Deif BRW-2 Manuel utilisateur

BRW-2 replacement for

BRW-1

Bridge wing indicator

Quick guide

4189350057C

1. Mounting the unit

This is only relevant for the replacement of existing BRW-1 products.

The three PG21 type cable glands on the bottom of the unit are suitable for cable gauge 13 to 18 mm.

The BRW-2 is protected from ESD (static electricity). This means that no special ESD protection measures are required

when mounting the unit.

QUICK START GUIDE 4189350057C UK Page 2 of 4

2. Wiring of the unit

NOTICE

Warranty is void if the warranty seal is removed or broken

Powering up

The pointer position is random until the power supply is connected. On power-up, the pointer will move randomly for the

first couple of seconds. This is normal operation. Also on power-up, the amber LED in the lower right corner of the scale

area will flash once or twice and then turn off.

Wiring

Remove the potentiometer panel using a standard 4 mm Allan key to access the terminals. Exercise caution when removing

the panel to avoid damaging the gasket.

BRW-2 uses a 24 V DC supply for power and illumination.

•BRW-1 uses either an AC or DC supply. This means that the polarity on the existing BRW-1 installation may be reversed.

•BRW-2 must be connected with the correct polarity.

Terminal pos. Supply

5 -

6 + 24 V DC

B EARTH.

This terminal must be connected to the ship's hull.

The potentiometer marked “MAX. ADJ”, located between the two connectors, can be used to make fine adjustments to the

pointer deflection to match the indicator's scaling with the existing installation.

QUICK START GUIDE 4189350057C UK Page 3 of 4

3. General

Accuracy

This is a special version of the BRW-2 with additional circuits to simulate BRW-1 operation. This means it does not meet the

standard specified accuracy of Class 0.5.

BRW-2 Replacement meets accuracy Class 1.0.

Future replacement

For future replacement, it is not necessary to replace the entire BRW-2 indicator. You may only need to replace the XL192

indicator part (the top part of the product).

NOTE When replacing the built-in XL 192 indicator, the measuring range is either 0 mA to 1 mA or -1 mA to + 1 mA. See

the type label on the XL 192 indicator.

QUICK START GUIDE 4189350057C UK Page 4 of 4

Autres manuels pour BRW-2

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Deif Instrument de mesure

Deif

Deif MIC-2 MKII Manuel utilisateur

Deif

Deif TRI-2 Manuel utilisateur

Deif

Deif AGC 150 Manuel utilisateur

Deif

Deif MIB 7000 Manuel utilisateur

Deif

Deif WSI Manuel utilisateur

Deif

Deif XDi Series Manuel utilisateur

Deif

Deif Insight Manuel utilisateur

Deif

Deif BRW-2 Manuel utilisateur

Deif

Deif BRW-2 Manuel utilisateur

Deif

Deif DLQA96 Manuel utilisateur

Deif

Deif MIQ96-2 Manuel utilisateur

Deif

Deif ADL-111Q96/xxVDC Series Instructions d'installation

Deif

Deif MIC-2 MKII Instructions d'utilisation et d'entretien

Deif

Deif MIB 8000 Manuel utilisateur

Deif

Deif XL Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur