DALCNET DLC1248 Series Guide d'application
DLC1248 multi channel
EASY RGB / EASY TW
Device Manual FW3.0+
Made in Italy
Rev. 201 -08-22
page 1/4
FEATURES
• SEQUENCER+FADER+DIMMER+DRIVER
• DC Input 12-24-48 Vdc
• Command: N.O. push button
• Tunable white control or RGB color control
• Current outputs or voltage outputs for LED strip
• Typical efficiency > 95%
• Adjusting the brightness up to completed off
• Soft start and stop
• Optimized output curve
• Extended temperature range
• 100% Functional test - 5 Years warranty
➔For the whole and updated Device Manual refer to producer's website: http://www.dalcnet.com
Constant current variants (common anode)
Application: (2 channels output): tunable white
Application: (3 channels output): RGB colour
CODE Supply voltage Output Channels Command
DLC1248-2CC350 12÷48V DC 2 x 350mA 2 N.O. push button
DLC1248-2CC500 12÷48V DC 2 x 500mA 2 N.O. push button
DLC1248-2CC700 12÷48V DC 2 x 700mA 2 N.O. push button
DLC1248-3CC350 12÷48V DC 3 x 350mA 3 N.O. push button
DLC1248-3CC500 12÷48V DC 3 x 500mA 3 N.O. push button
DLC1248-3CC700 12÷48V DC 3 x 700mA 3 N.O. push button
Constant voltage variants (common anode)
AppIication (2-channels output): tunable white
Application (3-channels output): RGB colour
CODE Supply voltage Output Channels Command
DLC1248-2CV 12÷48V DC 2 x 1, A max. 2 N.O. push button
DLC1248-3CV 12÷48V DC 3 x 1, A max. 3 N.O. push button
Protections
OTP Over temperature protection
OVP Over voltage protection
UVP Under voltage protection
RVP Reverse polarity protection
IFP Input fuse protection
SCP Short circuit protection
OCP Open circuit protection
CLP Current limit protection
LED DRIVERS
DALC ET S.r.l.
Registered office: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Headquarters: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Tel. + 39 0444 183 80/18 7452 Fax. + 39 0444 18 7453
VAT: IT-04023100235
info@dalcnet.com www.dalcnet.com
DLC1248 multi channel
EASY RGB / EASY TW
Device Manual FW3.0+
Made in Italy
Rev. 201 -08-22
page 2/4
Reference standards
EN 613 7-1:2008+A1:2011+A2:2013 Lamp controlgear - Part 1: General and safety requirements
EN 61000-3-2:201 Electromagnetic compatibility (EMC) - Part 3-2: Limits - Limits for harmonic current emissions
(equipment input current ≤ 16 A per phase)
EN 61000-3-3:2013 Electromagnetic compatibility (EMC) - Part 3-3: Limits - Limitation of voltage changes, voltage
fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤
16 A per phase and not subject to conditional connection
EN 6238 :2006+A1:2009 DC or AC supplied electronic control gear for LED modules - Performance requirements
EN 55015:2013+A1:2015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting
and similar equipment
EN 615 7:2009 Equipment for general lighting purposes - EMC immunity requirements
EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect
to the restriction of hazardous substances
Technical Specifications
Variants
Constant current Constant voltage
2 channels 3 channels 2 channels 3 channels
Supply voltage DC min: 10.8 Vdc .. max: 52,8 Vdc
Input current1) max 1,4A max 2,1A max 3,2A max 4,8A
Output voltage min: Vin/4 max: Vin-0,9V = Vin
Output current1) 350/500/700 mA/ch Max 1. A/ch 1)
max 1,4A max 2,1A max 3,2A max 4,8A
Nominal power 1) @12V 8,4/12/1 ,8 Wmax 12, /18/25,2 Wmax 38,4 Wmax 57, Wmax
@24V 1 ,8/24/33, Wmax 25,2/3 /50,4 Wmax 7 ,8 Wmax 115,2 Wmax
@48V 33, /48/ 7,2 Wmax 50,4/72/100,8 Wmax 153, Wmax 230,4 Wmax
Thermal shutdown 150 °C 150 °C
D-PWM dimming frequency 250Hz
D-PWM resolution 1 bit
D-PWM range 0,1 – 100 %
Storage Temperature min: -40 max: + 0 °C
Ambient Temperature 1) min: -10 max: +40 °C
Protection grade IP20
Wiring 2.5mm² solid - 1.5mm² stranded - 30/12 AWG
Mechanical dimensions 44 x 44 x 25 mm
Packaging dimensions 8 x 5 x 35 mm
Weight 40g
1) maximum value, dependent on the ventilation conditions
LED DRIVERS
DALC ET S.r.l.
Registered office: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Headquarters: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Tel. + 39 0444 183 80/18 7452 Fax. + 39 0444 18 7453
VAT: IT-04023100235
info@dalcnet.com www.dalcnet.com
DLC1248 multi channel
EASY RGB / EASY TW
Device Manual FW3.0+
Made in Italy
Rev. 201 -08-22
page 3/4
Installation
Connect the switching supply, connect the N.O. push button, connect leds.
DLC1248-2CC350 DLC1248-3CC350
DLC1248-2CC500 DLC1248-3CC500
DLC1248-2CC700 DLC1248-3CC700
DLC1248-2CV DLC1248-3CV
LED DRIVERS
DALC ET S.r.l.
Registered office: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Headquarters: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Tel. + 39 0444 183 80/18 7452 Fax. + 39 0444 18 7453
VAT: IT-04023100235
info@dalcnet.com www.dalcnet.com
DLC1248 multi channel
EASY RGB / EASY TW
Device Manual FW3.0+
Made in Italy
Rev. 201 -08-22
page 4/4
Function
The outputs status is memorized and reloaded in the case of supply interruptions.
TU ABLE WHITE
Tunable White is managed by a N.O. push button in the follo ing variants:
DLC1248-2CC350 DLC1248-2CC500 DLC1248-2CC700 DLC1248-2CV
Key Function
Click
Double Click
Long pressure (>1s) from OFF
Long pressure (>1s) from ON
ON/OFF
Maximum Intensity
Turn ON at 10% (night), then dimmer UP/DOWN
Color temperature UP/DOWN
RGB COLOUR
RGB colours are managed by a N.O. push button in the follo ing variants:
DLC1248-3CC350 DLC1248-3CC500 DLC1248-3CC700 DLC1248-3CV
Key Function
Click
Long pressure (>1s) from OFF
Long pressure (>1s) from ON
ON/OFF
Change rotation speed*
Start/stop color rotation
*Color rotation speed is selectable from 4 predefined levels.
The selected speed is visualized with a white strobo output:
- 10 flash/s for the rotation of seconds
- 5 flash/s for the rotation of 30 seconds
- 2 flash/s for the rotation of minutes
- 1 flash/s for the rotation of 30 minutes
Technical otes
Installation:
• Installation and maintenance must be performed only by qualified personnel in compliance with current regulations.
• The product must be installed inside an electrical panel protected against overvoltages.
• The product must be installed in a vertical or horizontal position with the cover / label upwards or vertically; Other positions are not permitted.
It is not permitted to bottom-up position (with the cover / label updown).
• Keep separated the circuits at 230V (LV) and the circuits not SELV from circuits to low voltage (SELV) and from any connection with this
product. It is absolutely forbidden to connect, for any reason whatsoever, directly or indirectly, the 230V mains voltage to the bus or to other
parts of the circuit.
Power Supply:
• For the power supply use only a SELV power supplies with limited current, short circuit protection and the power must be dimensioned
correctly.
In case of using power supply with ground terminals, all points of the protective earth (PE = Protection Earth) must be connected to a valid and
certified protection earth.
• The connection cables between the power source "low voltage" and the product must be dimensioned correctly and they should be isolated
from every wiring or parts at voltage not SELV. Use double insulated cables.
• Dimension the power supply for the load connected to the device. If the power supply is oversized compared with the maximum absorbed
current, insert a protection against over-current between the power supply and the device.
• For the constant current output, the voltage of LED module (Vf) must be less of 5V at the voltage of power supply.
Command:
• The length of the connection cables between the local commands (N.O. Push button or other) and the product must be less than 10m; the
cables must be dimensioned correctly and they should be isolated from every wiring or parts at voltage not SELV. Use double insulated
shielded and twisted cables.
• All the product and the control signal connect at the local command (N.O. Push Button or other) must be SELV (the devices connected must
be SELV or supply a SELV signal)
Outputs:
• The length of the connection cables between the product and the LED module must be less than 10m; the cables must be dimensioned
correctly and they should be isolated from every wiring or parts at voltage not SELV. Is preferable to use shielded and twisted cables.
LED DRIVERS
DALC ET S.r.l.
Registered office: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Headquarters: via Meucci, 35 - 3 040 Brendola (VI) - Italy
Tel. + 39 0444 183 80/18 7452 Fax. + 39 0444 18 7453
VAT: IT-04023100235
info@dalcnet.com www.dalcnet.com
Ce manuel convient aux modèles suivants
8
Autres manuels DALCNET Entraînement CC
Manuels Entraînement CC populaires d'autres marques
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces
Chamberlain Garog
Chamberlain Garog D Series Manuel utilisateur
Parker
Parker PDS Series Manuel utilisateur
Festo
Festo DGC G Series Guide de configuration
Binks
Binks QS-5012-1-CE Manuel utilisateur
