Dataprobe IBoot PoE-P Instructions d'utilisation et d'entretien

PoE Passive

Extender with Reboot

April 2019

Table of Contents

1. General Description 2

2. Hardware Installation 5

3. Initial Configuration 7

4. Web Browser Operation 10

5. Web Setup 13

6. Disable Off 18

7. Local Link Multicast Name Resolution 19

8. iBoot Cloud Service 20

9. Command Line Interface 22

10. DxP Protocol 28

11. Firmware Upgrades 28

12. Troubleshooting 29

13. Specifications 30

14. Technical Support and Warranty 31

Congratulations on purchasing the best network controlled power switch available. The iBoot-PoE-P

provides you the ability to reboot crashed devices automatically or with the click of a mouse. Be sure to

read up on all the features of the iBoot-PoE-P Including:

PoE Extender 100m

PoE Passive 9 –72 VDC up to 90 Watts

Web Based setup and control

Automatic Reboot using AutoPing and Traffic Monitor.

Event Scheduling for real-time power control.

Telnet setup and control

Management Utility: Easy Setup, Firmware upgrades and Reset to Factory Default

iBoot Cloud Service: Control all your iBoots from one web portal.

iboot-poe-p_v190422w iBoot-PoE-P Page 2

1.General Description

The iBoot-PoE-P is a passive PoE extender with automatic and remote controlled reboot and power

switching capability. It is an IP addressed, web controlled power switch for all passive PoE devices.

Anyone with a web browser can access iBoot-PoE-P to perform power On, Off or Power Cycle (Reboot).

iBoot-PoE-P has a web server built in, as well as the ability to be managed through the iBoot Cloud

Service. A simple Web browser interface makes it easy to control power from anywhere in the world with a

click of a mouse. iBoot-PoE-P also supports Telnet for text commands, as well as Dataprobe’s Exchange

Protocol (DxP) for interfacing to a variety of Dataprobe products and custom software development.

1.1. Uses for iBoot-PoE Passive

Automatic reboot of PoE devices –Cameras, Access Points, Phones, etc.

Range Extender –Add 100 meters to PoE runs

iboot-poe-p_v190422w iBoot-PoE-P Page 3

1.2. Automatic Reboot

iBoot-PoE-P provides two ways to monitor your application and provide automatic reboot when

configurable conditions are met

AutoPing

The AutoPing feature allows iBoot-PoE-P to automatically detect failed equipment and perform a timed

reboot or other power control function. You set one or two IP addresses to be periodically pinged. When

iBoot-PoE-P no longer detects a response from these addresses, the programmed power control function

is actuated. The two addresses can be AND or OR linked so that both (AND) or either (OR) need to fail in

order to take the selected action.

With AutoPing, it is also possible to turn ON or OFF the PD when the trigger conditions are met.

See Section 5.5 On AutoPing Setup

Traffic Monitor

Traffic Monitor measures the bandwidth utilization and reboots the PD when the utilization is too low or too

high. It is specifically designed to support high speed access points that crash or degrade over time and

need a quick reboot to get up and running properly.

In addition to setting minimum and (optionally) a maximum traffic, settings allow for monitoring of the

Uplink and/or Downlink, and to disable the traffic monitoring function at specific times of the day, like when

your coffee shop is closed.

See Section 5.5 on Traffic Monitor Setup

Scheduling

Scheduling provides calendar based control of power, to power up or down devices as needed, or to

provide regular reboots to insure proper operation. See Section 0

iboot-poe-p_v190422w iBoot-PoE-P Page 4

1.3. Automatic Self Configuration

In most cases, the iBoot-PoE-P will identify all the network elements required to configure itself for

automatic monitoring and rebooting of a typical PoE environment. The unit will identify the following:

Network Router to obtain an IP address and additional settings for proper network configuration.

(DHCP Server)

Downstream PoE device IP addressed for self-setup of AutoPing monitoring of the PD for automatic

reboot when the PD fails.

In cases where there are multiple IP addresses on the PD side, as when used to protect a network

access point, the iBoot-PoE-P will self-configure for bandwidth monitoring to determine when an

automatic reboot is necessary.

In order for this discovery and self-configuration to take place, the proper installation sequence must be

followed. See Section 2.1 for auto configuration procedure.

1.4. Multiple Control Options

In addition to the Web control capabilities, iBoot-PoE-P features several other means to operate

automatically or under computer control.

URL Control

You can send a single URL to the iBoot-PoE-P containing all the information necessary to query or

change the power status. This makes it easy to create a single button on your desktop or embed into a

batch file or script.

AutoPing

The AutoPing feature allows iBoot-PoE-P to automatically detect failed equipment and perform a timed

reboot or other power control function. You may set 1 or 2 IP addresses to be periodically pinged. When

iBoot-PoE-P no longer detects a response from the address(es), the programmed power control function is

actuated.

Traffic Monitor

In situations where AutoPing is not possible, the iBoot-PoE-P provides a traffic monitoring feature that

can identify slowdowns or failures in bandwidth throughput and auto-reboot when user specified conditions

are met.

Telnet

iBoot-PoE-P’s Command Line Interface (CLI) allows direct control and setup through Telnet.

Dataprobe Exchange Protocol

iBoot-PoE-P supports the Dataprobe Exchange Protocol (DxP) This protocol allows Dataprobe products

to communicate across networks, and allows developers to design custom applications to integrate

iBoot-PoE-P into unique applications. For more information about DxP, contact Dataprobe Support team

([email protected]).

iboot-poe-p_v190422w iBoot-PoE-P Page 5

2.Hardware Installation

2.1. Auto Configuration Sequence

In most cases, the iBoot-PoE-P can completely configure itself on initial installation to identify all network

elements and automatic reboot of failed devices. For the best results follow this sequence when installing

the iBoot-PoE-P for the first time.

1. Connect the PoE OUT connection of the iBoot-PoE-P to the PoE powered device to be controlled

2. Connect the Net IN connection of the iBoot-PoE-P to the network switch or PoE injector

Auto Configuration can also be initiated via the web page setup. See Section 5.5

2.2. Hardware Connections

iBoot-PoE-P supports 10/100/1000 Ethernet using the cable supplied, or other suitable unshielded twisted

pair (Cat 5-6) cabling.

Power is derived from either the PSE, such as a PoE Network Switch or a PoE Injector.

Connect the PoE OUT connector to the PoE Device to be controlled (PD); Camera, Access Point,

Phone, etc.

Connect the PoE IN connector to the PoE Power source (PSE); PoE Switch, Midspan or Injector

Ethernet LED Displays

NET IN connector Green LED indicates Network Activity

Amber LED indicates 1000Mbps Speed

PoE OUT connector Green LED indicates Network Activity

Amber LED indicates PoE-P power is available for the PD

iboot-poe-p_v190422w iBoot-PoE-P Page 6

2.3. Power Connection

Model iBoot-PoE-P

Power is supplied by the Power Source Equipment (PSE) on the NET IN connector. No external Power

Supply is necessary.

Voltage Range: 9 –72 VDC

The iBoot-PoE-P supports 802.3af Mode A, Mode B and 4PPoE wiring specifications.

PINS

Mode B

Voltage on Spare Pins

Mode A

Mixed Data and Voltage

4PPoE

(802.3bt Type 3 / 4 Draft D1.2)

Voltage on all pins

DC +

DC -

DC +

DC -

Power Output on the PoE OUT connector will be identical to whatever mode is used on the NET IN connector.

2.4. Mounting Options

iBoot-PoE-P is suitable for desktop, shelf or wall mounting. Two screw holes on the housing can be used

to secure the iBoot-PoE-P to a suitable surface. Insure that the screw heads do not interfere with the

attachment and disconnect of the network cables.

The iBoot-PoE-P is provided with a clip for DIN rail mounting. Two provided screws attach the DIN clip to

the underside of the unit.

iboot-poe-p_v190422w iBoot-PoE-P Page 7

3.Initial Configuration

3.1. DHCP Configuration

If your network supports Dynamic Host Configuration Protocol (DHCP), the iBoot will be automatically

assigned an IP Address and be ready to use. You can discover the IP Address through your

Server/Router, or use Dataprobe’s Device Management Utility (DMU).

If your network does not use DHCP, the iBoot-PoE-P will default to IP Address 192.168.1.254

3.2. Device Management Utility

The DMU is available online at

dataprobe.com/support-iboot-poe/, provides the

easiest means to find and configure your iBoot-PoE-

P for use. It can:

Discover all the iBoots on your network,

Display the current IP address of each device

Allow setting of an IP address

Reset to Factory Defaults

Upgrade the Firmware of the iBoot-PoE-P

Obtain and use the DMU

1. Download the latest version of the DMU at

dataprobe.com/support-iboot-poe/ Run

DMUSetup.exe

2. Run the DMU

Note: The IP address can only be set within the first

two minutes of powering up the iBoot-PoE-P or

pressing the reset button (see Section 12). The

DMU will only work with iBoots on the same physical

subnet as the PC.

Once the DMU is run, click on Device | Discover to

display all the iBoots on your local network. The

DMU will display the Location Name of the iBoot, The

product ID and Version Number, the current IP

Address, and the MAC Address. Factory defaulted

iBoots will display with the name iBoot-PoE-P-xxxx

and have the factory default IP address of

192.168.1.254, or as set by DHCP.

The IP address field also indicates the port for web

access that is used by the iBoot-PoE-P. The

standard port for web browser control is factory

default Port 80.

DMU Discovers Dataprobe Devices

on your Network

Enter New IP Address for iBoot-PoE-P

iboot-poe-p_v190422w iBoot-PoE-P Page 8

Change the IP Address

1. Click on the row containing the iBoot-PoE-P to be set. The row will become highlighted.

2. From the menu select Set | Network Settings

3. Select Static from the IP Mode box to manually enter the Address settings

4. Enter the new IP Address, Subnet Mask, Gateway and DNS addresses into the form.

5. Click OK when done.

6. A confirmation box is displayed. Click OK to clear the box.

Once the IP Address is set, all other operational features of the iBoot-PoE-P can be set up. Click on

Discover again to refresh the display, highlight the desired iBoot-PoE-P and click on Manage | Launch

Browser. See Section 5 to configure the iBoot.

The DMU can also be used to return an iBoot-PoE-P to its Factory Default condition. This can be used to

recover an iBoot-PoE-P with a lost password. Highlight an iBoot-PoE-P from the display and select Set |

Factory Defaults. This must be done within the first two minutes of powering up the iBoot or pressing the

reset button.

Get all the details on the DMU at http://dataprobe.com/support-dmu/

3.3. Other ways to set the IP Address

1. Web Browser via the Set-up Page –See Section 5

2. Command Line Interface See Section 9

3.4. Automatic Configuration

Automatic Configuration provides the quickest and easiest way to get your iBoot-PoE-P up and running. It

diagnoses the installation environment and pre-sets the Automation section based on the application. The

iBoot-PoE-P will self-configure for automatic reboot under the following conditions:

Factory New Install

Factory Reset Install See Section 12

Manually enabling Auto Configure from the Automation web page

Manually enabling Auto Configure from the CLI command

The steps the iBoot-PoE-P uses for Auto Configuration are as follows

1. Establish IP credentials on the network using DHCP (if not already established)

2. Listen on the OUT connector for activity for up to 30 seconds

3. Set either the AutoPing or Traffic Monitor active

oSet AutoPing if only 1 IP Address is discovered

This would be typical of a camera, phone or security system installation

oSet Traffic Monitor if multiple IP Addresses are discovered

This would be typical of an access point application

iboot-poe-p_v190422w iBoot-PoE-P Page 9

The following are the standard settings that will be used for self-configuring AutoPing and Traffic Monitor.

All these settings can be changed with either the web setup or Command Line Interface. See Section 5.5

for an explanation of these settings.

