Danfoss MMIGRS2 Manuel utilisateur
520H9703
520H9703
Installation Guide
MCX rooftop controller
Instruction guide
DKRCC.PI.RI0.L1.22 / 520H9703 | 1
© Danfoss | DCS (za) | 2015.08 Installation guide | MCX rooftop controller
DKRCC.PI.RI0.L1.22
520H9703
MCX152V
Ordering no.
080G0304 = 110/230vac
Identication:
Connection:
MCX08M (Optional)
Ordering no.
080G0029 = 110/230vac
MMIGRS2 (Optional)
Ordering no.
080G0294
IP 20
-20 – 60 °C (0 – 140 °F)
RH max. 90% non condensing
CE COMPLIANCE
This product is designed to comply with the following EU standards:
Low voltage guideline: 73/23/EEC Electromagnetic compatibility EMC:
89/336/EEC and with the following norms:
EN61000-6-1, EN61000-6-3 (immunity for residential, commercial and
light-industrial environments)
EN61000-6-2, EN61000-6-4 (immunity and emission standard for
industrial environments)
EN60730 (Automatic electrical controls for household and similar use)
UL APPROVAL
UL file: E31024
®
Supply Voltage
85 – 265 V AC, 50/60 Hz
Maximum power consumption: 27 W, 48 VA
Insulation between power supply and the extra-low
voltage: reinforced
Plugs normally not used
Stepper Motor 1, Stepper Motor 2, Stepper Backup,
RS485-2, Digital Input 18
Modbus
It is important that the installation of the data
communication cable be installed correctly.
Remember to terminate each end of the bus.
See separate literature No. RC8AC.
DO - Digital outputs, 15 pcs. DO1 – DO15
DO1 - DO15, all are relays, no solid state relays
The relays are de-rated to the specified values
AO - Analog output, 6 pcs. AO1 – AO6
Outputs are 0 – 10 V DC by default
AI - Analog Inputs, 14 pcs. AI1 – AI14
All temperature sensors default to PT1000, Pressure
transducers default to 0.5 – 4.5 V DC ratiometric with
5 V DC supply. All other inputs are 0 – 5 V DC by default
DI - Digital switch inputs DI1 – DI17
All Dry contacts except DI17,
(24 V AC or 230 V AC driven)
Technical data:
2 |DKRCC.EI.RL0.I1.02 / 520H9646 © Danfoss | DCS (za) | 2015.08Installation guide | MCX rooftop controller
110 mm - 4.33 in.
280 mm - 11.02 in. 63 mm - 2.48 in.
Dimensions:
Modbus topology:
AK-SM800:
The cable must be EIA485 rated. The cable is connected from controller to controller, and no branches are allowed on the
cable. If the cable length exceeds 1200 m a repeater must be inserted. One repeater must be added for every 32 controllers.
If the data communication cable runs through an electrically noisy environment which impairs the data signal, one or more
repeaters must be added to stabilise the signal.
When configuring Modbus devices on the control bus, the highest device address that can be used is 124
(max 120 modbus control devices in total - max 45 MCX RTC).
The wires are looped from device to device. A is connected to A and B is connected to B. The screen must be connected to the
system device, all controller and any repeaters. A screen must always be looped from device to device.
The screen must not be connected to anything else.
See AK-SM800 User Guide for system 485 wiring instructions.
Manual can be found at: http://food-retail.danfoss.com/knowledge-center/software/ak-sm-800/
Be sure to configure the Modbus repeater AKA 222 (code#084B2240) to the correct baud rate.
MCX-RTU baud rate must be set to 38.4 K when used with the AK-SM800. MCX-RTU cannot be on the same 485 bus with SLVs.
Termination
Repeater
DKRCC.EI.RL0.I1.02 / 520H9646 | 3© Danfoss | DCS (za) | 2015.08 Installation guide | MCX rooftop controller
Wiring Diagram MCX152V -bottom and top
STEPPER
MOTOR 2
RS485-1
SD/MMC
ST2 4
ST2 3
ST2 2
ST2 1
RS485-2
MEMORY CARD
MCX152V TOP
ANALOG OUTPUT 1-6 ANALOG INPUT 1-7
ANALOG INPUT 8-14
STEPPER
MOTOR 1
ST1 4
ST1 3
ST1 2
ST1 1
AO 6
AO 5
AO 4
COM
AO 3
AO 2
AO 1
COM
COM
COM
15V+
AI 7
AI 6
AI 5
5V+
AI 4
AI 3
AI 2
AI 1
Not used
Damper AO
VS compressors 4
VS compressors 3
Modbus connection
Mixed Air (PT1000)
Outdoor Temp (PT1000)
Fan CT (0 – 5 V DC)
Compr 1 Press (5 V DC)
Compr 2 Press (5 V DC)
Compr 3 Press (5 V DC)
Compr 4 Press (5 V DC)
DP Outside/Mixed Air
Zone CO2(0 – 5 V DC)
Outdoor RH(0 – 5 V DC)
Zone RH(0 – 5 V DC)
Return Air(PT1000)
Supply Air(PT1000)
Zone Temp(PT1000)
COM
COM
15V+
AI 14
AI 13
AI 12
5V+
AI 11
AI 10
AI 9
AI 8
COM 1
D1 +
D1 -
COM 2
D2 +
D2 -
VS compressors 2
VS compressors 1
Fan AO
© Danfoss | DCS (za) | 2015.08
Contact info:
www.danfoss.com
Installation guide | MCX rooftop controller DKRCC.EI.RL0.I1.02 / 520H9646 | 4
DIGITAL INPUT 18 DIGITAL OUTPUT 9-12 DIGITAL OUTPUT 13-15
STEPPER BACKUP DIGITAL INPUT 1-8 DIGITAL INPUT 9-16
POWER
SUPPLY
MCX152V BOTTOM
CANCAN-RJ ETHERNET DIGITAL INPUT 17
COM
CANL
CANH
R120
COM 17
DI 17
DIGITAL OUTPUT 6-8
NO 8
C 8
NO 7
C 7
NO 6
C 6
DIGITAL OUTPUT 1-5
NO 3
C 3
NO 2
C 2
NO 5
C 5
NO 4
C 4
NO 1
C 1
CAN-RJ
ETH
DI 17H
Input Voltage
110 – 230 V AC
Optional IO Expansion
Optional - Remote Display
Not Used
Cool 4 Proof
Aux Heat 4 (N.O.)
Aux Heat 3 (N.O.)
Aux Heat 2 (N.O.)
Aux Heat 1 (N.O.)
Cool 4 (N.O.)
Cool 3 (N.O.)
Cool 2 (N.O.)
Cool 1 (N.O.)
Stepper Backup
NOT USED
Fan Proof
Phase Loss
Shutdown 1
Shutdown 2
Fan Drive Fault
Compr 1 Drive Fault
Compr 2 Drive Fault
Compr 3 Drive Fault
Compr 4 Drive Fault
Filter Clogged Fault
Damper Override
Title 24
Schedule Override
Cool 1 Proof
Cool 2 Proof
Cool 3 Proof
Reheat (N.O.)
Damper (N.O.)
Heat Reclaim 1 (N.O.)
Heat Reclaim 1 (N.O.)
Heat Pump (N.O.)
Fan Low Speed (N.O.)
Fan High Speed (N.C.)
COM
+ BATT
L
N
15V+
COM
DI 9
DI 10
DI 11
DI 12
COM
DI 13
DI 14
DI 15
DI 16
COM
DI 1
DI 2
DI 3
DI 4
COM
DI 5
DI 6
DI 7
DI 8
DI 18H
DI 18
COM 18
C 9
NO 9
C 10
NO 10
C 11
NO 11
C 12
NO 12
C 13
C 13
NO 13
NC 13
C 14
NO 14
NC 14
C 15
NO 15
NC 15
Wiring Diagram MCX152V -bottom and top
Autres manuels pour MMIGRS2
1
Ce manuel convient aux modèles suivants
3
Autres manuels Danfoss Contrôleurs
Danfoss
Danfoss FP975 Manuel utilisateur
Danfoss
Danfoss AME 25 Manuel utilisateur
Danfoss
Danfoss FP715Si Manuel utilisateur
Danfoss
Danfoss EKE 347 Manuel utilisateur
Danfoss
Danfoss AK-CC55 Manuel utilisateur
Danfoss
Danfoss AK-CC 450 Manuel utilisateur
Danfoss
Danfoss AME 35 Manuel utilisateur
Danfoss
Danfoss EKC 102C Manuel utilisateur
Danfoss
Danfoss AME 55 Manuel utilisateur
Danfoss
Danfoss VTL MCD 203 Series Manuel utilisateur
Danfoss
Danfoss Link Hydronic Controller Manuel utilisateur
Danfoss
Danfoss EKA 183A Manuel utilisateur
Danfoss
Danfoss AME 110 NL Manuel utilisateur
Danfoss
Danfoss AK-CC 750 series Manuel utilisateur
Danfoss
Danfoss Saginomiya RGE-Z3R2-7 Manuel utilisateur
Danfoss
Danfoss AVT/VG Manuel utilisateur
Danfoss
Danfoss ECL Comfort 296 Manuel utilisateur
Danfoss
Danfoss 101N0715 Manuel utilisateur
Danfoss
Danfoss MCI 15BP Manuel utilisateur
Danfoss
Danfoss VLT HVAC Drive FC 102 Mode d’emploi
