Danfoss FC 300 Mode d’emploi

Contents

How to Read this Design Guide

How to Read this Design Guide 5

Approvals 5

Symbols 6

Abbreviations 6

Definitions 7

Introduction to FC 300

Disposal Instruction 13

Software Version 13

Air Humidity 15

Aggressive Environments 15

Vibration and Shock 16

Control Principle 17

FC 300 Controls 17

FC 301 vs. FC 302 Control Principle 17

Control Structure in VVCplus 18

Control Structure in Flux Sensorless (FC 302 only) 19

Control Structure in Flux with Motor Feedback 19

Internal Current Control in VVC+ Mode 20

Local (Hand On) and Remote (Auto On) Control 21

Reference Handling 23

Scaling of References and Feedback 24

Dead Band Around Zero 24

Speed PID Control 29

The following parameters are relevant for the Speed Control 29

Process PID Control 31

Ziegler Nichols Tuning Method 35

EMC Test Results (Emission, Immunity) 37

EMC Immunity 38

Earth Leakage Current 40

Selection of Brake Resistor 40

Control of Mechanical Brake 42

Safe Stop of FC 300 45

Safe Stop Installation (FC 302 and FC 301 - A1 enclosure only) 46

Safe Stop Commissioning Test 47

FC 300 Selection

Electrical Data 49

General Specifications 53

Efficiency 58

Acoustic Noise 58

Peak Voltage on Motor 59

Derating for Installing Long Motor Cables or Cables with Larger Cross-Sec-

tion 60

FC 300 Design Guide

MG.33.B7.02 - VLT is a registered Danfoss trademark 1

How to Order

Drive Configurator 63

Ordering Form Type Code 63

Ordering Numbers 65

How to Install

Mechanical Dimension 71

Mechanical Installation 73

Accessory Bag 73

Electrical Installation 76

Removal of Knockouts for Extra Cables 76

Connection to Mains and Earthing 77

Motor Connection 79

Fuses 81

Access to Control Terminals 83

Control Terminals (FC 301) 83

Electrical Installation , Control Terminals 84

Basic Wiring Example 84

Electrical Installation , Control Cables 85

Motor Cables 86

Switches S201, S202, and S801 87

Final Set-Up and Test 88

Additional Connections 90

Relay Connection 91

Relay Output 92

Parallel Connection of Motors 92

Motor Thermal Protection 93

How to Connect a PC to the FC 300 94

The FC 300 Software Dialog 94

Residual Current Device 99

Application Examples

101

Start/Stop 101

Pulse Start/Stop 101

Potentiometer Reference 102

Encoder Connection 102

Encoder Direction 102

Closed Loop Drive System 103

Programming of Torque Limit and Stop 103

Smart Logic Control Programming 104

How to Programme

107

The Graphical and Numerical Local Control Panels 107

How to Programme on the Graphical Local Control Panel 107

The LCD-Display 108

Quick Transfer of Parameter Settings 110

Display Mode 111

FC 300 Design Guide

2MG.33.B7.02 - VLT is a registered Danfoss trademark

Display Mode - Selection of Read-Outs 111

Parameter Set-Up 112

Quick Menu Key Functions 112

Main Menu Mode 115

Parameter Selection 115

Changing Data 115

Changing a Text Value 116

Changing a Group of Numeric Data Values 116

Infinitely Variable Change of Numeric Data Value 116

Changing of Data Value , Step-by-Step 117

Read-out and Programming of Indexed Parameters 117

How to Programme on the Numerical Local Control Panel 118

Local Control Keys 119

Initialisation to Default Settings 120

Parameter Selection - FC 300 121

Parameters: Operation and Display 122

Parameters: Load and Motor 132

Parameters: Brakes 146

Parameters: Reference/Ramps 150

Parameters: Limits/Warnings 160

Parameters: Digital In/Out 165

Parameters: Analog In/Out 178

Parameters: Controllers 184

Parameters: Communications and Options 188

Parameters: Profibus 194

Parameters: DeviceNet CAN Fieldbus 200

Parameters: Smart Logic Control 205

Parameters: Special Functions 217

Parameters: Drive Information 223

Parameters: Data Read-outs 229

Parameters: EncoderInput 236

Parameter Lists 239

Options and Accessories

261

Options and Accessories 261

Mounting of Option Modules in Slot B 261

General Purpose Input Output Module MCB 101 261

Encoder Option MCB 102 263

Resolver Option MCB 103 265

Relay Option MCB 105 267

24 V Back-Up Option MCB 107 (Option D) 270

IP 21/IP 4X/ TYPE 1 Enclosure Kit 271

LC Filters 271

RS-485 Installation and Set-up

273

RS-485 Installation and Set-up 273

FC Protocol Overview 276

Network Configuration 276

FC 300 Design Guide

MG.33.B7.02 - VLT is a registered Danfoss trademark 3

FC Protocol Message Framing Structure - FC 300 277

Examples 282

Danfoss FC Control Profile 282

Troubleshooting

293

Status messages - FC 300 DG 293

Index

300

FC 300 Design Guide

4MG.33.B7.02 - VLT is a registered Danfoss trademark

How to Read this Design Guide

This Design Guide will introduce all aspects of your FC 300.

Available literature for FC 300

-The VLT®AutomationDrive FC 300 Operating Instructions MG.33.AX.YY provide the neccessary

information for getting the drive up and running.

-The VLT®AutomationDrive FC 300 Design Guide MG.33.BX.YY entails all technical information

about the drive and customer design and applications.

-The VLT®AutomationDrive FC 300 Profibus Operating Instructions MG.33.CX.YY provide the in-

formation required for controlling, monitoring and programming the drive via a Profibus fieldbus.

-The VLT®AutomationDrive FC 300 DeviceNet Operating Instructions MG.33.DX.YY provide the

information required for controlling, monitoring and programming the drive via a DeviceNet

fieldbus.

X = Revision number

YY = Language code

Danfoss Drives technical literature is also available online at www.danfoss.com/BusinessAreas/Drives-

Solutions/Documentations/Technical+Documentation.

Approvals

FC 300 Design Guide

MG.33.B7.02 - VLT is a registered Danfoss trademark 5

Symbols

Symbols used in this Design Guide.

NB!

Indicates something to be noted by the reader.

Indicates a general warning .

Indicates a high-voltage warning.

*Indicates default setting

Abbreviations Alternating current AC

American wire gauge AWG

Ampere/AMP A

Automatic Motor Adaptation AMA

Current limit ILIM

Degrees Celcius °C

Direct current DC

Drive Dependent D-TYPE

Electro Magnetic Compellability EMC

Electronic ThermAL Relay ETR

Frequency Converter FC

Gram g

Hertz Hz

Kilohertz kHz

Local Control Panel LCP

Meter m

Milli Henry Inductance mH

Milliampere mA

Millisecond ms

Minute min

Motion Control Tool MCT

Motor Type Dependent M-TYPE

Nanofarad nF

Newton Meters Nm

Nominal motor current IM,N

Nominal motor frequency fM,N

Nominal motor power PM,N

Nominal motor voltage UM,N

Parameter par.

Protective Extra Low Voltage PELV

Printed Circuit Board PCB

Rated Inverter Output Current IINV

Revolutions Per Minute RPM

Second s

Torque limit TLIM

Volts V

FC 300 Design Guide

How to Read this Design Guide

6MG.33.B7.02 - VLT is a registered Danfoss trademark

Definitions

Drive:

D-TYPE

Size and type of the connected drive (dependencies).

IVLT,MAX

The maximum output current.

IVLT,N

The rated output current supplied by the frequency converter.

UVLT, MAX

The maximum output voltage.

Input:

Control command

You can start and stop the connected motor by

means of LCP and the digital inputs.

Functions are divided into two groups.

Functions in group 1 have higher priority than

functions in group 2.

Group 1 Reset, Coasting stop, Reset and

Coasting stop, Quick-stop, DC

braking, Stop and the "Off" key.

Group 2 Start, Pulse start, Reversing,

Start reversing, Jog and Freeze

output

Motor:

fJOG

The motor frequency when the jog function is activated (via digital terminals).

The motor frequency.

fMAX

The maximum motor frequency.

fMIN

The minimum motor frequency.

fM,N

The rated motor frequency (nameplate data).

The motor current.

IM,N

The rated motor current (nameplate data).

M-TYPE

Size and type of the connected motor (dependencies).

nM,N

The rated motor speed (nameplate data).

PM,N

The rated motor power (nameplate data).

TM,N

The rated torque (motor).

The instantaneous motor voltage.

FC 300 Design Guide

How to Read this Design Guide

MG.33.B7.02 - VLT is a registered Danfoss trademark 7

UM,N

The rated motor voltage (nameplate data).

Break-away torque

!VLT

The efficiency of the frequency converter is defined as the ratio between the power output and the power

input.

Start-disable command

A stop command belonging to the group 1 control commands - see this group.

Stop command

See Control commands.

References:

Analog Reference

A signal transmitted to the analog input s 53 or 54, can be voltage or current.

Binary Reference

A signal transmitted to the serial communication port.

Preset Reference

A defined preset reference to be set from -100% to +100% of the reference range. Selection of eight

preset references via the digital terminals.

Pulse Reference

A pulse frequency signal transmitted to the digital inputs (terminal 29 or 33).

RefMAX

Determines the relationship between the reference input at 100% full scale value (typically 10 V, 20mA)

and the resulting reference. The maximum reference value set in par. 3-03.

RefMIN

Determines the relationship between the reference input at 0% value (typically 0V, 0mA, 4mA) and the

resulting reference. The minimum reference value set in par. 3-02.

Miscellaneous:

Analog Inputs

The analog inputs are used for controlling various functions of the frequency converter.

There are two types of analog inputs:

Current input, 0-20 mA and 4-20 mA

Voltage input, 0-10 V DC (FC 301)

Voltage input, -10 - +10 V DC (FC 302).

Analog Outputs

The analog outputs can supply a signal of 0-20 mA, 4-20 mA, or a digital signal.

FC 300 Design Guide

How to Read this Design Guide

8MG.33.B7.02 - VLT is a registered Danfoss trademark

Automatic Motor Adaptation, AMA

AMA algorithm determines the electrical parameters for the connected motor at standstill.

Brake Resistor

The brake resistor is a module capable of absorbing the brake power generated in regenerative braking.

This regenerative braking power increases the intermediate circuit voltage and a brake chopper ensures

that the power is transmitted to the brake resistor.

CT Characteristics

Constant torque characteristics used for all applications such as conveyor belts, displacement pumps and

cranes.

Digital Inputs

The digital inputs can be used for controlling various functions of the frequency converter.

Digital Outputs

The drive features two Solid State outputs that can supply a 24 V DC (max. 40 mA) signal.

DSP

Digital Signal Processor.

ETR

Electronic Thermal Relay is a thermal load calculation based on present load and time. Its purpose is to

estimate the motor temperature.

Hiperface®

Hiperface®is a registered trademark by Stegmann.

Initialising

If initialising is carried out (par. 14-22), the frequency converter returns to the default setting.

Intermittent Duty Cycle

An intermittent duty rating refers to a sequence of duty cycles. Each cycle consists of an on-load and an

off-load period. The operation can be either periodic duty or none-periodic duty.

LCP

The Local Control Panel (LCP) makes up a complete interface for control and programming of the FC 300

Series. The control panel is detachable and can be installed up to 3 metres from the frequency converter,

i.e. in a front panel by means of the installation kit option.

lsb

Least significant bit.

msb

Most significant bit.

MCM

Short for Mille Circular Mil, an American measuring unit for cable cross-section. 1 MCM = 0.5067 mm2.

On-line/Off-line Parameters

Changes to on-line parameters are activated immediately after the data value is changed. Changes to

off-line parameters are not activated until you enter [OK] on the LCP.

Process PID

The PID regulator maintains the desired speed, pressure, temperature, etc. by adjusting the output fre-

quency to match the varying load.

FC 300 Design Guide

How to Read this Design Guide

MG.33.B7.02 - VLT is a registered Danfoss trademark 9

Pulse Input/Incremental Encoder

An external, digital pulse transmitter used for feeding back information on motor speed. The encoder is

used in applications where great accuracy in speed control is required.

RCD

Residual Current Device.

Set-up

You can save parameter settings in four Set-ups. Change between the four parameter Set-ups and edit

one Set-up, while another Set-up is active.

SFAVM

Switching pattern called Stator Flux oriented Asynchronous Vector Modulation (par. 14-00).

Slip Compensation

The frequency converter compensates for the motor slip by giving the frequency a supplement that fol-

lows the measured motor load keeping the motor speed almost constant..

Smart Logic Control (SLC)

The SLC is a sequence of user defined actions executed when the associated user defined events are

evaluated as true by the SLC. (Parameter group 13-xx).

Thermistor :

A temperature-dependent resistor placed where the temperature is to be monitored (frequency converter

or motor).

Trip

A state entered in fault situations, e.g. if the frequency converter is subject to an over-temperature or

when the frequency converter is protecting the motor, process or mechanism. Restart is prevented until

the cause of the fault has disappeared and the trip state is cancelled by activating reset or, in some cases,

by being programmed to reset automatically. Trip may not be used for personal safety.

Trip Locked

A state entered in fault situations when the frequency converter is protecting itself and requiring physical

intervention, e.g. if the frequency converter is subject to a short circuit on the output. A locked trip can

only be cancelled by cutting off mains, removing the cause of the fault, and reconnecting the frequency

converter. Restart is prevented until the trip state is cancelled by activating reset or, in some cases, by

being programmed to reset automatically. Trip may not be used for personal safety.

VT Characteristics

Variable torque characteristics used for pumps and fans.

VVCplus

If compared with standard voltage/frequency ratio control, Voltage Vector Control (VVCplus) improves the

dynamics and the stability, both when the speed reference is changed and in relation to the load torque.

60° AVM

Switching pattern called 60°Asynchronous Vector Modulation (par. 14-00).

Power Factor

The power factor is the relation between I1and

IRMS.

Power factor

xU xI

xcos

xU xI

RMS

The power factor for 3-phase control:

xcos

ϕ1

RMS

since cos

ϕ1=1

The power factor indicates to which extent the

frequency converter imposes a load on the mains

supply .

The lower the power factor, the higher the IRMS for

the same kW performance.

FC 300 Design Guide

How to Read this Design Guide

10 MG.33.B7.02 - VLT is a registered Danfoss trademark

Autres manuels pour FC 300

Table des matières

Autres manuels Danfoss Entraînement CC

Danfoss

Danfoss VLT Brake Resistor MCE 101 Mode d’emploi

Danfoss

Danfoss FCM 300 Series Fiche technique

Danfoss

Danfoss VLT 6000 HVAC Manuel utilisateur

Danfoss

Danfoss E3h Manuel utilisateur

Danfoss

Danfoss CDS 803 Manuel utilisateur

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuel utilisateur

Danfoss

Danfoss MCA 122 Modbus TCP Manuel utilisateur

Danfoss

Danfoss VLT HVAC Drive FC 100 Series Mode d’emploi

Danfoss

Danfoss VLT AutomationDrive FC 300 Mode d'emploi

Danfoss

Danfoss VLT series Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 300 Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 300 Mode d’emploi

Danfoss

Danfoss RAVV Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 300 Mode d’emploi

Danfoss

Danfoss VLT AutomationDrive FC 301 Mode d’emploi

Danfoss

Danfoss VLT DriveMotor FCP 106 Manuel utilisateur

Danfoss

Danfoss vlt aqua Manuel utilisateur

Danfoss

Danfoss VLT HVAC Basic Drive FC 101 Manuel utilisateur

Danfoss

Danfoss VLT AQUA Drive FC 202 Manuel utilisateur

Danfoss

Danfoss VACON 3000 Guide de l'utilisateur

Danfoss

Danfoss VLT AQUA Drive FC 202 Manuel utilisateur

Danfoss

Danfoss VLT HVAC Drive FC 102 Manuel utilisateur

Danfoss

Danfoss vlt aqua Mode d’emploi

Danfoss

Danfoss VLT FC Series Manuel utilisateur

Manuels Entraînement CC populaires d'autres marques

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces

Chamberlain Garog

Chamberlain Garog D Series Manuel utilisateur

Parker

Parker PDS Series Manuel utilisateur

Festo

Festo DGC G Series Guide de configuration

Binks

Binks QS-5012-1-CE Manuel utilisateur

ABB

ABB ACQ580-01 Series Manuel d'installation

YASKAWA

YASKAWA CANopen SI-S3 Manuel utilisateur

GE D20A6 Manuel utilisateur

Unex

Unex MC-D-250-1000-050W-TW Manuel utilisateur

Geckodrive

Geckodrive G213V Manuel utilisateur

ABB

ABB RSYC-01 Manuel utilisateur

Rockwell Automation

Rockwell Automation PowerFlex 700S Manuel du propriétaire

WEG

WEG DeviceNet CFW500 Manuel utilisateur

Siemens

Siemens SINAMICS G Fiche technique

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Mode d'emploi

SOMFY

SOMFY JR RU 30 Manuel utilisateur

Beckhoff

Beckhoff AX8911 Manuel de l'opérateur