decon IN0120 Manuel utilisateur
2020-06-23 1(8)
Assembly Instruction IN0120 Simplex
Attachment IN0120 for mounting Simplex attendant control is designed to be as flexible as
possible. This makes it possible to achieve the desired position as the attachment can be
mounted in several different ways. Consider different options before deciding. The maximum
width between the pipe clamps to be mounted is 510mm.
The attachment also includes a hinge that allows the handle to be folded down when not in
use. This is to reduce the length of the chair in narrow spaces, for example in an elevator.
NOTE! Neither the handle nor the attachment is intended to withstand the entire chair
weight during manual driving. This means that the handle should be folded down and that
the regular handles of the wheelchair should be used in situations when the chair is to be
lifted or driven in demanding environments.
1. Start by getting acquainted with the attachment and go through the different sections
as below.
Max 510mm
1. Screw for locking clamp
2. Levels
3. Klick-lock
4. Screw for adjusting the ball's position, width and length
5. Frictionhinge
6. Screw for locking
7. Extension brackets and screws. Used for mounting on wide chairs.
1
6
4
2
3
5
7
2020-06-23 2(8)
On wider chairs, use the extension brackets including screws. By fitting these it is possible to
mount the attachment on chairs with up to 610mm* between the mounting points.
* Individual deviations may occur depending on how the attachment is mounted.
Note that the ball joint can be mounted
on the top or bottom of the bracket,
in this way, the height of the attachment can be varied.
See the mounting examples below.
2020-06-23 3(8)
2020-06-23 4(8)
With extension brackets.
With extension brackets.
2020-06-23 5(8)
Mounting
1. Mount the equipment on the current chair. Check that the bubble in the spirit level is
centered, this indicates correct angle and is a prerequisite for the control handle to
function satisfactorily.
2. Now it is time to mount the Simplex control handle in the attachment.
a. Start by removing the four M6 nuts and washers.
b. Slide the control cable down through the hole in the plate.
c. Position the handle, mount the four nuts and washers and tighten these.
d. Fix the control cable with cable ties as shown. Check the correct length and
that the cable will not get caught when the handle is folded up / down.
As an option we have IN0121 where the two screws for locking the clamps are replaced with
cam levers. This enables toolless mounting and disassembly which can be advantageous on
foldable wheelchairs etc. IN0121 is ordered separately.
b
d
c
2020-06-23 6(8)
3. Verify that the handle including the folding-down of the handle works and that it does
not interfere with headrest or other parts of the chair in both positions.
Unfolded position
Folded position
2020-06-23 7(8)
Adjustments
The equipment will be ready for use when delivered, below adjustment should only be
performed if there is a special need or if the equipment has been moved to another chair. It
is possible to adjust the friction in the hinge and the locking force of the latch. However,
this should be done with caution. After adjusting, always verify that the click lock locks /
unlocks properly and that the hinge does not go too easily / sluggishly during the up /
down movement.
1. Screw for adjusting the friction in the hinge.
2. Cable tie for fixing the signal cable.
3. Screws for adjusting the locking force. Apply a small quantity Loctite 243 or
equivalent on these screws to avoid loosening. Adjust both sides equally.
4. Apply a small quantity of grease to the contact surfaces of the click-lock after
adjustment, wipe off excess.
2
3
1
4
2020-06-23 8(8)
Om inget annat specifiseras, använd följande åtdragningsmoment.
Unless otherwise specified, use the following tightening torque.
Metriska grovgängor, stål.
Metric coarse threads, steel.
Gänga / Thread
Åtdragningsmoment / Tightening torque
M3
1,2 Nm
M4
3 Nm
M5
6 Nm
M6
10 Nm
M8
25 Nm
M10
50 Nm
M12
85 Nm
Navhylsor.
Hubsleeves.
Gänga / Thread
Åtdragningsmoment / Tightening torque
M16x1
30 Nm
M18x1
40 Nm
Table des matières
Autres manuels decon Accessoires pour appareils photo
