Dake TB-16 Manuel utilisateur

TB & SB Series Drill Presses

OWNERS MANUAL

BENCH AND FLOOR DRILL PRESS

TB-16 Series & SB-16-25-32-Series

FOR YOUR OWN SAFETYAND

OPTIMUM OPERATION READ

INSTRUCTION MANUAL BEFORE

OPERATING DRILL PRESS

RETAIN THIS MANUAL FOR

FURTHER REFERENCE

TABLE OF CONTENTS

•Model specifications page 2

•Electrical diagram page 2

•Voltage protection recommendations page 2

•Drill press installation page 3

•Safety points page 4

•Power warning page 5

•General safety instructions page 5-7

•Voltage warning and grounding instructions page 8

•Operation and set-up instructions page 10 –11

•Tooling removal page 12

•Work holding and machine maintenance page 12

•Speed adjustment and belt tensioning page 13

•Proper drill speeds for materials and bit diameter page 14

•Dake safety features page 14

•Exploded diagram TB / SB 16 page 15

•Parts list TB / SB 16 page 16

•Exploded diagram SB 25 / 32 page 17

•Parts list SB 25 / 32 page 18

MODEL AND SPECIFICATIONS

ELECTRICAL DIAGRAMS

CAUTION

20 AMP circuit breaker is recommended for the TB-16 and SB-16 models.

30 AMP circuit breaker is recommended for the SB-25 110 volt model.

Machine

Specifications:

Model TB-16

Model SB-16

Model SB-25

Model

SB-32

Drill Type Bench Floor Floor Floor

Max. Drill Capacity 5/8” 5/8” 1” 1-1/4”

Spindle Taper

MT2 MT2 MT3 MT4

Spindle Travel 3-1/8” 3-1/8” 5” 5-1/4”

Max. Work Diameter

14-1/8” 14-1/8” 18” 18”

Speeds (Step Pulley) 9 9 9 9

Spindle Speed Range 240-3400 240-3400 270-2000 270-2290

Column Diameter 3-1/8” 3-1/8” 3-5/8” 4”

Table

11-3/4 x 11-3/4” 11-3/4 x 11-3/4” 14 x 14” 15-3/4 x 15-3/4”

Base 17-3/4 x 12-1/8” 19-1/2 x 12-1/2” 23-1/2 x 15” 23-1/2 x 15”

Spindle to Table

16-1/2” 28-1/4” 28-1/4” 26-1/4”

Spindle to Base 25-1/2” 49” 49-1/8” 50”

Motor ½ HP ½ HP 1 HP 2 HP

Electrics CE CE CE CE

Voltage

120 Volt 120 Volt 220 V – 3 PH 220 V – 3 PH

Overall Height 42-1/2” 64” 71” 71”

Weight

155 lbs. 210 lbs. 397 lbs. 463 lbs.

1. UNCRATING AND INSTALLATION

CAUTION

INSTALLATION OF DRILL PRESS

MACHINE IS TOP HEAVY!

1. Location of the drill press should be in a well lit area with correct

power supply and that will not interfere with other machines or

operations.

2. Carefully uncrate machine from crate. Inspect all packing as not

to throw out any parts or manuals.

3. When transporting the machine please use caution. If using a

sling have someone steady the machine while transporting it.

4. Install your drill press on a sturdy level floor surface, or work

bench. (TB-16) The machine must be anchored to the floor or

workbench securely. Machine is top heavy.

5. Connect appropriate power to the machine. Make sure circuit

breakers are suitable for the machine. Consult local codes for

proper installation of machine. Always route power cables in a

safe manner away from traffic areas, damp areas, heat and

moving parts.

6. After installing the drill press, use the kerosene or degreasing

product to clean off the anti-rust oil which was applied at the

factory. Then wipe machined surfaces with a light coating of

lubricant oil. (Way oil)

7. Read rest of the owners manual before operating this machine.

Review and understand all safety instructions.

SAFETY POINTS

BEFORE USE, ALL SAFETY POINTS MUST BE READ AND UNDERSTOOD!

Before the DRILL PRESS is used,the instruction manual with this machine must be

read and understood. This manual offers safe operation instructions.

Offered below are safety instructions designed for the drill press and general

safety instructions that apply to most machinery.

Operation of the drill press incorrectly, or in a

dangerous fashion can result in serious injury

or death.

Operation of the drill press incorrectly, or in a

dangerous fashion can result in damage to

machine or it’s components and to the cutting

tool.

Instructions for safe drill press use.

Intend use:

The DRILL PRESS is designed to for drilling or boring operations. Caution is

required when operating the drill press because it can be dangerous due to

the high spindle rotation speed. Operation hazards such as entanglement,

shearing, ejection parts, etc. Guards such as pulley cover and chuck guard

must in place and working condition to prevent any hazard.

Please think about the safety warnings in the instruction manual before

operating the machine.

HIGH VOLTAGE

TURN OFF THE POWER

BEFORE SERVICE

2. FOR SAFE OPERATION

For your own safety read the instruction manual before operating

DRILL PRESS.

DANGER

3. GENERAL SAFETY INSTRUCTION

DANGER

GENERAL SAFETY

INSTRUCTION

1. SWITCH the POWER OFF before setting, inspecting

lubricating, cleaning or changing the drill bit.

2. Always wear the eye protection.

3. Do not wear gloves, necktie, necklaces, rings or loose

clothing.

4. To clamp work piece or brace against column to prevent

material rotation.

5. Use recommended speed for drill bit, and work piece

material.

1. Keep guards in place and in working order.

2. Remove adjusting key and wrenches. Be in the habit of

checking to see that keys and adjusting wrenches are

removed from tool before turning it on.

3. Keep work area clean. Cluttered areas and benches invite

accidents.

4. Do not use in dangerous environment. Do not use power

tools in damp or wet locations or expose them to rain. Keep

work area well lighted.

5. All visitors should be kept safe distance from work area.

6. Make workshop kid proof with padlocks, master switches, or

by removing starter key.

7. Do not force tool. It will do the job better and safer at the rate

for which it was not designed.

DANGER

GENERAL SAFETY

INSTRUCTION

Continued

8. Use the right tool. Do not force the tool, or use the machine to do a job for

which it was not designed.

9. Wear proper apparel. No loose clothing, gloves, necktie, rings or other jewelry

to get caught in moving parts. Non-slip footwear is recommended. Wear

protective hair covering to contain long hair.

10. Always use safety glasses. Also use face or dust mask if cutting operation is

dusty.

11. Secure work. Use clamps or a vise to hold work. Do not hold part with hands.

12. Do not overreach. Keep proper footing and balance at all times.

13. Maintain tools with care. Keep tools sharp and clean for best and safest

performance.

14. Disconnect drill press from power before servicing, when changing

accessories such as bits, cutter …etc.

15. Reduce the risk of unintentional staring. Make sure switch is in off position

before plugging in.

16. Use recommended accessories. Consult the owner’s manual for

recommended accessories. The use of improper accessories may cause risk

of injury to persons.

17. Never stand on machine, or serious injury could occur.

18. Check for damaged parts. Before further use of the machine, a guard or other

part that is damaged should be replaced or repaired. Carefully check to

determine that it will operate properly and perform its intended function. Check

for alignment of moving parts, binding of moving parts., breakage of parts or

mountings and any other conditions that affect its operation.

19. Never leave tool running unattended. Turn power off. Do not leave machine

until it comes to a complete stop.

4. SAFETY INSTRUCTIONS FOR DRILL PRESS

CAUTION

SAFETY INSTRUCTIONS

FOR DRILL PRESS

1. Wear eye protection.

2. Do not wear gloves, necktie, rings or loose clothing.

3. Clamp work piece or brace against column to prevent rotation.

4. Use recommended speed for drill bits and sizes and work piece materials.

5. Be sure drill bit or cutter tool is securely locked in the chuck.

6. Be sure chuck key is removed from the chuck before turning on power.

7. Adjust the table or depth stop to avoid drilling into the table, shut off the

power. Remove the drill bit or cutting tool, and clean the table before leaving

the machine.

8. Do not operate until it is completely assembled and installed according to the

instructions.

9. If any port of your drill press is malfunctioning or has been damaged or

broken, do not operate until the part is properly repaired or replaced.

10. Never place your fingers in a position where they could contact the drill or

other cutting tool if the work piece should unexpectedly shift.

11. Never use your hand to hold on the object while drilling, always clamp the

object tight on the working table.

12. Never perform any operation by moving the head or table with respect to one

another. Do not switch machine on or start any operation before checking

that the head and table lock handle are clamped tight to column, and head

and table support collars are correctly positioned.

13. Before switching the power on be sure the belt cover is down and the bit is

installed properly in the chuck.

14. Lockout the motor switch when leaving the drill press. Don’t perform layout,

assembly or setup work on the table while the cutting tools rotating.

5. VOLTAGE WARNING

WARNING

6. GROUNDING INSTRUCTION

VOLTAGE

WARNING

1. Before connecting the machine to a power source (receptacle, outlet…

etc.) Know your incoming voltage supply. (220, 208 etc.)

2. A power source with voltage greater than that specified for the machine

can result in serous injury to the user, and machine damage.

3. Using a power source with voltage less than that of the machines rating

can damage the motor and other components.

4. If you are unsure of the voltage rating do not use the machine.

CAUTION

GROUNDING

INSTRUCTION

1. In the event of a malfunction or breakdown, grounding provides a path of

least resistance for electric current to reduce the risk of electric shock.

This machine is equipped with an electric cord having an equipment

grounding conductor. The proper plug must be used with a matching

outlet that it is properly installed and grounded in accordance with all

local codes and ordinances.

2. For 120 volt models do not modify the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified electrician.

3. Improper connection of the equipment grounding can result in a risk of

electric shock. The conductor with insulation having an outer surface that

is green with yellow stripes is equipment grounding conductor. If repair or

replacement of the electric cord or plug is necessary, do not connect the

equipment grounding conductor to a live terminal.

4. Check with a qualified electrician or serviceman if the grounding

instructions are not completely understood, or if in doubt as whether the

machine is properly grounded.

5. It is not recommended to use an extension cord on this machine. If one

must be used, use only a grounded cord of proper size for machine and

length of run needed.

6. Repair or replace damaged or worn cords immediately.

7. OPERATION (PROCEDURE) Drill / Chuck Installation:

To show greater detail

chuck guard is in the open position in POWER MUST BE OFF BEFORE

photos. CHUCK GUARD MUST IN MAKING ANY ADJUSTMENTS!

PLACE DURING OPERATION! TURN POWER OFF! Before inserting

drill bits, chucks or arbors, always clean

out spindle hole and taper hole with a

clean cloth.

Open chuck jaws completely by turning

attached chuck key counter-clockwise

until the jaws are fully opened.

To install the chuck to the arbor tightly,

slide the chuck into the taper forcing it

into the spindle with by hand. Place a

block of wood on the table then lower the

spindle to make contact with the wood

and press the chuck tightly into the

spindles taper.

Install a taper shaft drill bit into the taper

the same way as you would the chuck. If

an adaptor is used it must fit the taper

correctly and the bit must fit snug in the

adaptor.

Table lock Table height adjustment:

Table height adjustment is

accomplished by loosening the clamp

bolt then adjusting the table with the

bracket handle to desired height.After

table is at working height, retighten

the clamp bolt securely.

Note: Keep table adjustment rack

clean from debris. Never attempt to

move table with clamp bolt tightened.

Table handle

Autres manuels pour TB-16

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Dake Outils électriques

Dake

Dake Force 50DA Manuel d'utilisation et d'entretien

Dake

Dake TB-16 Manuel d'utilisation et d'entretien

Dake

Dake 150H Manuel d'utilisation et d'entretien

Dake

Dake 75H Manuel d'utilisation et d'entretien

Dake

Dake ELEC-DRAULIC I PRESS 5-050 Manuel d'utilisation et d'entretien

Dake

Dake 25H Fiche technique

Dake

Dake FORCE 40 Manuel utilisateur

Dake

Dake TB-16V Manuel d'utilisation et d'entretien

Dake

Dake 25H Manuel d'utilisation et d'entretien

Dake

Dake SB-250V Manuel d'utilisation et d'entretien

Dake

Dake SB-25V Manuel utilisateur

Dake

Dake 50H Fiche technique

Dake

Dake Elec-Draulic I Fiche technique

Dake

Dake 3A Manuel d'utilisation et d'entretien

Dake

Dake 972210 Manuel utilisateur

Dake

Dake 4M Manuel d'utilisation et d'entretien

Dake

Dake SB-250V Manuel utilisateur

Dake

Dake FORCE 40 Manuel d'utilisation et d'entretien

Dake

Dake 33-578 Manuel d'utilisation et d'entretien

Dake

Dake 50H Manuel utilisateur

Dake

Dake 150H Manuel de la liste des pièces

Dake

Dake 8-025 Fiche technique

Manuels Outils électriques populaires d'autres marques

AEG

AEG OMNI-JS Manuel utilisateur

SIP

SIP 01533 Manuel utilisateur

Ribimex

Ribimex PRS499 Manuel utilisateur

3M Fiber Optic Connector Crimp Tool Manuel utilisateur

Ryobi

Ryobi P524 Manuel utilisateur

ROJEK

ROJEK FSN 300A Manuel utilisateur

Kemper

Kemper 1740PRO Manuel utilisateur

WABCO

WABCO OptiTire Manuel utilisateur

EINHELL

EINHELL TE-MS 18/210 Li Manuel utilisateur

Orgapack

Orgapack OR-T 85 Guide rapide

TOUGHCUT

TOUGHCUT Diamond 400 Manuel utilisateur

Yaros

Yaros PB-3603 Manuel utilisateur

Fein

Fein BSS 2.0 E Guide de configuration

Baileigh Industrial

Baileigh Industrial SS-2725 Manuel utilisateur

Milwaukee

Milwaukee 2674-20 Manuel utilisateur

Fein

Fein BLs 1.6 Manuel utilisateur

Princess

Princess Electric Multi Sharpener Manuel utilisateur

FOREDOM

FOREDOM K.1050 Manuel