Danfoss 176F4170 Manuel utilisateur
•
•
•
•
1 Overview
1.1 Description
The ground bar kit provides extra grounding points for iC7 Series Frequency Converters. The kits fit the following frames:
FK09a/FB09a
FK10a/FB10a
FK09c/FB09c
FK10c/FB10c
The frame is listed on the frequency converter product label.
1.2 Kit Numbers
Use these instructions with the following kits.
Table 1: Ground Bar Kit Numbers
Number
Kit description
176F4170
Ground bar kit, FK09a/FB09a
176F4171
Ground bar kit, FK10a/FB10a
176F4186
Ground bar kit, FK09c/FB09c
176F4187
Ground bar kit, FK10c/FB10c
1.3 Items Supplied
The kits contain a ground bar with brackets and fasteners for attaching the ground bar. Most kits contain a single ground bar, ex-
cept kit 176F4186, which has a 2-part split ground bar.
Table 2: Items Supplied in Ground Bar Kits
Item
Quantity
Ground bar
1–2
Left bracket
1
Right bracket
1
Screws
5–6
AN422434236428en-000201 / 136R0288 | 1Danfoss A/S © 2022.10
Installation Guide
Ground Bar Kit for FK09/FB09 and FK10/FB10
iC7 Series Frequency Converters
-
-
-
-
-
-
-
-
-
-
-
2 Installation
2.1 Safety Information
NOTICE
QUALIFIED PERSONNEL
Only qualified personnel are allowed to install the parts described in these installation instructions.
Disassembly and reassembly of the frequency converter must be done in accordance with the corresponding service guide.
Use the standard fastener torque values from the service guide, unless the torque value is specified in these instructions.
WARNING
ELECTRICAL SHOCK HAZARD
The frequency converter contains dangerous voltages when connected to mains voltage. Improper installation, and installing or
servicing with power connected, can cause death, serious injury, or equipment failure.
Only use qualified electricians for the installation.
Disconnect the frequency converter from all power sources before installation or service.
Treat the frequency converter as live whenever the mains voltage is connected.
Follow the guidelines in these instructions and local electrical safety codes.
WARNING
DISCHARGE TIME (20 MINUTES)
The frequency converter contains DC-link capacitors, which can remain charged even when the frequency converter is not pow-
ered. High voltage can be present even when the warning indicator lights are off.
Failure to wait 20 minutes after power has been removed before performing service or repair work can result in death or serious
injury.
Stop the motor.
Disconnect AC mains, permanent magnet type motors, and remote DC-link supplies, including battery back-ups, UPS, and
DC-link connections to other frequency converters.
Wait 20 minutes for the capacitors to discharge fully before performing any service or repair work.
Measure the voltage level to verify full discharge.
NOTICE
ELECTROSTATIC DISCHARGE
Electrostatic discharge can damage components.
Ensure discharge before touching internal frequency converter components, for example by touching a grounded, conduc-
tive surface or by wearing a grounded armband.
AN422434236428en-000201 / 136R02882 | Danfoss A/S © 2022.10
Installation
Ground Bar Kit for FK09/FB09 and FK10/FB10
Installation Guide
1.
2.
2.2 Replacing the Side Brackets
Before installing the ground bar, use the following steps to replace the existing brackets with the brackets from the kit.
Remove the existing side brackets by removing 2 screws (T25) from the cabinet exterior, 1 from the left bracket and 1 from
the right bracket. See Illustration 1.
e30bk197.10
Illustration 1: Removal of Existing Side Brackets
Attach the new left bracket by fastening 1 M5x12 screw (T25) through the side panel of the cabinet and into the bracket.
Repeat for the right bracket.
The left and right brackets differ from each other. See Illustration 2 for the positioning of each bracket.
AN422434236428en-000201 / 136R0288 | 3Danfoss A/S © 2022.10
Installation
Ground Bar Kit for FK09/FB09 and FK10/FB10
Installation Guide
1.
e30bk198.10
Illustration 2: Installation of Left and Right Brackets
2.3 Installing the Single Ground Bar
For kits with a single ground bar, use the following steps to install the ground bar. See Illustration 3.
For kits with a 2-piece split ground bar, refer to 2.4 Installing the Split Ground Bar.
Attach the ground bar to the 2 brackets by fastening 2 M5x12 screws (T25), 1 in each end of the ground bar.
AN422434236428en-000201 / 136R02884 | Danfoss A/S © 2022.10
Installation
Ground Bar Kit for FK09/FB09 and FK10/FB10
Installation Guide
2.
1.
Fasten 1 M5x12 screw (T25) in the center of the ground bar, attaching it to the lower EMC shield.
T25
e30bk199.10
T25
T25
Illustration 3: Installation of Single Ground Bar (FK09a/FB09a, FK10a/FB10a, FK10c/FB10c)
2.4 Installing the Split Ground Bar
For kits with a 2-part split ground bar, use the following steps to attach the left and right sections of the ground bar.
Attach the left ground bar between the left side bracket and the EMC shield using 2 M5x18 screws (T25), 1 in each end of
the ground bar.
The right ground bar attaches to the EMC shield just below the position of the left ground bar. See Illustration 4.
AN422434236428en-000201 / 136R0288 | 5Danfoss A/S © 2022.10
Installation
Ground Bar Kit for FK09/FB09 and FK10/FB10
Installation Guide
2.
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
drives.danfoss.com
Any information, including, but not limited to information on selection of product, its application or use, product design, weight, dimensions, capacity or any other tech-
nical data in product manuals, catalogues descriptions, advertisements, etc. and whether made available in writing, orally, electronically, online or via download, shall be
considered informative, and is only binding if and to the extent, explicit reference is made in a quotation or order confirmation. Danfoss cannot accept any responsibility
for possible errors in catalogues, brochures, videos and other material. Danfoss reserves the right to alter its products without notice. This also applies to products or-
dered but not delivered provided that such alterations can be made without changes to form, fit or function of the product. All trademarks in this material are property of
Danfoss A/S or Danfoss group companies. Danfoss and the Danfoss logo are trademarks of Danfoss A/S. All rights reserved.
*136R0288*
*M0037401*
Attach the right ground bar between the EMC shield and the right side bracket using 2 M5x18 screws (T25), 1 in each end of
the ground bar.
T25
T25
T25
T25
e30bk369.10
Illustration 4: Installation of Split Ground Bar (FK09c/FB09c)
AN422434236428en-000201 / 136R02886 | Danfoss A/S © 2022.10
Installation
Ground Bar Kit for FK09/FB09 and FK10/FB10
Installation Guide
Ce manuel convient aux modèles suivants
3
Table des matières
Autres manuels Danfoss Convertisseur de média
Danfoss
Danfoss FC 100 Manuel utilisateur
Danfoss
Danfoss VLT Micro Drive FC 51 Series Manuel utilisateur
Danfoss
Danfoss VLT 6000 Fiche technique
Danfoss
Danfoss VLT series Manuel utilisateur
Danfoss
Danfoss VLT HVAC Drive FC 102 Manuel utilisateur
Danfoss
Danfoss VLT Manuel utilisateur
Danfoss
Danfoss VLT AQUA Drive Series Mode d’emploi
Danfoss
Danfoss VLT 2800 Series Manuel utilisateur
Danfoss
Danfoss VLT 3000 Series Manuel de référence
Danfoss
Danfoss VLT HVAC Drive FC 102 Manuel utilisateur
Danfoss
Danfoss iC7 Series Manuel utilisateur
Danfoss
Danfoss VLT HVAC Basic Drive FC 101 Mode d’emploi
Danfoss
Danfoss VLT FC 103 Manuel utilisateur
Danfoss
Danfoss VLT PROFIBUS DP MCA 101 Manuel utilisateur
Danfoss
Danfoss VLT HVAC Drive FC 102 Manuel utilisateur
Danfoss
Danfoss VLT Midi Drive FC 280 Manuel utilisateur
Danfoss
Danfoss iC7 Series Manuel utilisateur
Danfoss
Danfoss MCA 124 Manuel utilisateur
Danfoss
Danfoss iC7 Series Manuel utilisateur
Danfoss
Danfoss VLT HVAC Drive Metasys N2 Manuel utilisateur
