Dateq SPL-D2 Manuel utilisateur
DATEQ BV
E-mail: [email protected]
Bank: IBAN NL 88 RABO 0301019444
e Paal 37, 1351 JG Almere – Holland
Internet: www.dateq.nl
Bank swift RABO NL2U
Tel.: +31 36 5472222 Fax: +31 36 5317776
Skype: dateq_audio
Chamber of commerce no: 39031467
Spl-D2 Next generation
DATEQ SPL-D2 Manual
Introduction
The SPL-D2 unit is a separate sound-level meter. Besides it can be linked to the SPL5 limiter. The
unit is a large LED displa , showing the actual sound-pressure level.
B means of the PC software it is possible to change the settings.
Product support
For questions about the SPL limiter series, accessories and other products please contact:
DATEQ Audio Technologies
De Paal 37
1351 JG Almere
The Netherlands
Telephone: +31 36 - 5472222
Fax: +31 36 - 5317776
E-mail: [email protected]
Web: www.Dateq.nl
DATEQ BV
E-mail: [email protected]
Bank: IBAN NL 88 RABO 0301019444
e Paal 37, 1351 JG Almere – Holland
Internet: www.dateq.nl
Bank swift RABO NL2U
Tel.: +31 36 5472222 Fax: +31 36 5317776
Skype: dateq_audio
Chamber of commerce no: 39031467
Operation
DATEQ SPL-D2 Manual
Display connected to the SPL5
When the displa is linked to the SPL5 the microphone values will be downloaded from the SPL5
automaticall . Those values will be showed in the large displa .
The LED-bar functions as a VU-meter, the displa gives the actual SPL.
As soon as the sound-level exceeds the pre-set threshold the LED's will light up red.
Connecting to the SPL5
The displa unit is connected to the SPL with the jack connector. A standard microphone cable
can be used. Connect the shield to the jacks' ground pin and the signal wires to the tip. At the SPL5
the shielding can be connected to pin 14, and the signal wire to pin 8 of the DB-25 connector.
Using the display stand-alone
To use the displa as a stand-alone device the
microphone has to be connected. The audio-
level will be showed in the large LED displa .
By means of the PC-software the threshold can
be adjusted. When the audio-level exceeds this
level the LED s will become red. This can be
used as a warning for the live-band, or the disk-
jockey.
The displa units hold three correction-curves:
• ANSI-A
• ANSI-B
• ANSI-C
The measured values can be adjusted to match
a calibrated meter. B moving the slider to the
right the microphone becomes more sensitive.
Moving the slider
to the left gives a higher level.
Common settings
The displa can be dimmed automaticall in a dark environment. This function can be enabled b
selecting 'Auto ambient light correction’
The intensit of the ‘numbers and the Vu meter can be adjusted with the sliders as can be the
response time of the Vu meter.
DATEQ BV
E-mail: [email protected]
Bank: IBAN NL 88 RABO 0301019444
e Paal 37, 1351 JG Almere – Holland
Internet: www.dateq.nl
Bank swift RABO NL2U
Tel.: +31 36 5472222 Fax: +31 36 5317776
Skype: dateq_audio
Chamber of commerce no: 39031467
Technical Specifications
DATEQ SPL-D2 Manual
Inputs
Mic (measuring microphone) XLR- 3 female. To be used with the supplied
measuring microphone only
ack 6,3 mm ack. Datalink to the SPL-5
USB To connect the SPL-D2 to a computer
Norm Measurement chain designed to function
according specifications IEC-61672-1 class 2
Common
Supply
Input voltage 24 V dc
Power consumption 9 W
Dimensions and weight
Cabinet 255 mm x 125 mm x 47 mm (b x h x d)
Weight 1 Kg
Autres manuels pour SPL-D2
1
Table des matières
Autres manuels Dateq Instrument de mesure
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur