Decon wheel E-move Manuel utilisateur

E-MOVE

Service Manual

Contents

1. Product Overview ……………………………………………………………………… 1

1.1　Product Features …………………………………………………………………… 1

1.2　Variations …………………………………………………………………………… 2

2. Installation Requirements ………………………………………………………… 3

2.1　Strength Requirements ……………………………………………………………… 3

2.2　Structural Requirements …………………………………………………………… 3

2.3　Functional Requirements …………………………………………………………… 5

3. Unit Installation and Removal …………………………………………………… 6

3.1　JWX-2 Components …………………………………………………………………… 7

3.2　Installing the JWX-2 ……………………………………………………………… 8

3.3　Installing and Removing the Wheel Drive Unit Assembly ………………… 12

4. Component Adjustment ……………………………………………………………… 14

4.1　Adjusting the Battery Seat Angle …………………………………………… 14

4.2　Adjusting the Power Switch Location and Angle,

Fitting and Adjusting the Mode Switch, Changing

the Switch Location (Left/Right) and Connecting

the Wiring ………………………………………………………………………… 16

4.3　Adjusting the Position of the Coupler Box

(Coupler for the Left-hand Wheel Drive Unit Assembly) ………………… 30

4.4　Adjusting the Warning Lamp (LED) Direction ……………………………… 31

4.5　Using Offset Washers …………………………………………………………… 32

5. Component Installation, Removal, Disassembly,

Assembly and Adjustment ………………………………………………………… 33

5.1　Removing and Re-installing the Handrim …………………………………… 33

5.2　Removing and Re-installing the Wheel Assembly …………………………… 36

5.3　Removing and Re-installing the Circuit Board …………………………… 38

5.4　Removing and Re-installing the Coupler Box ……………………………… 41

5.5　Removing and Re-installing the L/R Connecting Cable …………………… 45

5.6　Adding and Removing the Springs ……………………………………………… 47

5.7　Copying Setting Data …………………………………………………………… 49

5.8　Calibrating the Handrim Sensor Neutral Position ………………………… 51

6. JW Smart Tune ………………………………………………………………………… 53

7. Warnings ………………………………………………………………………………… 54

7.1　Warnings List ……………………………………………………………………… 54

8. Self-diagnosis ……………………………………………………………………… 56

8.1　Self-diagnosis (Self-diagnosis Function) …………………………………… 56

8.2　Fault Detection Chart …………………………………………………………… 56

9. Inspections and Maintenance …………………………………………………… 59

9.1　Inspection Checklist …………………………………………………………… 59

10. Speci󲥬cations and Other Information ……………………………………… 60

10.1　Speci󲥬cations …………………………………………………………………… 60

10.2　Dimensions and Diagrams ……………………………………………………… 61

10.3　Wiring Diagram …………………………………………………………………… 62

Product Overview

1.1　Product Features

1. Product Overview

Sample E-Move Installa-

① Wheel drive unit assembly with AC servo 󲥭at motor

② Power switch

③ Dedicated battery with built-in microprocessor

　 Choice of nickel-metal hydride or lithium-ion battery

④ Mode switch (option)

④

③

①

②

Product Overview

1.2　Variations

Model E-Move

Product Tire size Note

JWX2-B24E2 24 inch

JWX2-C22E2 22 inch

JWX2-C24E2 24 inch

JWX2-D24E2 24 inch without mounting bracket

JWX2-E24E2 24 inch without mounting bracket

JWX2-F24E2 24 inch

Selectable Part

Hand rims: Stainless steel / Plastic coated

Battery: Nickel-metal hydride / Lithium-ion

Optional Part

Mode switch (Driving mode changing system)

Installation Requirements

（1）Thewheelchairframemustnothaveacamberangle.

（2）Thewheelchairframemustbesufficientlystrong.(Notethatthestrengthofawheelchairframemayde-

clinewithprolongeduse.)

　　Example:

 ・Playordeformationincomponentssuchasrivets,boltfasteningsorcasters.

 ・Componentswithvisiblewearorcorrosion.

2.1　StrengthRequirements

ToinstalltheE-Move,thewheelchairframemustmeetthestrengthrequirementslistedbelow.

Warning

・DonotinstalltheE-Moveonawheelchairframethatdoesnotmeetthestrengthrequirements.

2.2　StructuralRequirements

ToinstalltheE-Move,thewheelchairframemustmeetthestructuralrequirementslistedbelow.

