Dell S3100 Series Manuel utilisateur

Dell Networking S3100 Series

Getting Started Guide

Regulatory Model: S3100

Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dell PowerConnect

S3124 o cerca il tuo prodotto tra le migliori offerte di Switch

Notes, cautions, and warnings

NOTE: A NOTE indicates important information that helps you make better

use of your computer.

CAUTION: A CAUTION indicates either potential damage to hardware or loss

of data and tells you how to avoid the problem.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

international copyright and intellectual property laws. Dell™and the Dell logo are trademarks

of Dell Inc. in the United States and/or other jurisdictions. All other marks and names

mentioned herein may be trademarks of their respective companies.

2016 - 04

Rev. A01

About this Guide

This document is intended as a Getting Started Guide to get new systems up

and running and ready for configuration.

For more details about S3100 series installation and software configuration,

see the following information, available on the Dell Networking Support

website (http://www.dell.com/support).

• The Dell Networking S3100 Series Installation Guide describes installation

and replacement procedures.

• The Dell Configuration Guide for the S3100 Series describes software

configuration.

• The Dell Command Line Reference Guide for the S3100 Series provides

command line interface (CLI) information.

• The Dell Networking S3100 Series Release Notes provide information

about upgrading the S3100 series.

About this Guide 3

Installation

This information describes installation of a S3100 series system. Dell

Networking recommends completing the installation procedures in the order

presented here.

Operation and Safety Considerations

Before installing the switch, review these operation and safety guidelines.

Review these guidelines for switch installation:

• You have enough clearance to the front of the switch so you can read the

light emitting diodes (LEDs).

• The AC power cord reaches from the power outlet to the power supply

unit (PSU) side connector.

• The switch is rack-mounted before you power it up.

• Cabling is away from sources of electrical noise, such as radios, power

lines, and fluorescent lighting. Ensure that the cabling is safely away from

other devices that might damage the cables. If needed, allow one rack unit

(RU) space between devices to provide room for cabling.

• Airflow around the switch and through the vents is unrestricted.

• Temperature around the unit does not exceed 113°F (45°C). If the switch is

in a closed or multi-rack assembly, the temperature might be higher than

normal room temperature.

• Humidity around the switch does not exceed 95 percent.

• Altitude at the installation site is below 10,000 feet.

• The switch is installed in an environment as free as possible from dust and

foreign conductive material (such as metal flakes from construction

activities). Cooling mechanisms, such as fans and blowers in the switch,

can draw dust and other particles causing contaminant buildup inside the

chassis, which can result in system malfunction.

Review these guidelines for rack mounting:

• Rack mounting — You may either place the switch on a rack shelf or

mount the switch directly into a 19" wide, EIA-310-E- compliant rack.

4Installation

• Rack loading — Overloading or uneven loading of racks may result in shelf

or rack failure, causing damage to the equipment and possible personal

injury. Stabilize racks in a permanent location before loading begins.

Mount the components starting at the bottom of the rack, then work to

the top. Do not exceed your rack load rating.

• Power considerations — Connect only to the power source specified on

the unit. When you install multiple electrical components in a rack, ensure

that the total component power ratings do not exceed the circuit

capabilities. Overloaded power sources and extension cords present fire

and shock hazards.

• Elevated ambient temperature — If you install the equipment in a closed

rack assembly, the operating temperature of the rack environment may be

greater than the room ambient temperature. The acceptable ambient

temperature ranges are listed in the S3100 Series Technical Specifications

section under Environmental Parameters.

• Reduced air flow — Install the equipment in the rack so that you do not

compromise the amount of airflow required for safe operation of the

switch. For proper ventilation, position the chassis in an equipment rack

(or cabinet) with a minimum of 5 inches (12.7 cm) of clearance around

exhaust vents.

• Reverse air flow — To ensure cool air intake and to avoid hot air blow out

from the I/O side, ensure that you have the necessary clearance.

• Reliable earthing — Maintain reliable earthing of rack-mounted

equipment. Pay particular attention to the supply connections other than

the direct connections to the branch circuit; for example, use of power

strips.

• Do not mount the equipment with the PSU side facing in a downward

position.

NOTE: Always handle the system and its components with care. Avoid

dropping the chassis or their field replaceable units.

CAUTION: Always wear an electrostatic discharge (ESD)-preventive

wrist or heel ground strap when handling a system and its

components. As with all electrical devices of this type, take all

necessary safety precautions to prevent injury when installing this

system. ESD damage can occur if components are mishandled.

CAUTION: Only trained and qualified personnel should install this

equipment. Read this guide before installing and powering up the

system.

WARNING: This is a condensed reference. Read the safety instructions

in your Safety, Environmental, and Regulatory information booklet

before you begin.

Installation 5

Unpacking a S3100 Series Switch

To unpack your switch, follow these steps.

NOTE: Before unpacking the switch, inspect the container and

immediately report any evidence of damage.

When unpacking each S3100 series switch, make sure that the following

items are included:

• One S3100 series switch.

• One RJ-45 to DB-9 female cable.

• One Dell ReadyRails™ kit for rack installation, two mounting brackets,

bolts, and cage nuts.

• One set of self-adhesive rubber pads for free-standing installation (four

pads are included).

• One PSU.

•Getting Started Guide.

•Safety and Regulatory Information.

•Warranty and Support Information.

•Software License Agreement.

1. Place the container on a clean, flat surface and cut all straps securing the

container.

2. Open the container or remove the container top.

3. Carefully remove the switch from the container and place it on a secure

and clean surface.

4. Remove all packing material.

5. Inspect the product and accessories for damage.

Installing the Dell ReadyRails System

The ReadyRails rack mounting system is provided to easily configure your

rack so that you can install your switch.

The Dell ReadyRails™ system is provided for 1U front-rack and two-post

installations. The ReadyRails system includes two separately packaged rail

assemblies and two rails that are shipped attached to the sides of the switch.

Install the ReadyRails system using the 1U tool-less method or one of three

possible 1U tooled methods (two-post flush mount, two-post center mount,

or four-post threaded).

6Installation

CAUTION: Do not use the mounted ReadyRails as a shelf or a

workplace.

NOTE: The illustrations in this document are not intended to represent a

specific switch.

1U Tool-less Configuration

To install the Dell ReadyRails system using the 1U tool-less configuration,

follow these steps.

1. With the ReadyRails flange ears facing outward, place one rail between

the left and right vertical posts. Align and seat the back flange rail pegs in

the back vertical post flange. To see how the pegs appear in both the

square and unthreaded round holes, see item 1 in the following figure.

2. Align and seat the front flange pegs in the holes on the front side of the

vertical post.

3. Repeat this procedure for the second rail.

4. To remove each rail, pull on the latch release button on each flange ear

and unseat each rail.

Figure 1. 1U Tool-less Configuration

Two-Post Flush-Mount Configuration

To install the Dell ReadyRails system using the two-post flush-mount

configuration, follow these steps.

1. For this configuration, remove the castings from the front side of each

ReadyRails assembly. See item 1 in the following figure. Use a Torx driver

to remove the two screws from each front flange ear (on the switch side

Installation 7

of the rail) and remove each casting. Retain the castings for future rack

requirements. It is not necessary to remove the rear flange castings.

2. Attach one rail to the front post flange with two user-supplied screws.

See item 2 in the following figure.

3. Slide the plunger bracket forward against the vertical post and secure the

plunger bracket to the post flange with two user-supplied screws. See

item 3 in the following figure.

4. Repeat this procedure for the second rail.

Figure 2. Two-Post Flush-Mount Configuration

1. Removing the castings.

2. Attaching rail to the front post flange.

3. Securing the plunger bracket to the post flange.

8Installation

Two-Post Center-Mount Configuration

To install the Dell ReadyRails system using the two-post center-mount

configuration, follow these steps.

1. Slide the plunger bracket rearward until it clicks into place and secure the

bracket to the front post flange with two user-supplied screws. See item

1 in the following figure.

2. Slide the back bracket towards the post and secure it to the post flange

with two user-supplied screws. See items 2 and 3 of the following figure.

3. Repeat this procedure for the second rail.

Figure 3. Two-Post Center-Mount Configuration

1. Securing the bracket to the front post flange.

2. Securing the back bracket.

Installation 9

Four-Post Threaded Configuration

To install the Dell ReadyRails system using the four-post threaded

configuration, follow these steps.

1. Remove the flange ear castings from each end of the ReadyRails

assemblies. Use a Torx driver to remove the two screws from each flange

ear and remove each casting. See item 1 of the following figure. Retain

the castings for future rack requirements.

2. For each rail, attach the front and rear flanges to the post flanges with

two user-supplied screws at each end. See item 2 of the following figure.

Figure 4. Four-Post Threaded Configuration

10 Installation

Autres manuels pour S3100 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dell Stockage

Dell

Dell MD1400-16TB Manuel utilisateur

Dell

Dell PowerVault NX3500 Manuel utilisateur

Dell

Dell PowerVault RD1000 Manuel utilisateur

Dell

Dell PowerVault TL2000 Manuel utilisateur

Dell

Dell PowerVault MD3000i Guide de démarrage rapide

Dell

Dell PowerVault 110T DLT4000 Manuel utilisateur

Dell

Dell PowerVault MD3260i Series Guide de référence rapide

Dell

Dell PowerVault X5MJV Manuel utilisateur

Dell

Dell Equallogic PS6010e Guide d'installation

Dell

Dell PowerVault 100T DDS4 Manuel utilisateur

Dell

Dell PowerVault DL2200 CommVault Manuel utilisateur

Dell

Dell PowerVault 200S Guide rapide

Dell

Dell PowerVault 701N Manuel de l'opérateur

Dell

Dell SC5020 Manuel utilisateur

Dell

Dell PowerVault ML6000 Manuel utilisateur

Dell

Dell PowerVault 132T Manuel d'installation et d'exploitation

Dell

Dell DX6012S Manuel utilisateur

Dell

Dell FS7500 Manuel utilisateur

Dell

Dell PowerVault JU892 Manuel utilisateur

Dell

Dell NX3230 Manuel utilisateur

Dell

Dell PowerVault 51F Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

Dell

Dell PowerVault 110T LTO-2-L Manuel utilisateur

Dell

Dell PowerVault TL2000 Comment utiliser

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur