DCS TDS1-20 Manuel utilisateur
US CA
590615B 08.14
TDS1-20, TDD1-20, TDT1-20,
TB1-20, DP1-42 & BC25 models
Outdoor Storage
INSTALLATION INSTRUCTIONS
SAFETY AND WARNINGS
1
IMPORTANT SAFETY INSTRUCTIONS!
Do not remove permanently affixed labels, warnings, or plates from the product. This may void the
warranty.
Please make this information available to the person installing the appliance as it could reduce your
installation costs.
Please leave these instructions with the appliance. Inform the customer to retain for future reference
and for the local inspectors’ use.
Failure to install the appliance correctly could invalidate any warranty or liability claims.
Only genuine replacement parts may be used for servicing the appliance. These are available from
your nearest Fisher & Paykel Service Center.
the countertop is square and level and no structural members interfere with space requirements
Do Not store or use gasoline or other flammable vapors and liquids inside or in the vicinity of this or
any other appliance.
An LP cylinder not connected for use shall not be stored inside or in the vicinity of this unit.
WARNING!
Cut hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
WARNING!
Crush hazard
Closing drawers may cause injury to your hands or fingers.
Always close or open drawers using their handles.
Be sure to keep hands away from drawer edges when opening or closing
drawers.
Failure to use caution could result in injury or cuts.
3
MODEL LINE UP
TOOLS REQUIRED (NOT SUPPLIED)
2
3
TDS1-20
TDD1-20
TDT1-20
DP1-42
TB1-20 BC25
DRAWERS WASTE BASKET BEVERAGE CHILLERPANTRY
BOTTLE HOLDER
Screwdriver 2 - Wrench
Tape
measure Safety GlassesPencil
Adjustable
pliers
Adjustable
wrench
Suitable protective
gloves Drill
Hammer
BC-BOTTLEAC-25
4
4PRODUCT DIMENSIONS - DRAWERS, PANTRY & WASTE BASKET
Product dimensions inches (mm)
TDS1-20
TDD1-20
TDT1-20
TB1-20
DP1-42
Aoverall height of product 9 ⁄”(245) 21 ⁄”(556) 29 ⁄”(740) 29 ⁄”(740) 30 ½”(775)
Boverall width of product 20 ⁄”(516) 20 ⁄”(516) 20 ⁄”(516) 20 ⁄”(516) 42”(1066)
Cwidth of chassis 18 ½”(469) 18 ½”(469) 18 ½”(469) 18 ½” (469) 40 ” (1016)
Ddepth of chassis 23 ”(585) 23 ”(585) 23 ”(585) 23 ”(585) 23 ⁄”(601)
Edepth of front frame (excluding handle) 2”(51) 2”(51) 2”(51) 2”(51) 2”(51)
Fheight of chassis 8 ⁄”(210) 20 ½”(520) 27 ⁄”(705) 27 ⁄” (705) 29” (736)
TOP
C
D
E
B
AF
FRONT SIDE
TB1-20 model shown for illustration purposes
5
5CABINETRY DIMENSIONS (PROUD INSTALLATION) - DRAWERS, PANTRY & WASTE BASKET
Cabinetry dimensions inches (mm)
TDS1-20
TDD1-20
TDT1-20
TB1-20
DP1-42
Aoverall height of cutout 8 ⁄”(215) 20 ⁄”(525) 28 ”(710) 28 ”(710) 29 ⁄”(741)
Boverall width of cutout 18 ⁄”(480) 18 ⁄”(480) 18 ⁄”(480) 18 ⁄”(480) 40 ⁄”(1026)
Cheight from ground to bottom of cutout min. 1 ⁄”(30) min. 1 ⁄”(30) min. 1 ⁄”(30) min. 1 ⁄”(30) min. 1 ⁄”(30)
90º
A
C
B
SIDE
ISO
6
5CABINETRY DIMENSIONS (FLUSH INSTALLATION) - DRAWERS, PANTRY & WASTE BASKET
Cabinetry dimensions inches (mm)
TDS1-20
TDD1-20
TDT1-20
TB1-20
DP1-42
Aoverall height of cutout 9 ⁄” (249) 22 ⁄”(560) 29 ⁄”(745) 29 ⁄”(745) 30 ⁄”(779)
Boverall width of cutout 20 ½”(521) 20 ½”(521) 20 ½” (521) 20 ½”(521) 42 ⁄”(1072)
Cheight from ground to bottom of cutout min. 1 ⁄”(30) min. 1 ⁄”(30) min. 1 ⁄”(30) min. 1 ⁄”(30) min. 1 ⁄”(30)
Dsetback for ush installation 2”(51) 2”(51) 2”(51) 2”(51) 2”(51)
90º
A
C
D
B
TB1-20 model shown for illustration purposes
FRONT SIDE
Minimum 3/16” (4 mm)
cutout clearance
around front frame
A frame should be constructed 2” (51 mm) setback from the front face
of the product to both push the product up against and conceal the
cutout clearance around the front frame.
Important!
Do not seal the product in with silicone caulk or similiar. Doing so will
result in the product being difficult to remove for servicing.
ISO
7
90º
H
I
G
B
B
CF
D
E
A
K
90º
H
I
G
90º
H
J
G
I
6PRODUCT & CABINETRY DIMENSIONS - BEVERAGE CHILLER / BOTTLE HOLDER
Cabinetry dimensions inches (mm)
BC25
Aoverall depth of product (including lid) 21 ⁄”(557)
Boverall width of product (including lid) 26 ⁄”(670)
BIoverall width of product (excluding lid) 25 ⁄”(636)
Cwidth of chassis 23 ⁄”(608)
Dheight of chassis (below countertop) 9 ⁄”(249)
Eheight of frame (including lid) 2 ¼” (57)
Fdistance from rear of chassis to centre of drain 5 ⁄”(142)
Goverall width of cutout 24 ⁄”(615)
H
depth of cutout:
without bottle holder accessory
including bottle holder accessory
21 ⁄”(535)
21 ⁄”(550)
Iminimum distance from front of countertop to cutout ⁄”(15)
Jheight of cutout for bottle holder accessory 9 ⁄”(250)
Kdepth of bottle holder at widest point to front of frame 6 ⁄”(168)
TOP
90º
H
J
G
FRONT SIDE
WITHOUT BOTTLE HOLDER ACCESSORY INCLUDING BOTTLE HOLDER ACCESSORY
Make sure the countertop is square and level and no
structural members interfere with space requirements.
8
7a DISCARD PACKAGING
Recycle responsibly
Model may vary from illustrations shown
8a REMOVE ALL DRAWERS TO ACCESS SCREW HOLE LOCATIONS
Inspect the product(s) to verify that there is no shipping damage.
If any damage is detected, call the shipper and initiate a damage claim.
DCS by Fisher & Paykel is not responsible for shipping damage.
NOTE: Do not discard any packing material until the unit has been inspected.
Operate the drawers to be sure they glide smoothly.
Examine the fronts to be sure there are no dents or scratches or discoloring.
INSTALLING DRAWER UNITS, WASTE BASKET
To remove the drawer(s)
1
Remove the drawers by pulling them
out until the slider latch is visible.
2
Carefully push the latch down on the
left side, while lifting up the latch on
the right side.
3
Pull the drawer out of the frame.
Note: to prevent damage to surfaces, place
the drawers on a stable surface on a
protective towel or table cloth.
Left Slider latch
Right Slider latch
9
Allow min. 1 ⁄” (28mm)
clearance from the cutout to a
corner
Allow min. 4” (102 mm) clearance
from the cutout to a corner
Refer to Pantry installation for corner installations with a
pantry unit or beverage unit with bottle holder.
measured from
back of frame
measured from
back of frame
9a PREPARE THE CAVITY
Ensure the cavity is level, square and able to support the weight of the product
when full.
Any cabinet and/or ground preparation must be completed prior to installation.
All support structures must be constructed of materials resistant to moisture
damage.
Do no use harsh products (acid, solvent, sealers) around this product.
1
Depending on your construction, place either a shelf or at least two
(min 2” (51 mm) wide) moisture resistant supports in the cutout.
Ensure all support boards are flat and level.
16 ½”
(420 mm)
20 ½”
(520 mm)
1 ¼”
(31 mm)
min. ⁄”
(11 mm)
min. 1⁄”
(30 mm)
16 ½”
(420 mm)
20 ½”
(520 mm)
1 ¼”
(31 mm)
min. 1 ⁄”(28 mm)
min. 4”(102 mm)
min. 4”(102 mm)
TDS1-20 ONLY
CORNER INSTALLATION
CORNER INSTALLATION WITH TWO PRODUCTS
Provide a support behind
the chassis to screw into
TDD1-20, TDT1-20 & TB1-20 ONLY
Provide a support above the
chassis to screw up into
10
10a INSERT PRODUCT INTO CAVITY & SECURE
1
With the help of an assistant, lift the unit and slide it into the cabinet cutout along the supports. Adjust for level and fit.
2
Locate the mounting holes (front and rear of base on each side).
Single Drawer TDS1-20 only:
If you find the rear base screw hole locations inaccessible, you may screw through the rear chassis panel into the support behind the unit.
3
Secure the unit using screws suitable for the type of cabinetry materials used. We recommend using all the shown hole locations for securing.
T
DD1-20, TDT1-20 & TB1-20 ONLY
Alternatively screw
through rear chassis panel
into support behind
Refer to Step 9a for screw
mounting hole positions
Refer to Step 9a for screw
mounting hole positions
TDS1-20 ONLY
Ce manuel convient aux modèles suivants
5
Table des matières
Langues :
Manuels Entreposage extérieur populaires d'autres marques
Lifetime
Lifetime 6418 Manuel utilisateur
rollaway container
rollaway container ARPCA24 Manuel utilisateur
Duratuf
Duratuf Havelock Manuel utilisateur
X-METAL
X-METAL 4065 Manuel utilisateur
Outdoor Life Products
Outdoor Life Products FP2030 F Manuel utilisateur
Royalcraft
Royalcraft Faro 295L Storage Box Manuel utilisateur
