Daewoo BM090 Manuel utilisateur
D1146 Primary filter:clean at every 5,000km,change at every 15,000km there
Change at every 20,000km. 166Page
Valve clearance Adjust at end of first 1,000km and every 20,000km there after. 171 Page
Air cleaner Clean at every 4,000km, change at every 12,000km there after. 176 Page
Transmission oil Change at end of first 5,000km and every 20,000km there after. 178 Page
Rear axle oil Change at end of first 5,000km and every 20,000km there after. 179 Page
Power steering oil Change at end of first 1,000km and every 24,000km there after. 180 Page
Power steering filter Change at end of first 1,000km and every 24,000km there after. 182 Page
IMPORTANT SERVICE ACTIVITIES
ҧAny failure resulting from a lack of normal maintenance as the maintenance service chart in this manual is not covered
by warranty.
CHECK ITEMS CHECK AND SERVICE INTERVALS PAGE
Engine oil 163 Page
Change : At end of first 1,000km,
long distance : every 30,000km
short distance : every 20,000km
D1146Ti
DE08TiS
DE12/T/Ti/TiS
Fuel filter
D1146
D1146Ti
DE12
DE12T
DE12Ti
Primary filter : clean at every 5,000km,
change at every 15,000km there after.
secondary filter : change at every 5,000km.
Engine oil filter Change with engine oil 164Page
DE08TiS
DE12TiS
Change : At end of first 1,000km,
High-speed, long distance : every 15,000km
In city, short distance : every 10,000km
This manual has been prepared to acquaint you with the operation and maintenance of your DAEWOO
BUSES and the provide important safety information. We urge you to read it carefully and follow the
recommendations to help assure the most enjoyable, safe and troublefree operation of your vehicle.
When it comes to service, remember that your DAEWOO dealer knows your vehicle best and is
interested in your complete satisfaction.
We would like to take this opportunity to thank you for choosing a DAEWOO product and assure
you of our continuing interest in your motoring pleasure and satisfaction.
This manual should be considered as a permanent part of your vehicle, and must remain with the
vehicle at the time of resale.
All information, illustrations and specifications contained in this manual are based on the latest product
information available at time of publication.
The right is reserved to make changes at any time without notice.
FOREWORD
1
1. IMPORTANT INFORMATIONŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 2
2. OPERATION AND CARE OF NEW VEHICLEŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 4
3. GETTING ON AND OFF, DRIVER’S SEAT AND BELT ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 6
4. INSTRUMENT, SWITCHES AND CONTROLSŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 14
5. DRIVINGŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 135
6. INSPECTION AND MAINTENANCEŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 162
7. LUBRICATION ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 213
8. SCHEDULED MAINTENANCE SERVICEŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 221
9. TROUBLESHOOTINGŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 225
10. MAIN DATA AND SPECIFICATIONŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 234
11. BODY DIMENSION ŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋŋ 253
TABLE OF CONTENTS
2
IMPORTANT INFORMATION
LOCATION OF ENGINE NUMBER AND CHASSIS NUMBER
It is advisable to keep note of the engine number and chassis number as they are required when contacting your deal-
er for repair services and parts order.
V.I.N plate
V.I.N(Vehicle identification Number)
plate is attached to the inner panel
above the front door.
Type A : Applicable for vehicles in
all countries except GCC
members.
V.I.N plate
V.I.N(Vehicle identification Number)
plate is attached to the inner panel
above the front door.
Type B : Applicable for vehicles in
GCC members.
Chassis number
The chassis number is stamped on
the upper face of the chassis frame
within the engine compartment.
3
Engine number Key
There are three types of key for the
bus ;
• Engine starting
• Mechanical locking for entrance
door (OPTION)
• Doors
– Entrance door operating
– Luggage doors (OPTION)
– Rear engine door (OPTION)
– Side engine doors (OPTION)
– Battery inspection door (OPTION)
–
Fuel tank inspection door (OPTION)
– Fuel inlet flap door (OPTION)
The keys are not interchangeable, but
door lock keys are interchangeable.
The code number of each key is
stamped on the key.
Record the key number and keep it
in a safe place.
In the event that the original key is
lost, duplicating can be done using
the key code information.
Engine No.
1378
4
OPERATION AND CARE OF NEW VEHICLE
It is important to observe the follow-
ing precautions as operation and care
of the vehicle, particularly during the
break–in period have a strong influ-
ence over the performance and ser-
vice life of the vehicle.
1. Start and let the engine idle until
it becomes thoroughly warmed up
and coolant temperature increases
beyond 50°C (or 125°F) before
starting off.
2. Avoid racing the engine, abrupt
starts and hard stops.
3. Avoid over loading the vehicle dur-
ing and after the break–in period.
Over loading
Over loading not only shortens the
service life of your vehicle but also
create serious potential safety haz-
ards.
The weight of payload must be limit-
ed within the GVW rating and distrib-
uted over the front and rear axles so
as not to exceed the axle capacities.
Refer to “MAIN DATA AND SPECIFI-
CATION” for GVW and Axle capaci-
ty.
Maintenance
In order to maintain safe and depend-
able vehicle operation, inspection and
adjustment should be performed as
outlined in “INSPECTION AND MAIN-
TENANCE”.
Your DAEWOO dealer is willing to
perform regular maintenance opera-
tion on your vehicle.
5
Engine oil change
Change engine oil filter catridge to new one at the
same time with engine oil.
Maximum engine speed
During the initial milage(Break–in period : 2,000km),
confine engine speed to 70% of the maximum and
scan the tachometer as you drive to prevent engine
over–running.
After the break–in period, increase the engine speed
gradually to complete running–in of the vital parts.
Engine Model Change Interval
D1146 At end of first 1,000km
D1146Ti High–speed, long distance :
DE12Ti every 15,000km
DE12TiIn city, short distance :
DE12Ti every 10,000km
DE08TiS At end of first 1,000Km
Long distance : every 30,000km
DE12TiS short distance : every 20,000km
6
GETTING ON AND OFF, DRIVER’S SEAT AND BELT
DOOR OPENING AND CLOSING
(Applicable for vehicles in all
entrance door with mechanical key)
When opening the front door to get
in, first unlock the mechanical key on
the entrance door and operate the
entrance key on the right side of the
front middle panel.
When closing the front door to get
off, open the front door by operating
the door control switch and get off.
In the outside of bus, close the door
with the key and look the mechanical
key on the entrance door not to be
opened in case of air leaking.
(Applicable for vehicles in all
entrance door except mechanical key)
When opening the front door to get
in, operate the entrance key on the
right side of the froot middle panel.
When closing the front door to get
off, open the front door by operating
the door control switch and get off.
In the outside of bus, close the door
with the key.
I
D
L
I
N
G
H
.
.
L
Before operating entrance key, unlock
mechanical key on door frame.
NOTICE
When opening front entrance door for a long time, setting emergency valve
at manual position and put control switch in close position. When returning
to automatic condition, putting control switch and door in same condition
and set emergency valve at automatic position.
CAUTION
(Type A : Toggle switch) (Type B : One touch switch)
7
MANUAL OPENING AND
CLOSING
Type A : Select type
As setting the “Auto–Manual” change
lever installed right, lower inner side
of front panel(beside of driver’s right
leg), the door can be opened and
closed by hands.
Type B :
Push/Pull or rotary type (OPTION)
As setting the "Auto-Manual" change
knobs are installed two types. One of
the types installed inner upper panel
the entrance door operated by air.
Other installed outer mid panel on left
side of door operated by electric push
button. the door can be opened and
closed by hands.
I
D
L
I
N
G
H
.
.
L
(Push/Pull type) (Rotary type)
8
Adjustment of Fixed type (S-104H) (BM090, BS090)
1. Back angle adjustment
To adjust the seat back, turn No. 1 handle, and lean
backwards and foreward until desired angle is
achieved.
2. Slide adjustment
To move the seat forward and backward.
Pull No. 2 lever, forward and slide the seat.
3. Height (Tilting) adjustment
Desired the seal height can be achieved by puling
No. 3 lever upward and downward.
2
1
2
3
1
DRIVER’S SEAT AND BELT
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Daewoo Autre
