utilisateur
Dell
Dell PowerConnect 2216 Manuel utilisateur