Warning

・DonotinstalltheE-Moveonawheelchairframethatdoesnotmeetthestructuralrequirements.Even

whereitcanbesuccessfullyinstalled,problemsmayariseduringusethatcouldcauseinjuryorac-

cident.

2.2.1　Wheelchairframe

（1）Thediameteroftheaxleholeis18mmor20mm.

（2）Thecontactsurfacesforthenutsaroundtheaxleholemustbe󲥭atandhaveamplesurfacearea.

（3）WhentheE-Moveisinstalled,theremustbenointerference betweentheE-Moveand thewheel-

chairframe.

nImportant

・Ifyouareusingoffsetwasherstoavoidsuchinterference,checkthetwoitemsbelowandinstalluptothree

washersoneachside.

− Thenutseatsarecompletelysecure.

− Thewheelchairbrakeseatsarecompletelysecure.

2.InstallationRequirements

Installation Requirements

2.2.2　Casters

Seven-inchorlargercastersarerecommendedforthefrontcasters.

Withsmall-diametercasters,itisdifficulttogetoverlargebumps.Theshockexperiencedgoingoverbumps

isalsogreaterifthecastersaresmall.

Largediameter

(easytogetoverbumps)

Smalldiameter

(diﬃculttogetoverbumps)

Installation Requirements

2.3　FunctionalRequirements

Warning

・DonotinstalltheE-Moveonawheelchairframethatdoesnotmeetthefunctionalrequirements.Even

whereitcanbesuccessfullyinstalled,problemsmayariseduringusethatcouldcauseinjuryorac-

cident.

ToinstalltheE-Move,thewheelchairframemustmeetthefunctionalrequirementslistedbelow.

（1）Theframemustbeconstructedtoallow22-or24-inchwheelstobeattached.

（2）Thewheelchairisequippedwithaparkingbrakethatcanberelocatedandadjustedtothecor-

rectpositiononthetires.Whenapplied,thebrakemustbecapableofstoppingthewheelchair

withtheE-Moveinstalledona7°forwardorbackwardincline.

（3）WiththeE-Moveinstalled,itmustbepossibletotipthewheelchairforwardandbackbyatleast

20°andtothesidebyatleast15°.

 (Abackwardtippingangleofatleast25°isrecommended.)

Forwardtippingangle Backwardtippingangle Sidetippingangle

Minimum

20°

Minimum

20°

Minimum

15°

（4）Takecaretoensurethatthefunctioningofthewheelchairframeisnotimpairedbytheinstal-

lationoftheE-Move.

 Example:

 ・Movementofmoveablearmsupports,foldingmechanism,parkingbrakeeffectiveness,etc.

Unit Installation and Removal

3. Unit Installation and Removal

Warning

・When cutting cable ties, do not cut on an angle. Always cut off the

surplus as close as possible to the fastener. Cable ties cut to a

pointcouldcauseinjurytothecustomer.

Note

・In locations where the tightening torque is specified, always tighten to the specified torque.

Insufficient tightening torque will cause looseness, while excessive torque could cause dam-

age.

・Installtheunitwiththebatteryremoved.

Unit Installation and Removal

3.1　E-MoveComponents

OWNER’S MANUAL

①

⑦⑨ ⑩

⑪

⑫

⑬

⑭

⑮

⑯

⑰

⑧⑨

②③

⑱

⑲

⑤⑥

④

No. Component Remarks Qty

① Leftwheeldriveunitassembly For22-inchor24-inch(selectable) 1

② Rightwheeldriveunitassembly For22-inchor24-inch(selectable) 1

③ Manualset Owner’sManual,Warranty,GuidelinesforSafeUse,

InstallationManual 1

④ Cableties 10

⑤ Battery Nickel-metalhydrideorlithium-ion(selectable) 1

⑥ Charger Nickel-metalhydrideorlithium-ion(selectable) 1

⑦ Stopperarm Left 1

⑧ Stopperarm Right 1

⑨O-rings Fittedontostopperarms 4

⑩Boss 2

⑪ Washers

Forstopperarmoffset(axlesleeve)

Foraxlesleeveinstallation–35/18.5mmdia.,

3.2mmthick

⑫ Washers Forstopperarmoffset(boss)

28/8.5mmdia.,3.2mmthick 6

⑬ Washers Forplateoffset-18/6.2mmdia.,1.6mmthick 12

⑭Bolts Forstopperarm–M8 2

⑮Bolts Forplatelock–M6 4

⑯ Platelock 2

⑰ Axlesleeve 2

⑱ Nuts Foraxlesleeveinstallation 2

⑲ Bushes Foradjustmentfrom18→20mmdia.axlesleeve 2

*ThecomponentsNo.⑦~No.⑲arenotincludedinthe“withoutmountingbarcket”models.

