Danfoss DHP-H Manuel utilisateur

Electrical

installation instructions

Danfoss Heat Pumps

DHP-H

VWBMF302

DHP-H

Electrical installation – Page 2 VWBMF302

Contents

DHP-H 4, 400V 3N .....................................3–5

DHP-H 6, 400V 3N .....................................6–8

DHP-H 8, 400V 3N ................................... 9-11

DHP-H 10, 400V 3N..............................12–14

DHP-H 12, 400V 3N..............................15–17

DHP-H 16, 400V 3N..............................18–20

DHP-H 4 SP, 230V 1N...........................21–23

DHP-H 6 SP, 230V 1N...........................24–26

DHP-H 8 SP, 230V 1N............................27-29

DHP-H 10 SP, 230V 1N.........................30–32

DHP-H 12 SP, 230V 1N.........................33–35

DHP-H Opti Pro 6, 230V 1N...............36–39

DHP-H Opti Pro 8, 230V 1N...............40–43

DHP-H Opti Pro 10, 230V 1N ............44–47

DHP-H Opti Pro 12, 230V 1N ............48–51

Electrical installation

Danfoss heat pumps are factory-wired internally. The leads that are to

be connected are the mains supply (5-wire DPH or 3-wire DPH SP), out-

door temperature sensor and room sensors (if any).

• All electrical wiring must be carried out by a certified electrician in

compliance with local and national codes and regulations. When in

doubt, contact the local electricity distributor.

• The mains lead is passed through the top of the unit.

• Remove the front panel to get access to the terminal blocks. Connect

the mains lead to the terminal block according to the accompanying

schematic diagram.

• The connection of the heat pump to the mains supply must be hard-

wired and a multi-pole switch

(safety switch) must be installed in the power supply line to the unit.

WARNING! To disconnect the power supply to the heat pump, the

safety switch must be switched off.

NOTE! The cables to the outdoor and indoor sensors carry low voltage.

Interference from surrounding cables may affect these and cause incor-

rect information to be sent to the control unit. It is therefore vitally

important that careful consideration be given to positioning of cables.

Low-voltage cables must be kept well separated from high-voltage

cables. It is important that low-voltage cables are run parallel to high-

voltage cables and separated by a distance of at least 25 cm for cable

lengths up to 100 m. For longer cable lengths, the distance between

cables should be increased.

Important information

Before switching on the power supply to the heat pump, you must

ensure that the heating system, chilled water line and hot water heater

are filled and vented. Otherwise, the circulation pumps can be severely

damaged.

DHP-H

Electrical installation – Page 3

VWBMF302

DHP-H

Electrical installation – Page 4 VWBMF302

DHP-H

Electrical installation – Page 5

VWBMF302

DHP-H

Electrical installation – Page 6 VWBMF302

DHP-H

Electrical installation – Page 7

VWBMF302

DHP-H

Electrical installation – Page 8 VWBMF302

DHP-H

Electrical installation – Page 9

VWBMF302

DHP-H

Electrical installation – Page 10 VWBMF302

Autres manuels pour DHP-H

3

Autres manuels Danfoss Pompe à chaleur

Danfoss

Danfoss DHP-AQ Mini Mode d'emploi

Danfoss

Danfoss DHP-R 26 Manuel utilisateur

Danfoss

Danfoss BW10 020-090 Manuel

Danfoss

Danfoss Optyma Slim Pack OP-LSQM Series Manuel utilisateur

Danfoss

Danfoss OPTYMA Plus OP-LPQM Manuel utilisateur

Danfoss

Danfoss Optyma OP-MCRN030 Manuel utilisateur

Danfoss

Danfoss Optyma Slim Pack OP-LPQE Series Manuel utilisateur

Danfoss

Danfoss DHP-iQ Mini Guide de l'utilisateur

Danfoss

Danfoss Optyma Series Manuel utilisateur

Danfoss

Danfoss DHP-AQ Manuel utilisateur

Danfoss

Danfoss DHP-S&DP Manuel utilisateur

Danfoss

Danfoss Optyma iCO2 Manuel utilisateur

Danfoss

Danfoss OPTYMA PLUS OP-LPHM Manuel utilisateur

Danfoss

Danfoss DHP-AX Guide rapide

Danfoss

Danfoss Optyma Plus Manuel utilisateur

Danfoss

Danfoss DHP-iQ Manuel utilisateur

Danfoss

Danfoss DHP-H Varius Pro+ Guide de l'utilisateur

Danfoss

Danfoss Optyma OP-LPQE Series Manuel utilisateur

Danfoss

Danfoss OPTYMA Plus OP-LPQM Manuel utilisateur

Danfoss

Danfoss ECL Comfort 100M Manuel utilisateur

Danfoss

Danfoss DHP-AX Manuel utilisateur

Danfoss

Danfoss Bluestar Series Manuel utilisateur

Danfoss

Danfoss DHP-AX 6 Manuel utilisateur

Danfoss

Danfoss Optyma Slim Pack OP-LSHM Series Manuel utilisateur

Manuels Pompe à chaleur populaires d'autres marques

MICROWELL

MICROWELL HP 1000 GREEN Manuel utilisateur

Sanyo

Sanyo SAP120FCH Manuel utilisateur

Daikin

Daikin EHYHBH05AA Manuel utilisateur

Panasonic

Panasonic WH-SDF03E3E5 Mode d’emploi

Bryant

Bryant 544B Manuel utilisateur

Airxcel

Airxcel 45000 Series Manuel

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manuel utilisateur

Dimplex

Dimplex LI 16I-TUR Guide de l'utilisateur

Carrier

Carrier WSHP Open v3 Guide de configuration rapide

TGM

TGM CTV14CN018A Manuel utilisateur

Carrier

Carrier 38MGQ Series Manuel utilisateur

Kokido

Kokido K2O K880BX/EU Guide de dépannage

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guide rapide

Carrier

Carrier 48EZN Manuel utilisateur

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Mode d'emploi

Ariston

Ariston NIMBUS Manuel utilisateur

Weishaupt

Weishaupt WWP L 7 Guide de l'utilisateur

GE

GE Zoneline AZ85H09EAC Manuel utilisateur