Dell N1108T-ON Manuel utilisateur

Dell Networking

N1108T-ON/N1108P-ON/

N1124T-ON/N1124P-ON/

N1148T-ON/N1148P-ON

Switches

Getting Started Guide

Regulatory Models: E17W and E18W

Notes, Cautions, and Warnings

NOTE: A NOTE indicates important information that helps you make better use of

your switch.

CAUTION: A CAUTION indicates either potential damage to hardware or loss of

data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

Lithium battery caution:

• There is a danger of explosion if a battery is incorrectly replaced. Replace

only with the same or equivalent type. Dispose batteries of according to

the manufacturer's instructions.

• Disposing a battery into fire, a hot oven, mechanically crushing, or cutting

it can result in an explosion.

• Leaving a battery in an extremely hot environment can result in leakage of

flammable liquid, gas, or an explosion.

• If a battery is subjected to extremely low air pressure, it may result in

leakage of flammable liquid, gas, or an explosion.

• The device can only be used in a fixed location such as a lab or a machine

room. When you install the device, ensure that the protective earthing

connection of the socket-outlet is verified by a skilled person.

___________________

international copyright and intellectual property laws. Dell and the Dell logo are trademarks of Dell

Inc. in the United States and/or other jurisdictions. All other marks and names mentioned herein may

be trademarks of their respective companies.

Regulatory Models: E17W and E18W

May 2017 P/N NTHM9 Rev. A00

Contents 3

Contents

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . 5

N1100-ON Series Hardware Overview . . . . . . . . . . 5

Power Consumption for N1100-ON Series PoE Switches 5

Ventilation System . . . . . . . . . . . . . . . . . . 6

N1100-ON Series Model Summary . . . . . . . . . . . . 6

2 N1108T-ON/N1108P-ON Installation . . . . . 7

Rack Mounting an N1108T-ON/N1108P-ON Switch . . . . 7

Installing in a Rack . . . . . . . . . . . . . . . . . . 7

3 N1124T-ON/N1124P-ON/N1148T-ON/ N1148P-ON

Installation . . . . . . . . . . . . . . . . . . . . . . . . 9

Rack Mounting an N1124T-ON/N1124P-ON/ N1148T-ON/ N1148P-ON

Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing in a Rack . . . . . . . . . . . . . . . . . . 9

Wall Installation for N1108T-ON and N1108P-ON. . . . 10

Installing as a Free-standing Switch . . . . . . . . 11

Stacking Multiple N1124T-ON/N1124P-ON/ N1148T-ON/ N1148P-ON

Switches . . . . . . . . . . . . . . . . . . . . . . . . . 12

4Contents

4 Starting and Configuring the

N1100-ON Series Switch . . . . . . . . . . . . . 13

Connecting an N1100-ON Series Switch to a Terminal . 14

Connecting an N1100-ON Series Switch to a Power Source 15

AC and DC Power Connection . . . . . . . . . . . 15

Booting the N1100-ON Series Switch . . . . . . . . . . 16

Performing the N1100-ON Series Initial Configuration . 17

Enabling Remote Management . . . . . . . . . . . 17

Initial Configuration Procedure . . . . . . . . . . . 18

Example Session . . . . . . . . . . . . . . . . . . 19

Dell Easy Setup Wizard Console Example . . . . . 20

Next Steps . . . . . . . . . . . . . . . . . . . . . 24

5 NOM Information (Mexico Only) . . . . . . 26

Getting Started Guide 5

Introduction

This document provides basic information about the Dell Networking

N1100-ON Series switches, including how to install a switch and perform the

initial configuration. For information about how to configure and monitor

switch features, refer to the User Configuration Guide, which is available on

the Dell Support website at dell.com/support. See the Support website for

the latest updates on documentation and firmware.

NOTE: Switch administrators are strongly advised to maintain Dell Networking

switches on the latest version of the Dell Networking Operating System (DNOS).