AutoPing Setting

Address: IP Address of Powered Device

Frequency: 10 Seconds

Fail Count: 3

Mode: Single

Action: Cycle

Restart: 10 Seconds

Traffic Monitor Settings

Fail Time 10 Seconds

Restart Time 10 Seconds

Number of Cycles 1

Minimum Traffic 0 Kbps

Monitoring: Uplink only

Max Bandwidth Test: Disabled

Daily Disable: Disabled

iboot-poe-p_v190422w iBoot-PoE-P Page 10

4.Web Browser Operation

4.1. Password Protection

iBoot-PoE-P uses two username/password credential sets,

one for power control only (User) and one that also provides

access to the setup functions (Admin). This configuration

can be changed to require Administrator credentials at all

times or allow unsecured User level control. See section

5.7.

Default Credentials:

Role

Username (fixed)

Password

(settable)

Administrator

admin

User

user

Open your browser and enter the IP address of iBoot-PoE-P into the address bar. That address will either

be the one assigned by your DHCP server, one that it was manually changed to or the default IP Address

192.168.1.254

Enter the username and password when prompted. When the proper username/password is received the

Control and Status Page is displayed.

iBoot-PoE-P uses an inactivity timer for security. This timeout is user selectable from 0 to 99 minutes.

Setting to zero disables the timeout feature. When there is no activity for the set time in minutes, the user

is automatically logged out and the username and password will need to be entered again for access. This

is to prevent accidental lockout by leaving the user logged in.

As the iBoot-PoE-P allows only one Web user logged in at any time, use caution when disabling

the timeout feature, as it is possible to lock out other users by forgetting to logout. Closing the

browser will not log the user out and will lock out web access. If you do become locked out,

access the iBoot-PoE-P via Telnet and reboot the unit, or press the reset button (see Section 12).

4.2. Mobile Browser Support

The standard web pages illustrated in this manual are for screen sizes

700 pixels wide and greater. For devices with screen widths below 700

pixels, the iBoot-PoE-P uses a set of mobile browser pages. The iBoot-

PoE-P automatically detects the screen size and redirects automatically

to the mobile pages. The mobile pages do not support the setup

functions. To access the setup functions, or to view the full desktop

site, click on the Full Site button.

Table des matières

Autres manuels Dataprobe Changer

Dataprobe

Dataprobe iBoot-G2 Manuel utilisateur

Dataprobe

Dataprobe iBoot-G2S Instructions d'utilisation et d'entretien

Dataprobe

Dataprobe IP-28 Series Manuel utilisateur

Dataprobe

Dataprobe iBoot-DC Manuel utilisateur

Dataprobe

Dataprobe iBoot G2+ Manuel utilisateur

Dataprobe

Dataprobe iBoot-PoE Instructions d'utilisation et d'entretien

Dataprobe

Dataprobe iBoot-30A Manuel utilisateur

Dataprobe

Dataprobe IP-410 - Manuel utilisateur

Dataprobe

Dataprobe iBoot-IO Manuel utilisateur

Dataprobe

Dataprobe 4P-MAS Manuel utilisateur

Dataprobe

Dataprobe iBoot-WiFi Manuel utilisateur

Dataprobe

Dataprobe 8P-MAS Manuel utilisateur

Dataprobe

Dataprobe iBoot-G2 Manuel utilisateur

Dataprobe

Dataprobe RSS-16 Manuel du propriétaire

Dataprobe

Dataprobe iBoot-DC Manuel utilisateur

Dataprobe

Dataprobe K-AB-D25 Manuel du propriétaire

Dataprobe

Dataprobe iBoot-G2S Manuel utilisateur

Dataprobe

Dataprobe iBoot-G2 Manuel utilisateur

Dataprobe

Dataprobe iBoot Manuel utilisateur

Dataprobe

Dataprobe iBoot-G2 Manuel utilisateur

Dataprobe

Dataprobe iBootBar iBB-DC8 Manuel du propriétaire

Dataprobe

Dataprobe iBoot-G2 Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Dataprobe iBoot PoE-P Instructions d'utilisation et d'entretien

Manuels Changer populaires d'autres marques