Dell PowerEdge 2800 Manuel

www.dell.com | support.dell.com

Dell™ Systems

Installing the SCSI Backplane

Daughter Card

安装 SCSI 背板子卡

Installation de la carte fille

de fond de panier SCSI

Installieren der SCSI-Rückwandplatinen-

Tochterkarte

SCSI バックプレーンドータ

カードの取り付け

SCSI 후면판 보조 카드 설치

Instalación de la tarjeta secundaria

de plano posterior SCSI

www.dell.com | support.dell.com

Dell™ Systems

Installing the SCSI Backplane

Daughter Card

Notes, Notices, and Cautions

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid

the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

____________________

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.

Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

July 2004 P/N F6589 Rev. A00

Installing the SCSI Backplane Daughter Card 1-3

This document provides information about how to configure the split SCSI backplane in your

Dell™ PowerEdge™ 2800 or 2850 system by installing a backplane daughter card. In a split

backplane configuration, the hard-drives are arranged in two separate groups of drives.

CAUTION: Only trained service technicians are authorized to remove the system cover and access any

of the components inside the system. See your Product Information Guide for complete information

about safety precautions, working inside the computer, and protecting against electrostatic discharge.

NOTE: See your Installation and Troubleshooting Guide for detailed instructions on removing

or replacing components.

Installing the SCSI Backplane Daughter Card

in a PowerEdge 2800 System

Remove the bezel (if applicable).

Unpack the SCSI backplane daughter card kit.

Turn off the system, including any attached peripherals, and disconnect the system from

the electrical outlet.

Open the system.

Slide the drive tray to the maintenance position.

Use a #2 Phillips screwdriver to loosen the captive screw that secures the drive tray

release handle to the chassis.

Rotate the drive tray release lever toward the front of the system.

Grasp both sides of the front panel and slide the drive tray forwards until the tray is in

the maintenance position.

Hold the daughter card by its edges with the card connector facing the SCSI backplane board.

Insert the card connector into the daughter card connector on the SCSI backplane board.

Ensure that the standoffs on the daughter card are fully seated into the SCSI backplane

board. See Figure 1-1.

1-4 Installing the SCSI Backplane Daughter Card

www.dell.com | support.dell.com

Figure 1-1. Installing the SCSI Daughter Card

To use the optional integrated ROMB controller in a split 2 x 4 backplane configuration:

Connect channel A on the riser card to SCSIA on the SCSI backplane. This channel

controls the boot drive (drive 0) and drives 1, 2, and 3.

Connect SCSI channel B on the riser card to connector SCSIB on the SCSI backplane.

This channel controls drives 4, 5, 8, and 9.

To use an optional RAID controller card in a split 2 x 4 backplane configuration:

Connect SCSI channel A (channel 0) on the controller card to connector SCSIA on

the SCSI backplane. This channel controls the boot drive (drive 0) and drives 1, 2, and 3.

Connect SCSI channel B (channel 1) on the controller card to connector SCSIB on

the SCSI backplane. This channel controls drives 4, 5, 8, and 9.

Slide the drive tray back into the operating position.

Grasp both sides of the front panel and slide the drive tray backwards until the tray is

in the operating position.

Rotate the drive tray release lever toward the back of the system.

Use a #2 Phillips screwdriver to tighten the captive screw that secures the drive tray

release handle to the chassis.

Close the system.

Reconnect the system to its electrical outlet and turn the system on, including any attached

peripherals.

Enter System Setup to ensure that the RAID or SCSI controller card is configured correctly.

See your system’s

User’s Guide

for more information.

Replace the bezel (if applicable).

SCSI daughter card

SCSI backplane board

standoffs (2)

Installing the SCSI Backplane Daughter Card 1-5

Installing the SCSI Backplane Daughter Card

in a PowerEdge 2850 System

Unpack the SCSI backplane board daughter card kit.

Turn off the system, including any attached peripherals, and disconnect the system from

the electrical outlet.

Remove the bezel (if applicable).

Open the system.

Grasp the plastic tab on the back of the control panel cable and pull the cable connector away

from the backplane connector. See Figure 1-2.

NOTE: If you pull on the control panel cable harness, you may damage the harness.

The SCSI backplane daughter card connector and card guide are located in the compartment

below the control panel cable.

Figure 1-2. Installing a SCSI Backplane Daughter Card

SCSI daughter card

SCSI backplane

retention lever

SCSI daughter card guide

retention peg

on card

control panel cable

SCSI daughter card

backplane connector

control-panel connector on backplane

1-6 Installing the SCSI Backplane Daughter Card

www.dell.com | support.dell.com

The daughter card fits between the sides of the card guide. To install the daughter card in

the card guide and to connect it to the backplane connector:

Ensure that the retention lever is in the open position.

Hold the daughter card by its edges with the card connector facing the SCSI backplane

and the retention peg facing the retention lever. See Figure 1-2.

Lower the card into the card guide.

Close the retention lever to slide the daughter card into the SCSI backplane connector

and lock the card into place. See Figure 1-2.

Rotate the drive bay retraction bar toward the front of the system. See Figure 1-3.

Figure 1-3. Drive Bay Retraction Bar

Reconnect the control panel cable to its backplane connector. See Figure 1-2.

To use the optional integrated ROMB controller in a split backplane configuration:

Connect channel A on the riser card to SCSIA on the SCSI backplane. This channel

controls the boot drive (drive 0) and drive 1.

Connect SCSI channel B on the riser card to connector SCSIB on the SCSI backplane.

This channel controls drives 2 through 5.

drive bay retraction bar

Installing the SCSI Backplane Daughter Card 1-7

To use the optional RAID controller card in a split backplane configuration:

Connect SCSI channel A (channel 0) on the controller card to connector SCSIA on

the SCSI backplane. This channel controls the boot drive (drive 0) and drive 1.

Connect SCSI channel B (channel 1) on the controller card to connector SCSIB on

the SCSI backplane. This channel controls drives 2 through 5.

NOTE: If a cable is connected to the SCSIB backplane connector, the SCSI backplane daughter

card must be installed to activate the 2/4 split backplane configuration. Otherwise, the system will

display an error message.

Rotate the drive bay retraction bar toward the back of the system.

Close the system.

Enter System Setup to ensure that the RAID or SCSI controller card is configured correctly.

See your system’s

User’s Guide

for more information.

Replace the bezel (if applicable).

1-8 Installing the SCSI Backplane Daughter Card

www.dell.com | support.dell.com

Autres manuels pour PowerEdge 2800

Table des matières

Langues :

Autres manuels Dell Serveur

Dell

Dell PowerEdge T320 Guide de démarrage rapide

Dell

Dell PowerEdge R530xd Manuel utilisateur

Dell

Dell EMC PowerEdge XR11 Manuel

Dell

Dell 810 Manuel utilisateur

Dell

Dell PowerEdge 1800 Manuel

Dell

Dell PowerEdge M610x Guide de démarrage rapide

Dell

Dell PowerEdge 800 Manuel technique

Dell

Dell PowerEdge R510 Manuel technique

Dell

Dell POWEREDGE T300 Manuel utilisateur

Dell

Dell poweredge VRTX Manuel utilisateur

Dell

Dell PowerEdge R7625 Manuel

Dell

Dell POWEREDGE E11S Manuel utilisateur

Dell

Dell PowerEdge M420 Manuel d'utilisation

Dell

Dell 6100 Manuel utilisateur

Dell

Dell PowerEdge PDU Managed LED Manuel utilisateur

Dell

Dell PowerEdge R210 II Guide de démarrage rapide

Dell

Dell 6100 Manuel utilisateur

Dell

Dell PowerEdge FC430 Manuel utilisateur

Dell

Dell PowerEdge E07S Series Manuel utilisateur

Dell

Dell PowerEdge C2100 Manuel utilisateur

Dell

Dell EMC PowerEdge R450 D K 0 Series Manuel

Dell

Dell PowerEdge T620 Manuel utilisateur

Dell

Dell PowerEdge FC630 Manuel utilisateur

Dell

Dell PowerEdge 1800 Mode d’emploi

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur