Dell PowerEdge 400SC Manuel
www.dell.com | support.dell.com
Dell™ Systems
Processor Upgrade
Installation Guide
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury,
or death.
____________________
Information in this document is subject to change without notice.
© 2003 Dell Computer Corporation. All rights reserved.
Reproductioninanymannerwhatsoever without the written permissionofDellComputerCorporationisstrictlyforbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names
other than its own.
June 2003 P/N Y1336 Rev. A00
Processor Upgrade Installation Guide 1-1
You can upgrade your processor to take advantage of future options in speed and
functionality. Each processor and its associated cache memory are contained in a pin-grid
array (PGA) package that is installed in a ZIF socket on the system board.
Replacing the Processor
CAUTION: See your System Information Guide for complete information about
safety precautions, working inside the computer, and protecting against
electrostatic discharge.
CAUTION: The processor and heat sink can get very hot during normal operation.
Ensure that they have had sufficient time to cool before you touch them.
1Turn off the system and attached peripherals, and disconnect the system from the
electrical outlet.
2Press the power button to ground the system board.
3If you have installed a padlock through the padlock ring on the back panel, remove
the padlock.
4Lay the system on its side as shown in Figure 1-1.
NOTICE: Ensure that sufficient space exists to accommodate the open cover—at least 30 cm
(1 ft) of desktop space.
5Open the system by pushing the buttons on both ends and lifting the cover open.
See Figure 1-1.
1-2 Processor Upgrade Installation Guide
www.dell.com | support.dell.com
Figure 1-1. Opening the System
6Rotate the processor cooling shroud up to access the processor and heat sink.
See Figure 1-2.
buttons (2)
(one on each side
of the system)
padlock ring
security cable slot
Processor Upgrade Installation Guide 1-3
Figure 1-2. Rotating the Processor Cooling Shroud
7Remove the processor heat sink. See Figure 1-3.
aRemove one retention module clip by pressing the tab on the clip and lifting
the retention module clip up.
bWhile pulling the retention module tab out, lift the heat sink away from
the processor.
cooling shroud
1-4 Processor Upgrade Installation Guide
www.dell.com | support.dell.com
Figure 1-3. Removing the Heat Sink
8Pull the processor socket release lever straight up until the processor is released.
See Figure 1-4.
Figure 1-4. Removing the Processor
heat sink
retention module clip
retention module tab
cooling pipes
re
l
ease
l
ever
processor
socket
Processor Upgrade Installation Guide 1-5
NOTICE: Be careful not to bend any of the pins when you remove the processor from
the socket. Bending the pins can permanently damage the processor.
9Remove the processor from the socket and leave the release lever in the release
position so that the socket is ready for the new processor.
10 Align pin 1 (the imprinted corner) of the processor and pin 1 of the socket.
See Figure 1-5.
NOTICE: Processor pins are delicate. To avoid damage, ensure that the processor aligns
properly with the socket, and do not use excessive force when you install the processor.
11 Carefully set the processor in the socket and press it down lightly to seat it.
12 Rotate the release lever back toward the system board until it snaps into place,
securing the processor.
Figure 1-5. Installing the Processor
13 Remove the thermal grease protective cover from the heat sink.
NOTICE: If your heat sink has cooling pipes, orient the heat sink so that the cooling pipes are
toward the memory modules to prevent damage to system board components.
release lever
processor
socket
socket pin-1 indicator
processor pin-1 indicator
1-6 Processor Upgrade Installation Guide
www.dell.com | support.dell.com
14 Place one end of the heat sink under the retention module tab on the side opposite
the removed clip, and lower the heat sink onto the processor until the heat sink snaps
securely in the retention module. See Figure 1-3.
15 Replace the retention module clip by pressing in on the tab and lowering that end
of the clip into the retention module. See Figure 1-3.
16 Rotate the processor cooling shroud down. See Figure 1-2.
17 Close the system cover:
aPivot the cover down and into position. See Figure 1-1.
bPress down on the cover to close it.
18 If you are using a padlock to secure your system, install the padlock.
19 Reconnect the system to the electrical outlet, and turn on the system and attached
peripherals.
www.dell.com | support.ap.dell.com/china
Dell™ 系统
处理器升级安装指南
注、注意和警告
注：注表示可以帮助您更好地使用计算机的重要信息。
注意：注意表示可能会损坏硬件或导 数据丢失，并告诉您如何避免此类问题。
警告：警告表示存在可能导致财产损失、人身伤害或死亡的潜在危险。
____________________
本文中的信息如有更改，恕不另行通知。
© 2003 Dell Computer Corporation. 保留所有权利。
未经 Dell Computer Corporation 的书面许可，严禁 任何方式进行复制。
本文中使用的商标： Dell 和Dell 徽标是 Dell Computer Corporation 的商标。
本文述及的其它商标和产品名称是指拥有相应商标和名称的公司或其制造的产品。
Dell Computer Corporation 对其它公司的商标和产品名称不拥有任何专利权。
2003 年6 月P/N Y1336 Rev. A00
Autres manuels pour PowerEdge 400SC
1
Table des matières
Langues :
Autres manuels Dell Serveur
Dell
Dell PowerEdge 4200 Series Manuel utilisateur
Dell
Dell EMC PowerEdge R450 12M1H Manuel
Dell
Dell PowerEdge 6350 Manuel utilisateur
Dell
Dell PowerEdge 4400 Manuel technique
Dell
Dell PowerEdge T710 Mode d’emploi
Dell
Dell PowerEdge C6320 Manuel utilisateur
Dell
Dell 3250 Manuel utilisateur
Dell
Dell PowerEdge R415 Manuel utilisateur
Dell
Dell 5J5D0 Manuel
Dell
Dell POWEREDGE R710 Manuel utilisateur
Dell
Dell PowerEdge M1000e Manuel utilisateur
Dell
Dell PowerEdge F0VN9 Manuel utilisateur
Dell
Dell PowerEdge NX182 Manuel utilisateur
Dell
Dell POWEREDGE T300 Manuel utilisateur
Dell
Dell PowerApp 110 Manuel utilisateur
Dell
Dell PowerEdge T130 Manuel utilisateur
Dell
Dell PowerEdge R210 II Manuel utilisateur
Dell
Dell PowerEdge 2800 Mode d’emploi
Dell
Dell Dimension 2200 Manuel utilisateur
Dell
Dell 3250 Manuel utilisateur
