DataRemote CDS-9010 Manuel utilisateur
USER MANUAL
CDS-9010
WHAT
CAN YOUR
NEW DEVICE DO?
Virtually every application
that requires a copper hard-line
can now be replaced with one device!
Dual Band Wi-Fi Router
LTE VoIP
Revision No. 004 April 2020
ONE DEVICE
TO REPLACE ALL YOUR LANDLINES
The DataRemote CDS-9010 wireless router with VoIP is a stand-alone device which facilitates
clear and reliable voice quality over the Internet. It is fully compatible with Session Initiation
Protocol (SIP) industry standards and can integrate with many other SIP devices and software
on the market.
HARDWARE INSTALLATION
FOLLOW ALL THE STEPS AS SHOWN ON THE PICTURES AND THE DESCRIPTION. IF
YOU HAVE ANY QUESTIONS RELATED TO THE HARDWARE INSTALLATION, PLEASE
CONTACT THE SUPPORT NUMBER PROVIDED ON YOUR DEVICE’S BOX.
LTE DIV
LAN2 LAN2 WAN
RESET
DC 9-16V
PHONE 2 PHONE 1
LTE MAIN
DATAREMOTE
DEVICE MANAGER
Meter Reading
Voice
Fire Alarms
Burglar Alarms
Elevator
Fax
Emergency Call Box
Point of Sale
Security Gate / Door Access-box
Modem Data
PSTN
LTE/WAN PBX
DATA
Page 2
Revision No. 004 April 2020
DataRemote offers enterprise-grade solutions for traditional landline replacement.
Our suite of products converts all your existing legacy landlines to next generation
service via VoIP and the LTE cellular network whether it be voice, Fax lines, burglar,
fire alarms, elevators, ATM's, emergency call boxes, point of sale systems and more.
TABLE OF CONTENTS
What comes in the Box
What do you need to know before installing your device
LED Lights Indicators
What is on the front of your device
Basic Installation (Step by Step)
Service Technician Installation
Overview
Scope of Work
Materials List
Pre-Work
Phase 1 – DataRemote CDS-9010 device Assembly/Pre-Test + Fire Panel Location
Phase 2 - Installation Tasks – Locate Existing POTS Lines
Phase 3 - Cut-over Fire Panel Lines to New DataRemote CDS-9010 device
Phase 4 - Testing Fire Alarm Communication over DataRemote CDS-9010 device
Phase 5 - Testing Fax Lines
Phase 6 - Testing Analog Data Lines
Post Installation Tasks
Deliverables
Advanced Programming Information
Statements and Disclaimers
Page 3
Revision No. 004 April 2020
WHAT COMES IN THE BOX
RJ11 PHONE
CABLES X2
RJ-45 ETHERNET
CABLE X1
100-240V-50/60HZ,
POWER ADAPTER X1
DATAREMOTE CDS-9010
CELLULAR APPLIANCE X1
SET OF MOUNTING
HARDWARE X1
INTERNAL BATTERY X1 INTERNAL CASE FOR EXTRA BATTERY X1
LTE ANTENNAS (SMA-M CONNECTORS) X2
Page 4
Revision No. 004 April 2020
Before you can connect your DataRemote CDS-9010 device to the Internet and use it, you must
have access to high-speed Internet. A high-speed Internet connection can be accessed through
DSL, LTE wireless network, cable modem, Wi-Fi access point, and/or a leased line.
Make sure you are connecting your new DataRemote CDS-9010 device near a power source and
away from extreme heat / humid sources.
As this device uses LTE, please make sure that wherever you are installing the device, there is good
cell reception. The device should also be installed in a location which is easily accessible.
WHAT DO YOU NEED TO KNOW
BEFORE INSTALLING YOUR DEVICE
IMPORTANT:Please refrain from putting furniture or other obstacles in front of the device
as it might influence the signal, thus degrading the quality of service.
LED LIGHTS INDICATORS
NOTE: Before you use your device, please get acquainted with the LED indicators and
connectors first.
TOP PANEL
LED STATUS
LED STATUS EXPLANATION
POWER
BATTERY
Solid (GREEN)
Flashing (GREEN)
OFF
Solid (GREEN)
Solid (BLUE)
The router is powered on (External Power) and running normally.
The router is powered on (Internal Power - BAT) and running normally.
The router is powered off.
Battery charged
Battery charging
Solid (RED) Battery discharging
Page 5
Revision No. 004 April 2020
LED LIGHTS
INDICATORS (continued)
LED STATUS EXPLANATION
WAN ETH
LAN 1
Wi-Fi
PHONE 1
PHONE 2
CELL
OFF
Solid (GREEN)
OFF
Solid (GREEN)
Solid (GREEN)
OFF
Solid (GREEN)
Flashing (GREEN)
OFF
Solid (GREEN)
Flashing (GREEN)
OFF
Strong: All bars solid green
Only three bars Solid green
Two bars are solid green
One bar is solid green
OFF
LTE WAN IP is assigned.
Disconnected
WAN ETH IP is assigned.
Disconnected
Cable connected to the LAN port
The Wi-Fi radio is on
The Wi-Fi radio is off
Registered
On calling / Pick up phone
Not registered
Registered
On calling / Pick up phone
Not registered
RSSI < -50 dBm to -79 dbm
RSSI < -80 dBm to -89 dBm
RSSI < -90 to 100 dBm
RSSI 101 -120 dBm
RSSI 120 dBm and below
CELL DCD Solid (GREEN)
LAN 2 Solid (GREEN) Cable connected to the LAN port
TOP PANEL
LED STATUS
Page 6
Revision No. 004 April 2020
WHAT IS ON THE
BACK OF YOUR DEVICE
REAR PANEL INTERFACE DESCRIPTION
AC Power cord connector outlet DC
Wide Area Network (Internet) connector outlet
Two (2) Ethernet outlets
WAN
LAN1/2
Connector for a power adapter.
Connector for accessing the Internet.
Connectors for local networked devices.
BASIC INSTALLATION
IMPORTANT! Before starting to configure the router, please
connect your device as shown in these "step by step" directions. If
you have any questions regarding installation, please contact the
Support number provided on your device’s Box.
Two (2) FXS phone
line outlets WAN
Wide Area Network
Connector Outlet
Cellular Antennas Connectors
Two (2)
(Connecting
locally)
Ethernet
Outlets
Power Cord
Connector
Outlet
WiFi Antennas
Reset
Button
Page 7
Revision No. 004 April 2020
STEP 1
If your new device did not come with a SIM card pre-installed, please follow the
SIM install directions: Inside the right battery port, the SIM card slots are located
on the left bottom corner of your device. Insert the SIM card inside the slot marked “SIM
1”. Make sure is inserted all the way into the slot. You will feel a spring lock the SIM card
into place.
Insert the batteries in to the battery ports on the sides of your CDS-9010 device, making
sure they will click in place correctly. Then connect one end of the power cord to the
power port of your device. Finally, connect the other end to an electric outlet.
Page 8
Revision No. 004 April 2020
STEP 2
Connect the WAN cable from your modem, switch or router to the WAN port of
your device, with an Ethernet (RJ-45) cable.
DISCLAIMER: This is just a representation of a modem. Models and appearance may vary
depending on your Internet provider.
STEP 3
Page 9
Revision No. 004 April 2020
Connect to one of the two LAN ports on your device with an Ethernet cable (RJ-45)
to your equipment or computer that needs to receive an Internet connection
from the CDS-9010. Your device allows you to connect up to two (2) devices for
Internet access.
Connect the RJ-11 (Phone line) from your phone or equipment requiring a phone
line to the DataRemote CDS-9010 device’s FXS port.
STEP 4
WARNING! Do not connect an active RJ-11 with voltage directly from the wall into the
DataRemote device’s RJ-11 ports, this will damage the device permanently. Each
DataRemote device’s RJ-11 FXS port is an active port supplying voltage. The FXS port is
only to be connected to an FXO analog phone or another FXO device.
Page 10
Revision No. 004 April 2020
Autres manuels pour CDS-9010
2
Table des matières
Autres manuels DataRemote Routeur réseau
Manuels Routeur réseau populaires d'autres marques
NETGEAR
NETGEAR FS526T - Switch Manuel utilisateur
Korenix
Korenix JetNet 5710G Series Manuel utilisateur
Automated Logic
Automated Logic ZN551 Manuel du propriétaire
Cisco
Cisco ASR 1000 Series Manuel de l'opérateur
EnGenius
EnGenius ESR-9710 Manuel utilisateur
Cisco
Cisco 805 Series Instructions d'utilisation et de sécurité