DeFelsko PosiTector 6000 Manuel utilisateur
Instruction Manual v. 1.0
with PosiTector
6000
probes
Table of Contents
Table of Contents
Introduction .................................................................. 1
Why is Measurement Important? ........................... 2
Golden Rule ........................................................... 2
Quick Start ................................................................... 3
PosiTector App ............................................................. 4
Connect PosiTector App to PosiTector probe ........ 4
User Interface ........................................................ 5
PosiTector SmartLink ................................................... 7
Connect a Probe .................................................... 7
Power-up/Power-down ........................................... 8
Tri-Color LED Button .............................................. 8
PosiTector 6000 probes ............................................... 9
actory Calibration ................................................. 9
Calibration Adjustment ........................................... 10
Certification ............................................................ 10
Calibration, Verification and Adjustment ...................... 10
Menu Operation ........................................................... 12
Memory Menu .............................................................. 13
New Batch .............................................................. 13
Batch Summary View ........................................ 14
Tool Bar .............................................................. 14
Delete/Ignore Reading .................................. 15
Add New Batch .............................................. 15
Add Photo ...................................................... 16
Add Notes ...................................................... 16
Share Batch .................................................. 17
Report ................................................................ 17
Export ................................................................ 17
Batch Readings View ........................................ 18
Batch Chart View ............................................... 18
Open ...................................................................... 19
Close ...................................................................... 19
Delete ..................................................................... 20
Batch Report Configuration ................................... 20
Batch Report .......................................................... 21
Statistics Menu ............................................................. 21
HiLo Alarm ............................................................. 22
HiLo Alarm Limits ................................................... 22
Clear ....................................................................... 22
Cal Settings Menu ....................................................... 23
Zero Calibration Adjustment ................................... 24
1-Point Calibration Adjustment ............................... 25
2-Point Calibration Adjustment ............................... 26
Calibration Memory ................................................ 27
N Lock .................................................................... 28
Lock Current Cal .................................................... 28
View Current Cal .................................................... 28
Reset Current Cal .................................................. 28
Setup Menu ................................................................. 29
SmartLink Info ........................................................ 29
Change Units ......................................................... 29
SmartLink Lock ...................................................... 29
Scan Mode ............................................................. 30
ast Mode .............................................................. 30
Reset (Menu Reset / LED Button Reset) ............... 30
Temperature ................................................................. 31
Troubleshooting ........................................................... 32
Warranty ...................................................................... 33
1
Introduction
Introduction
PosiTector 6000 probes non-destructively measure the thickness of
coatings on metals, quickly and accurately. This instruction manual
specifically covers use with PosiTector SmartLink.
The PosiTector SmartLink and free mobile app allow you to wirelessly
connect a wide selection of PosiTector probes to your smart device.
Take full advantage of your device's keyboard, microphone, camera,
internet data connection, etc. to simplify and enhance your
measurement inspection process.
The PosiTector SmartLink measurement solution consists of a
PosiTector App, PosiTector SmartLink device and compatible
PosiTector probe.
In addition to the PosiTector 6000, compatible probes include the
PosiTector SPG/RTR-H (surfa e profile) and DPM (environmental
onditions).
2
Golden Rule
Measure your uncoated part first!
This quick zero-check determines if a Calibration Adjustment
(pg 23) is needed for your substrate.
Next, lay the included plastic shims onto the bare uncoated
surface and measure them individually to ensure the PosiTector
6000 measures a known thickness within tolerance.
Why is Measurement Important?
Dry film thickness (D T) is arguably the single most important
measurement made during the application and inspection of
protective coatings. Coatings are designed to perform their
intended function when applied within a tight D T range as
specified by the manufacturer. Correct thickness ensures optimum
product performance. Even the most basic specification will
require D T to be measured.
Many physical and appearance properties of the finished coating
can be directly affected by the film thickness including the color,
gloss, surface profile, adhesion, flexibility, impact resistance, and
hardness of the coating. The fit of pieces assembled after coating
can be affected when film thickness isn’t within tolerance.
Regular film thickness measurement helps control material costs,
manage application efficiency, maintain finish quality and ensure
compliance with contract specifications. Paint manufacturers
recommend target ranges to achieve optimum performance
characteristics and clients expect these parameters to be met.
Precisely measuring finish thickness has other benefits, too.
Whether to meet International Organization for Standardization
(ISO), quality, or customer requirements for process control,
companies need to verify coating quality to avoid wasting money
reworking product.
3
Quick Start
Quick Start
The PosiTector SmartLink powers-up when the LED button is
pressed. To preserve battery life, the PosiTector SmartLink
powers-down after 5 minutes of no activity. Alternatively, press and
hold the LED button until it turns red and shuts off (approximately
5 seconds).
All probe settings and alibration adjustments (pg 23) are retained
within the PosiTector SmartLink, stored measurement data is
retained within the smart device (cell phone, tablet).
Wirelessly connect the PosiTector probe to the smart device using
the PosiTector App.
Measure
Remove the protective plastic cap (if supplied) from probe.1
Place the probe LAT on the surface to be measured. 2
HOLD STEADY. When a valid measurement is calculated,
the LED button flashes green and the measurement is
displayed on the PosiTector App.
Lift probe AT LEAST 2 INCHES (5 cm) from the surface3
between readings - OR - leave probe on the surface in the
same location for continuous readings.
This continuous reading feature is intended to allow careful probe
placement on small or odd-shaped surfaces. Ignore all readings
taken before the probe is properly placed.
If Memory (pg 13) is ON while continuous readings are being
taken, only the last value on the display (when the probe is lifted)
is stored into memory. S an Mode (pg 30) stores ALL readings into
memory.
To ensure best measurement accuracy, see Calibration,
Verifi ation and Adjustment (pg 10).
4
PosiTector App
PosiTector App
The PosiTector App connects a PosiTector SmartLink to your smart
device enabling you to use PosiTector 6000, DPM, SPG or RTR-H
probes on your device without the need for a conventional gage body.
Screen fonts, brightness and displayed language are inherited from
your smart device settings. Currently, the PosiTector App has language
support for English, Spanish, rench, German, Chinese and Korean.
Screen orientation is fixed to portrait only, rotation to landscape is not
supported.
Stored batch readings, images and notes are all stored in the
PosiTector App (on your smart device). The number of stored batch
readings is only limited by the memory available on your smart device.
If the application is removed or a menu Reset (pg 30) is performed, all
stored measurements and associated data is permanently erased.
Power-up the PosiTector SmartLink and connected 6000 probe1
by pressing the LED button. The button will blink blue.
Select the PosiTector SmartLink App icon on your smart device. 2
Select Continue. A list of available PosiTector probes (listed by3
connected probe type and serial number) will be displayed. Select
the desired PosiTector SmartLink to connect. The LED button on
the PosiTector SmartLink will illuminate solid blue when
successfully connected.
The probe model and serial number is engraved on the backside of the
plastic probe connector (i.e. N 212921).
Wirelessly Connecting the PosiTector App
Wirelessly Connecting the PosiTector App
to a PosiTector
to a PosiTector 6000
6000 probe
probe
5
The user interface was designed to combine the proven simplicity of
PosiTector gages and the advanced functionality of a smart device's
features including touch, swipe, keyboard, camera and more. The
interface will be instantly recognizable to those familiar with PosiTector
instruments.
ser Interface
ser Interface
Main Navigation Bar
The Main Navigation section is dynamic and may change from one
screen to another.
In the example above, Search and Menu navigation options are
available.
Sear h returns back to the list of available PosiTector SmartLink
devices. Menu accesses the Main Menu.
SmartLink Status Bar
Displays information about the connected PosiTector SmartLink and
associated probe.
The example indicates that the PosiTector SmartLink battery status is
full and connected to a PosiTector 6000 N probe (serial number:
212921).
6
Tool Bar
Displays available actions applicable to current operating modes
(i.e. Memory (pg 13), Statisti s (pg 21), HiLo (pg 22), etc.)
Measurement Area
Displays measurement related information. The coating thickness
example on page 5 shows the last measurement (54 microns) on a
ferrous ( ) substrate using calibration adjustment Cal 1. Memory is ON
and measurements are being stored into Batch 6 (B6).
The measurement area will change depending on the connected probe
type and selected modes.
Modes Icons and nits
Displays icons for active modes (such as the disk icon XX for Memory
mode, pg 13), current calibration adjustment type ( X actory), and
measurement units (microns).
Carousel
The carousel is displayed when more than a single view (screen) is
present. The number of dots represent the number of available views.
Swipe your finger horizontally across the screen to switch between
views.
Tip:Some views contain interactive areas. or this reason we
recommend swiping horizontally across the Mode I ons and Units bar.
7
The PosiTector SmartLink acts as a relay between the PosiTector
probe and PosiTector App using wireless Bluetooth Smart
(BLE Bluetooth Low Energy). No pairing required!
Auto-pairing Bluetooth connection works up to 10 m (30 feet) away.
Information specific to currently selected modes (i.e. S an mode
(pg 30), Fast mode (pg 30), etc.) and user calibration adjustments
(specific to each probe) are retained within the PosiTector SmartLink.
This allows for seamless switching between smart devices (phone and
tablet).
Measurement data is not stored within the PosiTector
SmartLink. All measurement data (readings, images, notes) is stored
within the PosiTector App on your smart device.
PosiTector
PosiTector SmartLink
SmartLink
NOTE:
Connect a Probe
To connect a probe, slide the plastic probe connector in the direction
of the arrow (shown above) until it locks in place. Reverse for
detaching the probe.
When powered-up, the PosiTector SmartLink automatically determines
what type of probe is attached and does a self-check. The probe type,
model and serial number are displayed when found within the app's
Sear h screen.
Autres manuels pour PosiTector 6000
7
Table des matières
Autres manuels DeFelsko Instrument de mesure
DeFelsko
DeFelsko PosiTector 200 Manuel utilisateur
DeFelsko
DeFelsko PosiTector SHD Manuel utilisateur
DeFelsko
DeFelsko PosiTector UTG Manuel utilisateur
DeFelsko
DeFelsko PosiTector IRT Manuel utilisateur
DeFelsko
DeFelsko PosiTector DPM Manuel utilisateur
DeFelsko
DeFelsko PosiTector BHI Manuel utilisateur
DeFelsko
DeFelsko PosiTest AIR Manuel utilisateur
DeFelsko
DeFelsko PosiTest HHD Verifier Manuel utilisateur
DeFelsko
DeFelsko PosiTest AT-A Manuel utilisateur
DeFelsko
DeFelsko PosiTector 200 Manuel de service
DeFelsko
DeFelsko PosiTector 6000 Manuel utilisateur
DeFelsko
DeFelsko PosiTector 6000 Manuel de service
DeFelsko
DeFelsko PosiTector BHI Manuel utilisateur
DeFelsko
DeFelsko PosiTest DFT Manuel utilisateur
DeFelsko
DeFelsko PosiTector SHD Standard Manuel utilisateur
DeFelsko
DeFelsko PosiTector PC Manuel utilisateur
DeFelsko
DeFelsko PosiTector RTR 3D Manuel utilisateur
DeFelsko
DeFelsko PosiTector DPM Manuel utilisateur
DeFelsko
DeFelsko PosiTest PC powder Cheker Manuel utilisateur
DeFelsko
DeFelsko PosiTector SPG Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur