Danfoss EKA 183A Manuel utilisateur

520H10102

Installation Guide

EKA 183A with Adaptor for ERC21x Controllers

Programming guide

DKRCC.EI.RL0.I2.02 / 520H10102 | 1© Danfoss | DCS (az) | 2015.05 Installation guide | EKA 183A

Components:

ERC 21x Controller EKA 183A Adaptor with cable assembly

Ordering Number: 080G9740

Pack Contents: EKA 183A, Adaptor with cable assembly

PC settings:

Refer to the specic documentation (DKRCC.PD.R1.06.02) for further details.

Instruction for connecting to controller:

Step 1 Step 2

Connect EKA 183A to Adaptor Connect Adaptor cable with the controller

2 |DKRCC.EI.RL0.I2.02 / 520H10102 © Danfoss | DCS (az) | 2015.05Installation guide | EKA 183A

Programming the controller:

EKA 183A is used to copy settings to an ERC21X controller.

It can also be used to copy settings from one ERC controller to another ERC controller of the same type, eg. the same

software version.

Programming steps:

EKA 183A is inserted into the controller.

The controller is connected to the electricity mains.

Steps Illustration Observations and actions

1- ashes

(checking) YELLOW

The LED will ash YELLOW when the programming is

inserted into the controller. Here it is checked whether the

data can be transferred

2 - light up constant

(await press) YELLOW

Shortly afterwards, the LED constant light up YELLOW and

the data transfer can start

3 - to write to the

controller or

to write to the

programming key

GREEN

RED

~ 1 sec

~ 4 sec

- Pressing the button on the top of EKA (1 sec) will transfer

data from the programming key to the controller

(GREEN LED ashes)

- Pressing the button on the top of EKA (4 sec) will transfer

data from the controller to the programming key

(RED LED ashes)

4 - light up constant

(transfer nished) CONSTANT

GREEN

The transfer has nished when the LED light up constant

green

Flashing red-green-red-green-red-green....... = fault.

If there is a fault indication, please check code no.,

SW version and Error code.

Refer to Technical brochure (DKRCC.PD.R1.06.02) for

more details

Note: refer to the speciﬁc documentation (DKRCC.PD.R1.06.02) for further details

Data Transfer:

Two methods (Mode A or Mode B) can be selected for transferring data. Modes may vary based on product and

connected device as in below table.

The default mode is set as ”Mode B”, which can be used for ERC 21X series only.Refer to specic documentation

(DKRCC.PD.R1.06.02) for step by step process to change the Mode for ERC 10X and ERC 11X Series.

Product Type Mode Setting for Programming Key

Plugged in Doking Station Connected to ERC product directly

ERC 10X Series Mode A Not applicable

ERC 11X Series Mode A Not applicable

ERC 21X Series Not applicable Mode B

Autres manuels Danfoss Contrôleurs

Danfoss

Danfoss HFX Series Manuel utilisateur

Danfoss

Danfoss EKC 202A Manuel utilisateur

Danfoss

Danfoss NovoCon Series Manuel utilisateur

Danfoss

Danfoss AK-CC55 Manuel utilisateur

Danfoss

Danfoss VLT AutomationDrive FC 302 Manuel utilisateur

Danfoss

Danfoss MCV105C Manuel utilisateur

Danfoss

Danfoss VLT Micro Drive FC 51 Series Manuel utilisateur

Danfoss

Danfoss AME 130H Manuel utilisateur

Danfoss

Danfoss VLT Micro Drive Manuel utilisateur

Danfoss

Danfoss EKD 316C Colibri Manuel utilisateur

Danfoss

Danfoss EKC 347 Manuel utilisateur

Danfoss

Danfoss W894A Manuel utilisateur

Danfoss

Danfoss AME 110 NL Manuel utilisateur

Danfoss

Danfoss AME 55 Manuel utilisateur

Danfoss

Danfoss PVE 7 Series Manuel utilisateur

Danfoss

Danfoss 101N0715 Manuel utilisateur

Danfoss

Danfoss ECL Comfort 210 Manuel d'instructions d'installation

Danfoss

Danfoss VLT AutomationDrive FC 300 Manuel utilisateur

Danfoss

Danfoss ADAP-KOOL Drive Manuel utilisateur

Danfoss

Danfoss MCD3000 Series Manuel utilisateur

Danfoss

Danfoss AK-CC 460 Manuel utilisateur

Danfoss

Danfoss Vacon NXP Series Manuel utilisateur

Danfoss

Danfoss AMV 25 Manuel utilisateur

Danfoss

Danfoss AMEi 6 iNET Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur