DayTronic M2 Manuel utilisateur

Technical features:

• 6-digit red display (optional: green, orange, blue)

• minimal installation depth: 70 mm excluding plug-in terminal

• programming interlock via access code

• protection class IP65 (front side)

• plug-in terminal

User manual M2

Profibus DP

96x48

M2_1B9GB.pdf updated: 08.03.2012

Identification

M2-1BR6B.9000.570BD

M2-1BR6B.9000.670BD

Profibus

Housing size: 96x48 mm

ORDER NUMBERSTANDARD TYPES

Please state physical unit by order, e.g. m/min.

Options – breakdown order code:

M2-1B

6B.9000.670BD

Standard type M-Line Dimension

D physical unit

Installation depth

89 mm incl. plug-in terminal 2 Version

Housing size

B96xH48xD70 mm 1 Setpoints

0nosetpoints

Display type

binary B Protection class

1 without keypad,

Display colour operation on the back

Blue B 7 IP65 / plug-in terminal

Green G

Red R Supply voltage

Yellow Y 4 115 VAC

5230VAC

Number of digits 6 10-30 VDC galv. insulated

6-di

it 6

Measuring input

Digit height 0none

14 mm B

Analog output

Digital input 0none

Profibus 9

Sensor supply

0none

Contents

1. Assembly 2

2. Electrical connection 3

3. Function and operation description 4

4. Setting up the device 5

4.1. Switching on 5

4.2. Parametrisation 5

5. Operating modes 7

5.1. Operating mode 1 7

5.2. Operating mode 2 7

5.3. Operating mode 3 8

5.4. Operating mode 4 8

5.5. Operating mode 5 9

5.6. Explanations to panel parameters 10

5.7. Explanations to the position after decimal point 10

5.8. Explanations to the mode 11

5.8.1 Modus 0 11

5.8.1 Modus 1 ´ 11

6. Error indications 12

7. Factory settings 13

7.1. Synoptical table 13

7.2. Reset to factory settings 13

8. Technical data 14

9. Safety advice 15

1. Assembly

Please read the Safety advice on page 15 before installation and keep this user manual

for future reference.

Sealing

48,0

3,0

Gap for physical unit

89,0

1. After removing the fixing elements, insert the device.

2. Check the seal to make sure it fits securely.

3. Click the fixing elements back into place and tighten the clamping screws by hand.

Then use a screwdriver to tighten them another half a turn.

CAUTION! The torque should not exceed 0.1 Nm!

The dimension symbols can be exchanged before installation via a channel on the side!

2. Electrical connection

2. Electrical connectio

Connection example:

Profibus arranges the devices in sequence. An allocation in form of a star is not acceptable! Both ends of the

data line require a termination. One in the triggering included termination needs to be activated. The maximum

allowable length of the data line depends on the baudrate an is 1000 m.

For simplification of the electrical connection, the terminals are carried out doubly. At the last device of tha

bus-line, the termination can be switched onto the bus-line with two bridges.

3. Function and operation description

Operation

The device is triggered via Profibus and shows numerics and signs in a 6-digit 7-segment

display.

Thereby the communication can be triggered via a Bus master. The display recognizes

automatically the used Baudrate with a Bus master and needs as single information the

Profibus address, which can be parametrised via the keypad of the display.

Parameterisation level:

Parameter deposited in the menu item can here be parameterised.

Functions, that can be changed or adjusted, are always signalised by a flashing of the

display. Settings that are made in the parameterisation level are confirmed with [P] and thus

safed. By pressing the [O]-key (zero-key) it leads to a break-off of the value input and to a

change into the menu level.

All adjustments are safed automatically by the device and it changes into operating mode, if

no further key operation is done within the next 10 seconds.

Operation and display elements:

Change into menu level or break-off in value input.

Parameterisation

level Adjustment of the value / the setting.

Keys for up and down navigation in the menu level.

DescriptionKey

To confirm the changes made at the parameterization level.

Change into operation mode.

Change to parameterisation level and deposited values.

Menu level

Level

4. Setting up the device

Adjusting the brightness brt:

With this parameter the brightness of the display can be reduced onto 25% of the total

brilliancy. With [P] the selection is confirmed and the device switches back into menu

level.

Setting the decimal point, dot:

The decimal point on the display can be moved with [▲] [▼] and confirmed with [P].

The display then switches back to the menu level again.

Selection of the device address Adr:

Device addresses from 1-125 can be parametrised. The address 126 is preset as

default value, which is the delivery state. After changing this parameter, the device

does a soft test bevor switching back into operation mode. After this, the new address

will be directly in use.

Parameterisation levelMenu level

4.1. Switching-on

Once the installation is complete, you can start the device by applying the voltage supply.

Before, check once again that all electrical connections are correct.

Starting sequence

For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed

followed by an indication of the software type and, after that, also for 1 second the software

version. After the starting sequence, the device switches to operation/display mode.

4.2. Standard parameterisation: (Flat operation level)

To parameterize the display, press the [P] key in operating mode for 1 second. The display

then changes to the menu level with the first menu item TYPE.

4. Setting up the device

Administrator code / Master code (4-digit number-combination free available),

A.Co:

With this code all parameters can be re-activated, after LOC has been activated under

menu item run before. By pushing [P] in operation mode for approx. 3 seconds, CodE

occurs in the display and enables the user to reach all parameters by entering the

A.co. While leaving the parameterisation under run, the parameterisation can be

activated permanently by selection of ULC. So that at a renew pushing of [P] in

operating mode, no new entering of the code needs to be done.

Activiation / Deactivation of the programming interlock or closing-off of the

parametrisation, run:

With the navigation keys [▲] [▼], one can choose between the deactivated key lock

Uloc (works setting) and the activated key lock Loc. Confirm the selection with [P].

After this, the display confirms the settings with "-----", and automatically switches to

operating mode. If Loc was selected, the keyboard is locked. To get back into the

menu level, press [P] for 3 seconds in operating mode. Now enter the CODE (works

setting 1 2 3 4) that appears using [▲] [▼] plus [P] to unlock the keyboard. FAIL

appears if the input is wrong. By pressing [P] in operation mode for approx. 3

seconds, the first menu group adr appears in the display and thus confirms the

change into parameterisation. It stays activated as long as ULOC is entered in menu

group RUN, thus the display is set back in standard parameterisation again.

Parameterisation levelMenu level

5. Operating modes

The Profibus displays support 5 different operating modes, as given below.

Display value „signed integer“0x21

FunctionDescriptionCharacteristicByte-No.

2 Bytes output data0

5. Operating modes

5.1. Operating mode 1

Display of 16 bit signed integer values (-32768…32767).

Configuration values

Output data

Display value High-Byte

FunctionByte-No.

Display value Low-Byte1

Position after decimal point „signed integer“

Position after decimal point (see 7.7)

0x21

0x20

Panel parameter (see 7.6.)0x21

FunctionDescriptionCharacteristicByte-No.

2 Bytes output data2

1 Byte output data1

2 Bytes output data0

5.2. Operating mode 2

Display value of 16 bit signed integer values (-32768…32767), with brightness control,

flashing and position after decimal point.

Configuration data

Output data

Display value High-Byte3

Position after decimal point (see explanations under 7.7)

Panel parameter (see explanations under 7.6.)

FunctionByte-No.

Display value Low-Byte4

0-1

5. Operating modes

Display value „signed long integer“0x23

FunctionDescriptionCharacteristicsByte-No.

4 Bytes output data0

5.3. Operating mode 3

Display value of 32 bit signed integer values (-4.294.967.296…4.294.967.295).

Configuration data

Output data

Display value Low-Word, High-Byte2

Display value High-Word, Low-Byte1

Display value High-Word, High-Byte

FunctionByte-No.

Display value Low-Word, Low-Byte3

Display value „signed long integer“

Position after decimal point (see 7.7)

0x23

0x20

Panel parameter (see explanations 7.6)0x21

FunctionDescriptionCharacteristicByte-No.

4 Bytes output data4

1 Byte output data1

2 Bytes output data0

5.4. Operating mode 4

Display value of 16 bit signed integer value (-32768…32767), with brightness control,

flashing and position after decimal point.

Configuration data

Output data

Display value High-Word, Low-Byte4

Display value Low-Word, High-Byte5

Display value High-Word, High-Byte3

Position after decimal point (see explanations under 5.7)

Panel parameter (see explanations under 5.6)

FunctionByte-No.

Display value Low-Word, Low-Byte6

0-1

Autres manuels pour M2

Table des matières

Autres manuels DayTronic Instrument de mesure

DayTronic

DayTronic 3770 Manuel utilisateur

DayTronic

DayTronic M3 Manuel utilisateur

DayTronic

DayTronic 3000PLUS Manuel utilisateur

DayTronic

DayTronic 4000 Series Manuel utilisateur

DayTronic

DayTronic 4030 Manuel utilisateur

DayTronic

DayTronic 4500 Manuel utilisateur

DayTronic

DayTronic TM3 Manuel utilisateur

DayTronic

DayTronic 3000PLUS Manuel utilisateur

DayTronic

DayTronic 3000 series Manuel utilisateur

DayTronic

DayTronic 3500 Series Manuel utilisateur

DayTronic

DayTronic 3770P Manuel utilisateur

DayTronic

DayTronic 3000PLUS Manuel utilisateur

DayTronic

DayTronic 4000 Series Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur