Dell PowerEdge 1750 Mode d’emploi
www.dell.com | support.dell.com
Dell™ Systems
Installing a ROMB Card
安装 ROMB 卡
Installation de la carte ROMB
Installieren einer ROMB-Karte
ROMB カードの取り付け
ROMB 카드 설치
Instalación de una tarjeta ROMB
M0170fc0.fm Page 1 Tuesday, February 25, 2003 11:56 AM
M0170fc0.fm Page 2 Tuesday, February 25, 2003 11:56 AM
www.dell.com | support.dell.com
Dell™ Systems
Installing a ROMB Card
M0170ebk0.book Page 1 Thursday, February 27, 2003 11:00 AM
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you
how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury,
or death.
____________________
Information in this document is subject to change without notice.
© 2003 Dell Computer Corporation. All rights reserved.
ReproductioninanymannerwhatsoeverwithoutthewrittenpermissionofDellComputerCorporationisstrictlyforbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Computer Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and
names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names
other than its own.
March 2003 P/N M0170 Rev. A00
M0170ebk0.book Page 2 Thursday, February 27, 2003 11:00 AM
Installing a ROMB Card 1-1
This document contains information about installing a RAID on mother board (ROMB)
card.
Installing a ROMB Card
CAUTION: Only trained service technicians are authorized to remove the system
cover and access any of the components inside the system. See your System
Information Guide for complete information about safety precautions, working
inside the computer, and protecting against electrostatic discharge.
NOTICE: To avoid possible data loss, back up all data on the hard drives before changing the
mode of operation of the integrated SCSI controller from SCSI to RAID.
1Remove the front bezel (if applicable).
2Turn off the system, including any attached peripherals, and disconnect the system
from the electrical outlet.
3Remove the optional security screw (if applicable). See Figure 1-1.
4Press the latch on the system front panel and lift the left cover.
5Lift the right cover.
Figure 1-1. Opening the System Covers
latch
optional security screw
right cover
left cover
M0170ebk0.book Page 1 Thursday, February 27, 2003 11:00 AM
1-2 Installing a ROMB Card
www.dell.com | support.dell.com
6Locate the ROMB card connector on the system board. See Figure 1-2.
7If a PCI card is installed over the ROMB card connector, remove it. See your
Installation and Troubleshooting Guide for instructions.
8Position the ROMB card with the notch in its plastic cover facing the redundant power
supply bay, and align the edges of the card with the four plastic standoffs on the
system board. See Figure 1-2.
9Press down on the ROMB card cover until the four plastic standoffs snap over the edge
of the card. See Figure 1-2.
Figure 1-2. Installing the ROMB Card and Backup Battery
ROMB card
plastic standoffs (4)
notch
backup battery
RAID_BAT connector
standoffs (2)
ROMB card connector
M0170ebk0.book Page 2 Thursday, February 27, 2003 11:00 AM
Installing a ROMB Card 1-3
10 Install the ROMB backup battery:
aRemove the SCSI backplane board. See "Removing the SCSI Backplane Board."
bPosition the battery board as shown in Figure 1-2, and press it down into the two
standoffs until it snaps into place.
cPlug the battery cable into the RAID BAT connector on the system board.
dInstall the SCSI backplane board. See "Installing the SCSI Backplane Board."
11 If you removed a PCI card in step 7, replace it. See your Installation and
Troubleshooting Guide for instructions.
12 Close the system covers.
When closing the covers, close the right (larger) cover first and then close the left
cover. Press firmly on the left cover to snap the securing latch into place.
13 Install the optional security screw (if applicable). See Figure 1-1.
14 Install the front bezel (if applicable).
15 Reconnect the system and peripherals to their electrical outlets, and turn them on.
16 Enter the System Setup program and verify that the setting for the SCSI controller has
changed to reflect the presence of the RAID hardware. See "Using the System Setup
Program" in your User's Guide.
17 Configure the RAID card and logical drives. See the ROMB card documentation for
more information.
Removing the SCSI Backplane Board
1Pull each hard-drive carrier partially out of its slot, approximately 2.5 cm (1 inch).
2Disconnect the diskette-drive interface cable from the FLOPPY connector on the
backplane board. See Figure 1-3.
3Disconnect the CD drive interface cable from the CD_ROM connector on the
backplane board. See Figure 1-3.
4Press the release latch in toward the backplane board and use the handle to pull the
board out of its connector and up out of the chassis.
M0170ebk0.book Page 3 Thursday, February 27, 2003 11:00 AM
1-4 Installing a ROMB Card
www.dell.com | support.dell.com
Figure 1-3. SCSI Backplane Board
Installing the SCSI Backplane Board
1Insert the SCSI backplane board into the chassis:
aFit the metal tabs (one tab at each end of the backplane) into the slots in the
chassis wall and lower the backplane into the chassis, ensuring that the CD and
diskette drive interface cables are not caught under the backplane.
bPress down firmly over the handle to seat the backplane in its connector.
2Pivot the release latch out into the securing slot in the chassis.
3Connect the CD drive interface cable to the CD_ROM connector on the backplane
board. See Figure 1-3.
CD drive interface
connector (CD_ROM)
diskette drive interface connector
(FLOPPY)
handle
release latch
tabs (2)
M0170ebk0.book Page 4 Thursday, February 27, 2003 11:00 AM
Installing a ROMB Card 1-5
4Connect the diskette-drive interface cable to the FLOPPY connector on the backplane
board. See Figure 1-3.
5Press all installed hard drives firmly back into the SCSI connectors on the backplane.
M0170ebk0.book Page 5 Thursday, February 27, 2003 11:00 AM
1-6 Installing a ROMB Card
www.dell.com | support.dell.com
M0170ebk0.book Page 6 Thursday, February 27, 2003 11:00 AM
Autres manuels pour PowerEdge 1750
7
Table des matières
Langues :
Autres manuels Dell Serveur
Dell
Dell poweredge VRTX Manuel utilisateur
Dell
Dell PowerEdge M420 Manuel utilisateur
Dell
Dell OptiPlex 3000 Manuel utilisateur
Dell
Dell PowerApp 110 Manuel utilisateur
Dell
Dell PowerEdge 2300 Manuel utilisateur
Dell
Dell External OEMR R310 Guide de démarrage rapide
Dell
Dell PowerEdge XE8640 Manuel
Dell
Dell EMC VxFlex Ready Node 14G Manuel utilisateur
Dell
Dell PowerConnect M8428-k Manuel technique
Dell
Dell XC730xd Manuel utilisateur
Dell
Dell PowerEdge XR4000w Manuel
Dell
Dell POWEREDGE T300 Manuel utilisateur
Dell
Dell PowerEdge 2400 Manuel utilisateur
Dell
Dell PowerEdge R630 Manuel utilisateur
Dell
Dell PowerEdge NX182 Manuel utilisateur
Dell
Dell PowerEdge R930 Manuel utilisateur
Dell
Dell PowerEdge SC420 Manuel technique
Dell
Dell PowerEdge 1550 Manuel utilisateur
Dell
Dell E33S001 Manuel utilisateur
Dell
Dell PowerEdge R715 Manuel utilisateur