Dell Networking continually improves the features and functions of DNOS based on

feedback from you, the customer. For critical infrastructure, pre-staging of the new

release into a non-critical portion of the network is recommended to verify network

configuration and operation with the new DNOS version.

N1100-ON Series Hardware Overview

This section contains information about device characteristics and modular

hardware configurations for the Dell Networking N1100-ON Series switch.

Power Consumption for N1100-ON Series PoE Switches

Table 1-1 describes the power consumption for N1100-ON Series PoE

switches. The PoE power budget is 60W for the N1108P-ON, 185W for the

N1124P-ON, and 370W for the N1148P-ON.

Table 1-1. Power Consumption for N1100-ON Series PoE Switches

Model Input Voltage Power Supply

Configuration

Maximum

Steady Current

Consumption (A)

Maximum

Steady

Power (W)

N1108P-ON 100V/60Hz Main PSU 0.95A 88.64W

110V/60Hz Main PSU 0.87A 88.43W

120V/60Hz Main PSU 0.80A 88.22W

220V/50Hz Main PSU 0.49A 89.28W

240V/50Hz Main PSU 0.45A 89.70W

6Getting Started Guide

Ventilation System

One fan cools the N1108T-ON/N1108P-ON switches, and two fans cool the

N1024T-ON/N1024P-ON/N1048T-ON/N1048P-ON switches. The fans are

not field replaceable.

N1100-ON Series Model Summary

Table 1-2. N1100-ON Series Switch Regulatory Numbers

N1124P-ON 100V/60Hz Main PSU 2.66A 260.66W

110V/60Hz Main PSU 2.38A 257.95W

120V/60Hz Main PSU 2.16A 256.27W

220V/50Hz Main PSU 1.18A 250.52W

240V/50Hz Main PSU 1.10A 251.25W

N1148P-ON 100V/60Hz Main PSU 4.78A 476.03W

110V/60Hz Main PSU 4.32A 472.64W

120V/60Hz Main PSU 3.95A 470.58W

220V/50Hz Main PSU 2.14A 459.37W

240V/50Hz Main PSU 1.97A 459.06W

Marketing

Model Name

(MMN)

Description Power Supply

Unit (PSU)

Regulatory

Model Number

(RMN)

Regulatory

Type Number

(RTN)

N1108T-ON 10x1G/2x1G SFP Ports DPS-24GP E17W E17W001

N1108P-ON 10x1G/2x1G SFP/2xPoE+ Ports DPS-80AP/

DPS-24GP

E17W E17W001

N1124T-ON 24x1G/4x10G SFP+ Ports DPS-40AP E18W E18W001

N1124P-ON 24x1G/4x10G SFP+/6xPoE+ Ports EDPS-250BF E18W E18W001

N1148T-ON 48x1G/4x10G SFP+ Ports DPS-60AP E18W E18W002

N1148P-ON 48x1G/4x10G SFP+/12xPoE+ Port YM-2501D E18W E18W002

Model Input Voltage Power Supply

Configuration

Maximum

Steady Current

Consumption (A)

Maximum

Steady

Power (W)

Getting Started Guide 7

N1108T-ON/N1108P-ON Installation

Rack Mounting an N1108T-ON/N1108P-ON Switch

WARNING: Read the safety information in the

Safety and Regulatory Information

as well as the safety information for other switches that connect to or support the

switch.

The AC power connector is on the rear panel of the switch.

Installing in a Rack

WARNING: Do not use rack mounting kits to suspend the switch from under a

table or desk, or attach it to a wall.

CAUTION: Disconnect all cables from the switch before continuing. Remove all

self-adhesive pads from the underside of the switch, if they have been attached.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

Secure the N1108T-ON/N1108P-ON switch in either the Dell Rack Mount

Kit as shown in Figure 1-1 or the Dell Tandem Tray Kit as shown in

Figure 1-2.

Figure 1-1. Dell Rack Mount Kit

8Getting Started Guide

Figure 1-2. Dell Tandem Tray Kit

Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack

mounting holes on the kit line up to the mounting holes in the rack.

Secure the kit to the rack with either the rack bolts or cage nuts and cage-

nut bolts with washers (depending on the kind of rack you have). Fasten

the bolts on the bottom before fastening the bolts on the top.

Getting Started Guide 9

N1124T-ON/N1124P-ON/N1148T-ON/

N1148P-ON Installation

Rack Mounting an N1124T-ON/N1124P-ON/

N1148T-ON/ N1148P-ON Switch

WARNING: Read the safety information in the

Safety and Regulatory Information

as well as the safety information for other switches that connect to or support the

switch.

The AC power connector is on the rear panel of the switch.

Installing in a Rack

WARNING: Do not use rack mounting kits to suspend the switch from under a

table or desk, or attach it to a wall.

CAUTION: Disconnect all cables from the switch before continuing. Remove all

self-adhesive pads from the underside of the switch, if they have been attached.

CAUTION: When mounting multiple switches into a rack, mount the switches

from the bottom up.

Place the supplied rack-mounting bracket on one side of the switch,

ensuring that the mounting holes on the switch line up to the mounting

holes in the rack-mounting bracket. Figure 1-3 illustrates where to mount

the brackets.

Figure 1-3. Attaching the Brackets

10 Getting Started Guide

Insert the supplied bolts into the rack-mounting holes and tighten with a

screwdriver.

Repeat the process for the rack-mounting bracket on the other side of the

switch.

Insert the switch into the 48.26 cm (19 inch) rack, ensuring that the rack-

mounting holes on the bracket line up with the mounting holes in the

rack.

Secure the bracket to the rack with either the rack bolts or cage nuts and

cage-nut bolts with washers (depending on the kind of rack you have).

Fasten the bolts on the bottom before fastening the bolts on the top.

CAUTION: Make sure that the supplied rack bolts fit the pre-threaded holes in the

rack.

NOTE: Make sure that the ventilation holes are not obstructed.

Wall Installation for N1108T-ON and N1108P-ON

To mount the switch on a wall:

Make sure that the mounting location meets the following requirements:

• The surface of the wall must be capable of supporting the switch.

• Allow at least two inches (5.1 cm) space on the sides for proper

ventilation and five inches (12.7 cm) at the back for power cable

clearance.

• The location must be ventilated to prevent heat buildup.

Place the supplied wall-mounting bracket on one side of the switch,

verifying that the mounting holes on the switch line up to the mounting

holes on the wall-mounting bracket.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dell Changer

Dell

Dell X1000 Series Manuel utilisateur

Dell

Dell OptiPlex XE3 Tower Manuel utilisateur

Dell

Dell S4810-ON Manuel utilisateur

Dell

Dell PowerConnect 3400 Series Manuel utilisateur

Dell

Dell PowerConnect B-RX Manuel utilisateur

Dell

Dell Force10 Z9000 Manuel utilisateur

Dell

Dell PowerConnect PC7024 Guide de référence rapide

Dell

Dell PowerConnect M8428-k Manuel utilisateur

Dell

Dell PowerConnect 3424 Manuel utilisateur

Dell

Dell DF10MXL Manuel utilisateur

Dell

Dell POWERCONNECT 5524 Manuel utilisateur

Dell

Dell PowerConnect 2808 Manuel utilisateur

Dell

Dell Console Switch Manuel utilisateur

Dell

Dell PowerConnect W-Series FIPS Manuel du propriétaire

Dell

Dell SMA 200 Mode d’emploi

Dell

Dell PowerVault 51F Manuel utilisateur

Dell

Dell Networking Z9500 Manuel utilisateur

Dell

Dell PowerVault 51F Mode d’emploi

Dell

Dell EMC N2200-ON Series Manuel utilisateur

Dell

Dell PowerConnect 5224 Manuel utilisateur

Dell

Dell PowerConnect M8428-k Manuel utilisateur

Dell

Dell PowerConnect 8024 Manuel utilisateur

Dell

Dell PowerConnect 3548 Manuel utilisateur

Dell

Dell Force10 MXL Blade Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur