DAVIS DriveRight 8140 Manuel utilisateur
H
EAVY
D
UTY
MOUNTING
KIT
Product #’s: 8140, 8143, 8146, 8150
S
TAINLESS
S
TEEL
S
TRAP
M
OUNTING
I
NSTRUC-
TIONS
1
DRIVERIGHT
®STAINLESS STEEL STRAP MOUNTING INSTRUCTIONS
(For use with Heavy-Duty DriveRight® Installation Kits)
Assembly Parts:
• Stainless Steel CableTie
• Stainless Steel Magnet Mount
• Magnet
• Neoprene Rubber Strip
Tools Required: To assure that sufficient tension is applied to the stainless
steel cable tie to prevent slipping of the Magnet Holder Assembly, a tension-
ing tool must be used.
Two tensioning tools are available:
• The“Screwdriver”type
• The“Squeeze Handle”type
If the “screwdriver type is used, snips or cutters will be needed to trim the
stainless steel cable tie.
INSTALLATION INSTRUCTIONS
NOTE:
Once the end of the cable tie is inserted into the clasp, it cannot be removed. Do this only
when you are ready.
1. Measure the neoprene rubber strip.Wrap it around the driveshaft at the location
where the magnet is to be placed. Cut the rubber strip squarely so that a 1.5”
gap is left between the ends.This gap is where the magnet should be placed.
2
2. Install the magnet into the holder and slide the stainless steel cable tie into the
holder,securing the magnet inside. Note the orientation of the clasp to the
holder.
3. Place the neoprene rubber strip around the driveshaft and loosely wrap the
stainless steel cable tie over the rubber strip,positioning the magnet holder in
the 1.5”gap (the magnet holder should rest directly on the shaft). Insert the end
of the stainless steel cable tie into the clasp and slowly tighten. Position the
clasp180˚ from themagnet on theshaft.When everythingis properlyinposition,
tighten the cable tie by hand.
4. Proceed to the tightening instructions for the tightening tool you have.
“SCREWDRIVER” TYPE TIGHTENING TOOL
1. Trim the stainless steel cable tie using cutters or tin snips so that 2”remains
protruding from the clasp.
2. Insert the end of the stainless steel cable tie into the slot at the end of the
tightening tool. Grip the tool by the handle and hold the magnet in place. Slowly
twist the tool to further tighten the cable tie. Rotate the tool so that the tool tip
goes down toward the clasp and under the remaining tie.
3. When the desired amount of tension has been reached and the magnet is
secure,slide the tool out of the center of the coil. Flatten the rolled coil against
the shaft.
Cross section of
the tensioned tie
3
“SQUEEZE HANDLE” TYPE TIGHTENING TOOL
Slide the installation tool over the stainless steel cable tie as shown and squeeze the
handle to apply tension. If the handle is all the way closed and more tension is
needed, release the handle and slide the tool towards the clasp. Again squeeze the
handle until jthe desired tension has been reached.To cut off the end of the cable
tie, hold tension and twist (either clockwise or counterclockwise).
P/N 07395.058, Rev. C. 10/6/99
3465 Diablo Avenue, Hayward, CA 94545-2778
510-732-9229 • Fax: 510-732-9188
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels DAVIS Support et étagère
DAVIS
DAVIS with the Integrated Sensor Suite (ISS) of the Vantage Pro2TM... Manuel utilisateur
DAVIS
DAVIS Sensor Tilting Bracket Manuel utilisateur
DAVIS
DAVIS Antenna Mast-Mount Kit Manuel utilisateur
DAVIS
DAVIS Sensor Mounting Arm Manuel utilisateur
DAVIS
DAVIS Antenna Mast-Mount Kit Manuel utilisateur
DAVIS
DAVIS Mounting Tripod Kit Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
