Da-Lite Da-Snap 74610 Manuel utilisateur

POWER

PRESENTATION PRODUCTS

The

Instruction Book For

Da-Snap Screen

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574/267-8101

800-622-3737

Fax: 574/267-7804

http:// www.da-lite.com

e-mail: [email protected]

WALL BRACKET

Quantities vary by screen size

Screens smaller than 80" viewing width = 1

Screens 80" to 96" viewing width = 2 QUANTITY INCLUDED __________

Screens over 96" viewing width = 3

Installation screws not included

LOWER WALL BRACKET

Quantity of 1. Only for screens

smaller than 80" viewing width QUANTITY INCLUDED __________

Installation screws not included

SNAP STUD

QUANTITY INCLUDED ________

#10 SCREW

QUANTITY INCLUDED ________

FRAME BRACKET

Quantities vary by screen size

Screens smaller than 80" viewing width = 3

Screens 80" to 96" viewing width = 4

Screens over 96" viewing width = 6

QUANTITY INCLUDED ________________________________

HIGH POWER FRAME BRACKET

Screens with High Power viewing surface quantity = 1

Screens with 2-piece side frame rails quantity = 2

QUANTITY INCLUDED ________________________________

1. Unpack the frame parts from the carton. DO NOT

unroll the screen surface at this time.

2. Take care to observe the color code on the parts.

Assemble the top and bottom frame members on the

left and right sides using the #10 black screws and

snap studs. See figure 1.

FRAME ASSEMBLY

FIGURE 1. REAR VIEW

SNAP STUD

SIDE

#10 BLACK SCREW

SIDE

TOP

BOTTOM

SNAP STUD

There are four methods of installation based on the size

of the screen and type of viewing surface. Measure the

width of the viewing area of your screen and refer to the

appropriate method of installation below. The hanger

bracket diagram shows the type and quantity of bracket

that is supplied based on the size of the screen.

Method 1: Screens smaller than 80" in viewing width.

Method 2: Screens 80" to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power viewing

surface.

Method 1

1. Use the supplied #10 screws to attach three frame

brackets to the back of the frame as shown in figure

INSTALLATION

2. Secure the wall bracket to wall studs at the desired

height. Make sure the bracket is level. The top of the

frame will be 1/8" above the top of the wall bracket

when mounted. You will need at least 5/8" clearance

above the bracket to hang the screen.

3. To install the lower wall bracket, you must measure

the overall height of the screen frame and subtract

1-3/8". Using that dimension, measure down from the

top edge of the wall bracket and mark the wall for

two screw holes. The holes should be centered

within the frame and 6" apart. Refer to figure 3.

4. Attach the lower wall bracket to the wall. Refer to

figure 4 for proper orientation. Do not tighten the

screws completely. The bracket should slide up and

down easily.

5. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the inside of

the roll. Place the frame over the screen surface, and

while lifting the frame with one hand, snap the

screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

6. Hang the screen on the brackets by hooking the

bottom of the frame onto the lower wall bracket and

lift up until you can hook the top of the frame on the

top bracket. Push down on the frame to seat it on the

brackets. Refer to figure 4.

FIGURE 2

FRAME BRACKETS

3-PIECES

#10 SCREWS

6-PIECES

WALL BRACKET

1-PIECE

LOWER WALL BRACKET

1-PIECE

FIGURE 3

OVERALL HEIGHT - 1-3/8"

OVERALL

HEIGHT

FIGURE 4

LIFT

WALL

Method 2

1. Use the supplied #10 screws to attach four frame

brackets to the back of the frame as shown in

figure 5.

2. Secure the wall bracket to wall studs at the

desired height. Make sure the bracket is level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen.

3. To install the lower wall bracket, you must

measure the overall height of the screen frame

and subtract 1/4". This is the dimension from the

top of the upper wall bracket to the bottom of the

lower wall bracket. See figure 6.

4. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

5. Position the screen with the attached surface

onto the top wall bracket as shown in figure 7.

Push down at the center of the bottom frame rail

to hook onto the lower wall bracket.

Method 3

1. Use the supplied #10 screws to attach six frame

brackets to the back of the frame as shown in

figure 8.

2. Secure the wall brackets to wall studs at the

desired height. Make sure the brackets are level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen.

3. To install the lower wall bracket, you must

measure the overall height of the screen frame

and subtract 1/4". This is the dimension from the

top of the upper wall bracket to the bottom of the

lower wall bracket. See figure 6.

4. Some large screen sizes are made with 2-piece

side frame rails. For this type of frame you will

need to attach one High Power bracket to each

side at the joint. See figure 8.

FIGURE 5

FRAME BRACKETS

4-PIECES

#10 SCREWS

8-PIECES

WALL BRACKET

2-PIECES

FIGURE 6

OVERALL HEIGHT -1/4"

OVERALL HEIGHT

WALL

INSTALLATION

WALL

FIGURE 7

FIGURE 8

FRAME BRACKETS

6-PIECES

#10 SCREWS

12-PIECES

WALL BRACKETS

3-PIECES

HIGH

POWER

BRACKET

FOR

LARGE

SPLIT

FRAMES

ONLY.

2-PIECES

INSTALLATION

5. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

6. Position the screen with the attached surface

onto the top wall bracket as shown in figure 7.

Push down at the center of the bottom frame rail

to hook onto the lower wall bracket.

7. If you attached brackets to the side frame rails in

step 4, anchor these to the wall with an

appropriate fastener for your type of wall.

Method 4

1. Use the supplied #10 screws to attach two frame

brackets and two High Power brackets to the

back of the frame as shown in figure 9.

2. Secure the wall bracket to wall studs at the

desired height. Make sure the bracket is level.

The top of the frame will be 1/8" above the top of

the wall bracket when mounted. You will need at

least 5/8" clearance above the bracket to hang the

screen.

3. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the

inside of the roll. Place the frame over the screen

surface, and while lifting the frame with one

hand, snap the screen surface onto the frame

with the other hand while maintaining a steady

pull on the surface.

4. Position the screen with the attached surface

onto the top wall bracket as shown in figure 7.

Push down at the center of the bottom frame rail

to tension the fabric. Mark the screw holes for

the bottom brackets. Drill holes in wall and attach

the brackets to the wall with screws.

CLEANING

Da-Tex, Dual Vision, Pearlescent, Cinema Vision, High

Power, Da-Mat, High Contrast Da-Mat, Audio Vision, High

Contrast Audio Vision, High Contrast Cinema Vision and

High Contrast Cinema Perf surfaces can be cleaned as

follows:

Using a white clean cloth (100% cotton preferred)

that is dampened with clear water, gently wipe the

area in one direction. Do not use a circular motion.

Using a dry 100% cotton cloth, wipe dry after each

cleaning session. To clean a stubborn stain or a

sticky surface, use denatured alcohol (methanol or

methyl alcohol) following the same procedure as for

water. For extremely stubborn stains, use V M & P,

Naphtha or Super Naphtha and follow the same

procedure as for water.

FIGURE 9

FRAME BRACKETS

2-PIECES

#10 SCREWS

8-PIECES

WALL BRACKET

1-PIECE

HIGH POWER BRACKET

2-PIECES

Printed in U.S.A. 75135 Rev. 1/03

Table des matières

Autres manuels Da-Lite Écran de projection

Da-Lite

Da-Lite IDEA Thin Manuel utilisateur

Da-Lite

Da-Lite Tensioned Conference Electrol Manuel utilisateur

Da-Lite

Da-Lite ASCENDER ELECTROL Manuel utilisateur

Da-Lite

Da-Lite ADVANTAGE ELECTROL Instructions de montage

Da-Lite

Da-Lite TENSIONED LARGE COSMOPOLITAN ELECTROL Manuel utilisateur

Da-Lite

Da-Lite TENSIONED LARGE ADVANTAGE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Large Dual Masking Electrol Manuel utilisateur

Da-Lite

Da-Lite ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Da-Snap Screen Manuel utilisateur

Da-Lite

Da-Lite Cosmopolitan Electrol Manuel utilisateur

Da-Lite

Da-Lite Deluxe Insta-Theater Manuel utilisateur

Da-Lite

Da-Lite LARGE ADVANTAGE DELUXE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite TENSIONED EXECUTIVE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Presenter P-50 Manuel utilisateur

Da-Lite

Da-Lite Deluxe Insta-theater Manuel utilisateur

Da-Lite

Da-Lite TILT-LOCK Manuel

Da-Lite

Da-Lite Designer Da-Tab Electrol Manuel utilisateur

Da-Lite

Da-Lite TENSIONED CONTOUR ELECTROL Manuel utilisateur

Da-Lite

Da-Lite Advantage Manuel utilisateur

Da-Lite

Da-Lite DesIgner Contour Manual Manuel utilisateur

Da-Lite

Da-Lite PROFESSIONAL ELECTROL Manuel utilisateur

Da-Lite

Da-Lite ADVANTAGE ELECTROL Manuel utilisateur

Da-Lite

Da-Lite TENSIONED PROFESSIONAL ELECTROL Manuel utilisateur

Da-Lite

Da-Lite ADVANTAGE ELECTROL Manuel utilisateur

Manuels Écran de projection populaires d'autres marques

FART PRODUKT

FART PRODUKT Standard SCREEN Manuel utilisateur

Draper

Draper E Series Manuel

Elite Screens

Elite Screens Elite Tripod Series Manuel utilisateur

Laarhoven

Laarhoven Companion II Manuel utilisateur

Renogy

Renogy RMS-LFPS-US Manuel utilisateur

Samsung

Samsung S*H65* Manuel utilisateur

FONESTAR

FONESTAR PPTR-43100-FA Manuel utilisateur

Slide Clear

Slide Clear Varro XL Manuel utilisateur

Elite Screens

Elite Screens M85XWS1-SRM Manuel utilisateur

OS РХ-090Н Manuel utilisateur

Niko

Niko 10-845 Manuel utilisateur

Speaka Professional

Speaka Professional 2357532 Manuel d'utilisation

Sima

Sima XL-72 Manuel utilisateur

Jasic

Jasic EVO 2.0 ET-200P Manuel utilisateur

Elite Screens

Elite Screens Starling 2 Series Manuel utilisateur

InFocus

InFocus SC-WALL GRY-92H Manuel

Barco

Barco OverView MVL-615 Manuel utilisateur

Draper

Draper Envoy Manuel