 See“1.2Variations”.

Unit Installation and Removal

3.2　InstallingtheE-Move

Withtheexceptionofthecabling,theprocedureforinstallingtheE-Moveinamodular-typewheel-

chairisthesame forbothleftandrightsides.Accordingly,themodeldescriptiongivenbelowis

forinstallationontheleftside.Usethesameproceduretoinstallontheright.

　Requiredtools: 4mmand5mmhexagonalwrenches(Allenkeys),24mmsocket,socketwrench,torque

wrench,22mmand24mmspanners

1 Remove the axle sleeve (a) installed

onthewheelchair.

Removetheexistingwheelandaxlesleeve(a)

fromthesidebracket(b)onthewheelchair.

（a）

（b）

2 Installtheaxlesleeve(c).

（1）Installthestopperarm(d)andboss(e)on

thewheelchairsidebracket(b)andtem-

porarilytightenthebolt(f).

（e）

（f）

（d）

（b）

Autres manuels pour e-move

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Decon wheel Fauteuil roulant

Decon wheel

Decon wheel eMove MEM6003-30+ Manuel utilisateur

Decon wheel

Decon wheel MED3152 Manuel utilisateur

Decon wheel

Decon wheel Rehatec Galileo MED3300 Manuel utilisateur

Decon wheel

Decon wheel MED3071 Manuel utilisateur

Decon wheel

Decon wheel MED3030 Manuel utilisateur

Decon wheel

Decon wheel Panthera S2 Manuel utilisateur

Decon wheel

Decon wheel MED3116 Manuel utilisateur

Decon wheel

Decon wheel E-Drive, Etac Prio Manuel utilisateur

Decon wheel

Decon wheel e-move Manuel utilisateur

Decon wheel

Decon wheel Dietz AS Manuel utilisateur

Decon wheel

Decon wheel Levo LCEV MED3125 Manuel utilisateur

Decon wheel

Decon wheel MED3054 Manuel utilisateur

Decon wheel

Decon wheel Mobilex Dolphin Manuel utilisateur

Decon wheel

Decon wheel OlympicHopper Manuel utilisateur

Decon wheel

Decon wheel MEM6145 Manuel utilisateur

Decon wheel

Decon wheel Easywheel Manuel utilisateur

Decon wheel

Decon wheel Helium Manuel utilisateur

Decon wheel

Decon wheel e-move Manuel utilisateur

Decon wheel

Decon wheel Mobilex Dolphin MEM6443P Manuel utilisateur

Decon wheel

Decon wheel Trigo T MED3327 Manuel utilisateur

Decon wheel

Decon wheel MEYRA X3-3.352 Manuel utilisateur

Decon wheel

Decon wheel R82 Kudu Manuel utilisateur

Decon wheel

Decon wheel Roxx2 Manuel utilisateur

Decon wheel

Decon wheel MED3007 Manuel utilisateur

Manuels Fauteuil roulant populaires d'autres marques

Otto Bock

Otto Bock Skippi plus Manuel utilisateur

Invacare

Invacare Action 4NG series Manuel utilisateur

SORG

SORG LoopSORG 802 Manuel utilisateur

Designability

Designability WizzyBug Instructions d'installation

Vermeiren

Vermeiren RAPIDO Manuel utilisateur

Excel

Excel G5 KIDS 0285 Manuel utilisateur

M. Bartels

M. Bartels SA-3 Manuel utilisateur

nino robotics

nino robotics NIno Manuel utilisateur

Vermeiren

Vermeiren Turios Manuel utilisateur

Invacare

Invacare MK5 EX Manuel utilisateur

Invacare

Invacare Solara Spree GT Manuel

Nova

Nova TKW-12 Manuel utilisateur

BCW

BCW Advantage Manuel utilisateur

You-Q

You-Q Luca Manuel utilisateur

interco

interco Ortolight Standard Mode d’emploi

Nova

Nova 7190L Manuel utilisateur

Vermeiren

Vermeiren EZ1 Manuel utilisateur

PaceSaver

PaceSaver Scout M-300 Manuel utilisateur