DCL Camatics VT2500 Instructions de montage

27 October 2021

Camatics

Fitting Guide

 

 
1CONTENTS 
Important Information ____________________________________________________________ 2 
Installation Dos and Don’ts_________________________________________________________ 3 
1 Power _____________________________________________________________________ 3 
2 Securing the device___________________________________________________________ 3 
Introduction ____________________________________________________________________ 4 
1 Front ______________________________________________________________________ 4 
2 Side _______________________________________________________________________ 4 
3 Back_______________________________________________________________________ 5 
4 Power Cable Colours__________________________________________________________ 5 
Functions_______________________________________________________________________ 6 
1 Automatic Booting ___________________________________________________________ 6 
Installation _____________________________________________________________________ 7 
1 Preparation _________________________________________________________________ 7 
2 Hardware __________________________________________________________________ 7 
3 Wiring _____________________________________________________________________ 7 
4 G-Sensor Calibration __________________________________________________________ 7 
5 Device Commissioning ________________________________________________________ 8 
6 Camatics Job Sheet ___________________________________________________________ 8 
 
 

2IMPORTANT INFORMATION

•If you have any questions or concerns regarding this document, the hardware you have received

or the requirements of your Camatics Insurance Policy, please contact you broker immediately.

•Before you begin installing and commissioning the system, please ensure that you have read this

manual thoroughly, referring to any supplementary information provided for the unit as

required.

•Care must be taken in the routing of all cables so that the insulation does not become worn or

damaged.

•Unauthorised modification to this equipment or associated accessories is forbidden without the

expressed permission and agreement from the product manufacturer.

•This equipment should not be operated in hazardous environments i.e. areas that contain

explosive materials or flammable vapours.

•This equipment should not be operated within aircrafts or in close proximity to medical

equipment.

•This equipment may only be located in a position where it cannot interfere with the normal

operation of the vehicle or present a hazard to the driver or passengers.

•Failure to comply with the following Warnings, Approval and Safety information may invalidate

warranty, certification or type approval of this product.

•All installation and service work must be carried out in accordance with FCS1362, FCS1372,

RQAS, 95/54/EC, ISO 21609 and / or any other statutory guidelines or Directives currently in

force. Therefore it is strongly recommended that the unit is installed and commissioned by

suitably trained and qualified installation personnel with accreditation.

•Under no circumstances may any part of the product be installed inside the engine

compartment area.

•Unauthorised changes or alterations to the equipment or the installation will invalidate

certification issued by the Approved Accreditation Bodies and may also affect the vehicle

manufacturers warranty

3INSTALLATION DOS AND DON’TS

3.1 POWER

The device MUST be wired to its own power supply and not connected/shared with an existing power

pickup point. We recommend that the vehicle power pickup points should be located using the vehicle

manufactures instructions.

YOU MUST NOT USE ANOTHER TELEMATICS PROVIDER’SPOWER SUPPLY

OR PICK UP POINTS TO POWER THIS DEVICE

To avoid interference the power supply MUST be installed as far away from other Telematics devices

and power supplies already installed within the vehicle as possible. Ideally on the opposite side of the

vehicle.

3.2 SECURING THE DEVICE

Please note the installation location on the windscreen MUST NOT be in the marked area “As shown

below”

The dash camera has an internal accelerometer to measure harsh driving events so you MUST ensure

that it is firmly secured in the vehicle.

You MUST ensure that the device is calibrated as part of the commission process.

4INTRODUCTION

4.1 FRONT

4.2 SIDE

4.3 BACK

4.4 POWER CABLE COLOURS

5FUNCTIONS

5.1 AUTOMATIC BOOTING

Once the VT2500 has been wired to your vehicle power source, the VT2500 will boot up. This will take

around 1 minute for the unit to be ready to record.

Please note, the unit will not start recording immediately after the power is on. It takes around 1 minute

for the built-in power backup system to charge. Once the unit is charged, the internal flash memory will

be ready to record.

6INSTALLATION

6.1 PREPARATION

1. Park your vehicle on a flat level surface.

2. Turn off the engine before installing the VT2500.

6.2 HARDWARE

1. Attach the VT2500 to the windscreen using the provided double sided 3M pad.

The surface must be clean and dry before you install the camera. We recommend you install the

product behind the rear view mirror on the front windshield. The 3M adhesive pad will not stick

well with dust or oil, etc. Please make sure the surface is clean before applying

2. Adjust the camera view and make sure the lens has an unobstructed view. Check the camera

angle from the outside of the vehicle. You can adjust the angle via the camera's bracket.

3. Arrange the power cord neatly alongside the windshield and door pillar trim.

6.3 WIRING

1. The VT2500 requires a continuous 12/24volt power source from the vehicle.

The cable supplied will allow you to hard wire the VT2500 unit to the fuse box of your vehicle.

2. Connect the “red cable (+)” to a fuse.

It should be connected to a fuse that has power only when you start the engine.

3. The ground cable should be contacted at the vehicle body or battery negative.

4. Start the vehicle after installation.

5. You must keep the vehicle powered on for at least 10 minutes following initial power-up of the

camera. Not doing so may result in damage to the camera and it not working correctly.

DO NOT TURN OFF THE VEHICLE DURING THIS TIME

6.4 G-SENSOR CALIBRATION

The G-Sessor will require calibration after installing the VT2500

1. Turn on the vehicle and press the red panic button for three seconds.

2. Calibration is complete when you hear a “beep”.

6.5 DEVICE COMMISSIONING

1. Leave the vehicle and camera on for 5 minutes after calibration

2. Call VisionTrack on 01246 223 152 to commission the device. Please have the following

information ready:

oVehicle Registration

oDevice DRID –found on the device’s green sticker

oPolicy name

3. You will be provided with a commission reference –please note this down

6.6 CAMATICS JOB SHEET

Please go to https://www.camatics.co.uk/jobsheet and complete the Camatics Job Sheet. You will

require the following:

•Policy Number

•Vehicle Registration

•Device DRID –found on the device’s green sticker

•VisionTrack Commission Reference

•Photo of the inside of the vehicle showing the camera affixed to the windscreen

•Photo of the camera, showing the DRID

•Photo of the front of the vehicle, showing the registration plate and windscreen

Table des matières

Autres manuels DCL Caméra embarquée

DCL

DCL VT3600 Manuel utilisateur

Manuels Caméra embarquée populaires d'autres marques

Cansonic

Cansonic UltraDuo Z2 Manuel utilisateur

Gazer

Gazer F720 Manuel utilisateur

HP f500g Manuel utilisateur

Xblitz

Xblitz TANGO 4K Manuel utilisateur

Rexing

Rexing M1 Manuel utilisateur

Maka Technologies

Maka Technologies Marbella MXPro Manuel utilisateur

NESA

NESA NRC-80DLM Instructions d'installation et d'utilisation

Kaiser Baas

Kaiser Baas R20 Manuel utilisateur

Boyo

Boyo VTM43TC Manuel utilisateur

Minolta

Minolta MNCD37 Manuel utilisateur

Thinkware

Thinkware FA10 Manuel utilisateur

Momento

Momento MD-5200 Manuel utilisateur

BlackVue

BlackVue DR590X-1CH Manuel utilisateur

HP F300 Manuel utilisateur

CammSys

CammSys BlackSys BH-300 Manuel utilisateur

Snooper

Snooper DVR-2HD Manuel utilisateur

Lukas

Lukas Q900 Manuel utilisateur

RVS

RVS 450C Manuel utilisateur