Dell PowerApp .cache 100 Manuel technique

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Dell Serveur

Dell

Dell PowerEdge R6615 Manuel

Dell

Dell PowerEdge 350 Manuel

Dell

Dell XC720xd Manuel utilisateur

Dell

Dell PowerEdge SC1435 Manuel utilisateur

Dell

Dell PowerEdge 750 Manuel utilisateur

Dell

Dell ECS EX Series Instructions d'installation

Dell

Dell PowerEdge PDU Managed LED Manuel utilisateur

Dell

Dell EMC VxFlex Ready Node 14G Manuel

Dell

Dell PowerEdge M630p Manuel utilisateur

Dell

Dell PowerEdge R910 Manuel

Dell

Dell EMC PowerEdge T640 D24XR Manuel

Dell

Dell PowerEdge M630 Manuel utilisateur

Dell

Dell PowerEdge 4600 Manuel utilisateur

Dell

Dell EMC PowerEdge R640 Manuel

Dell

Dell PowerEdge M610x Guide de démarrage rapide

Dell

Dell POWEREDGE R710 Manuel utilisateur

Dell

Dell PowerEdge R610 Manuel utilisateur

Dell

Dell PowerEdge R510 Manuel utilisateur

Dell

Dell PowerEdge HR675 Manuel utilisateur

Dell

Dell PowerEdge R620 Manuel utilisateur

Dell

Dell EMC PowerEdge R640 Manuel

Dell

Dell PowerEdge 7150 Manuel utilisateur

Dell

Dell Wyse P25 Manuel utilisateur

Dell

Dell PowerEdge 2550 Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP

HP AlphaServer ES47 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur

Planet

Planet NAS-7410 Manuel utilisateur

Lenovo

Lenovo ThinkSystem SR635 V3 Manuel utilisateur

Fujitsu

Fujitsu PRIMERGY BX900 Manuel utilisateur

Asus

Asus RS700DA-E6 PS4 Manuel utilisateur















This document updates information contained in your Dell PowerApp 100 appliance

documentation.

If you replace the appliance’s microprocessor and heat sink assembly, you must remove the fan

attached to the top of the replacement microprocessor and heat sink assembly. (For details on

removing the microprocessor, see “Microprocessor” in your Service Manual.)

To install the replacement microprocessor and heat sink assembly, perform the following steps:

1. If applicable, remove the fan from the heat sink in the replacement kit.

The fan will not be used. To remove the fan, gently squeeze the sides of two adjacent cor-

ners on the fan.

2. Gently place the replacement microprocessor into the zero insertion force (ZIF) socket so

that the processor pins mate exactly with the ZIF socket.

Make sure that pin 1 of the microprocessor is oriented correctly in the socket.





3. Swing the ZIF socket arm down until it snaps into the socket tab after the microprocessor is

in place.

4. At the base of the heat sink, remove and discard the protective cover over the thermal

grease by pulling the cover’s tab.

5. Place the heat sink on the microprocessor.

Be careful not to touch the surfaces coated with thermal grease.

The bevelled surface on the heat sink covers the part of the ZIF socket that is not covered by

the microprocessor.

6. Drop the heat sink clip into the heat sink's center groove with the end of the clip that has

two slots facing the front of the ZIF socket.

7. Gently hold the heat sink in place as you press down on the shorter end of the heat sink

clip (the end that has a single slot) until that end snaps into its tab on the back of the ZIF

socket (see Figure 1).



8. Use your thumb to press down on the front end of the heat sink clip (the end that has

two slots) until it snaps into the socket tab.

9. Replace the cover, install the power cord, and reboot the computer.

____________________

Information in this document is subject to change without notice.

© 2000 Dell Computer Corporation. All rights reserved. Printed in the U.S.A.

Trademarks used in this text: Dell, the DELL E COM logo, and PowerApp are trademarks of Dell Computer Corporation. Other

trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their

products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.

heat sink clip

microprocessor and

heat sink assembly

tabs on ZIF socket (2)

ZIF socket

ZIF socket

release lever