Danfoss VLT 6000 Manuel utilisateur

READ THESE

INSTRUCTIONS FIRST

VLT®6000 Adjustable Frequency Drive

Option Enclosure

Unpacking and Installation

Instructions

Pub No. 175R5358

May 2000

General

For an option enclosure containing a bypass stored prior to

installation,ensureastoragetemperaturerangebetween

13° F (–25° C) to 149° F (65° C).

Dimensionsforthe 1200 option enclosure, 600 option

enclosureand their associated shipping containersin inches

and millimeters are shown in the table below.

To lessen the possibility of damage, it is recommended that

the option enclosure be located as close to the final

installation site as possible prior to removing the shipping

crate.

thgieHhtdiWhtpeD

mm0021 sissahC sehcni1.97 )mm0102( sehcni2.74 )mm0021( sehcni6.32 )mm006(

mm0021:etarC .ni5.19 )mm4232( ni0.35 )mm6431( .ni0.03 )mm267(

sissahCmm006 sehcni1.97 )mm0102( sehcni6.32 )mm006( sehcni6.32 )mm006(

mm006:etarC .ni5.19 )mm4232( ni0.35 )mm6431( .ni0.03 )mm267(

Option Enclosure Base Installation

A mounting base is provided to secure the option enclosure

intoposition (see figure 1).

1. Assemblemountingbaseinaccordancewith

manufacturer'sinstructions.

2. Do not assemble side access panel of mounting base,

on appropriate side, to allow for electrical cable access

for connection to drive.

3. Ensure that mounting base is level.

Figure 1. 1200 Chassis Mounting Base

23.6

(600)

47.2

(1200)

7.8

(200)

CAUTION

DO NOT lift unit in the following manner.Damage

to casing may result, making front door panels

inoperable.

Proper lifting method

Figure 3. Option Enclosure Lift

Unpacking the Option Enclosure

Removetheoption enclosure shipping crate in accordance

with the following instructions.

1. Remove top panel of crate by prying up metal locking

tabs that secure top panel (see figure 2).This allows

access to lifting rings located on top of option enclosure.

2. Use a forklift or other lifting device to ensure stability of

option enclosure.Position lifting device securely.

3. Use a spreader bar or similar device to distribute weight

evenly on all four lifting rings (see figure 3). Lift option

enclosure several inches to clear crate bottom for

removal.

4. Removeremainingcratepanelsby prying up metal

locking tabs.

CAUTION

Locking tab

Figure 2. Shipping Crate (1200 mm shown)

A forklift or other lifting device with a qualified

operatorisneeded to removetheoption enclosure

from the crate.

Positioning

After unpacking, the enclosure option is ready to be lifted

prior to mounting on the base.

600 Option Enclosure1200 Option Enclosure

79.1

(2010)

47.2

(1200)

23.6

(600)

Bottom Access Panel

23.6

(600) 23.6

(600)

Bottom Access Panel

79.1

(2010)

Observe all warnings and safety precautions as

well as all local electrical codes and the National

Electrical Code (NEC).

WARNING

Bottom Access Panel Removal

The bottom access panel of the option enclosure must be

removed prior to installation to provide access to the

electrical cabling.The bottom panel is divided into sections.

Remove the desired panel sections, as required, by

removing the set screws holding the panel in place. Protect

theelectrical cables and connection wiringagainstdamage

duringinstallation.

Mounting Option Enclosure to Base

Align the holes on the bottom of the option enclosure with

thecorresponding holes on the mountingbase.Fastenthe

enclosuretothe base with the attaching hardwaresupplied

withtheoption enclosure.

Electrical Connections

Wire the option enclosure to theVLT drive in accordance

withthefollowingprocedure.

1. Connectinputpowercables(typicallylabeled 5L1, 5L2,

and 5L3) to drive input power connections R/L1, S/L2,

andT/L3 (terminals 91, 92, and 93).Refer to customer

connectiondiagramfor details.

2. Connectoutputpowercables(typically labeled 2T1, 2T2,

and 2T3) from option to drive output connection U/T1,

V/T2, andW/T3 (terminals 96, 97, and 98).Refer to

customerconnection diagram for details.

3. Connectcontrolwires(providedloose in bottom of option

enclosure) toVLT drive control terminals in accordance

withschematic diagram provided with option.

Connect the drive and option assembly to the building

electrical system in accordance with the following procedure.

1. Connect3-phaseACinputpowertooptionenclosure

terminalsL1,L2,and L3. Connect ground wire to ground

terminalinside of option enclosure.

2. Connect3-phaseACmotorleadstooption enclosure

terminalsT1,T2,andT3.Connectmotor groundto

groundterminalinsideof option enclosure.

3. Connect external control wires to drive and option in

accordancewithcustomerconnectiondiagramprovided

with option.Note that terminal block TB1 (TB2, etc.) is

locatedin option enclosure.

Operating Instructions

Seethe

Installation,Operation and Maintenance Manual

(documentnumber23-6108-00) fortheVLT6000Adjustable

FrequencyDriveforoperatinginstructions.

Danfoss Graham

Division of Danfoss Inc.

8800 West Bradley Road

P.O. Box 245041

Milwaukee, Wisconsin 53224-9541

Phone: 414/355-8800 Fax: 414/355-6117

Toll Free: 800-621-8806

E-mail: [email protected]

Web page: http://www.grahamdrives.com

Autres manuels pour VLT 6000

Autres manuels Danfoss Convertisseur de média

Danfoss

Danfoss VLT 5000 Series Fiche technique

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Mode d’emploi

Danfoss

Danfoss Vacon NXP Instructions d'utilisation

Danfoss

Danfoss FC 100 Manuel utilisateur

Danfoss

Danfoss VLT 3000 Series Manuel utilisateur

Danfoss

Danfoss VLT 2800 Series Manuel utilisateur

Danfoss

Danfoss VLT MCA 121 EtherNet/IP Manuel utilisateur

Danfoss

Danfoss iC7 Series Manuel utilisateur

Danfoss

Danfoss VLT DeviceNet MCA 104 Mode d'emploi

Danfoss

Danfoss VLT Micro Drive FC 51 Series Manuel utilisateur

Danfoss

Danfoss VLT PROFIBUS DP MCA 101 Manuel utilisateur

Danfoss

Danfoss iC7 Series Manuel utilisateur

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Mode d'emploi

Danfoss

Danfoss VLT PROFIBUS DP MCA 101 Manuel utilisateur

Danfoss

Danfoss FC 300 Mode d’emploi

Danfoss

Danfoss VLT Micro Drive Manuel utilisateur

Danfoss

Danfoss 176F4170 Manuel utilisateur

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuel utilisateur

Danfoss

Danfoss VLT AQUA Drive FC 202 Manuel utilisateur

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuel utilisateur

Danfoss

Danfoss iC7 Series Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 300 Manuel utilisateur

Danfoss

Danfoss VLT series Manuel utilisateur

Danfoss

Danfoss FCM 300 Series Mode d’emploi

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur