D-Link DAP-2230 Feuille d'instructions

Autres manuels pour DAP-2230

3

Ce manuel convient aux modèles suivants

7

Table des matières

Autres manuels D-Link Point d'accès sans fil

D-Link

D-Link Nuclias Cloud DBA-X1230P Manuel utilisateur

D-Link

D-Link Air Premier DAP-2695 Manuel utilisateur

D-Link

D-Link DWL-6620APS Manuel utilisateur

D-Link

D-Link DAP-2660 Manuel utilisateur

D-Link

D-Link AirPremier N DAP-2690 Manuel utilisateur

D-Link

D-Link DAP-1150 Manuel utilisateur

D-Link

D-Link nuclias connect DAP-2662 Manuel utilisateur

D-Link

D-Link DAP-1665 Manuel utilisateur

D-Link

D-Link DWL-3200AP - AirPremier - Wireless Access... Manuel utilisateur

D-Link

D-Link DAP-1513 Manuel utilisateur

D-Link

D-Link DWL-6720AP Manuel utilisateur

D-Link

D-Link DAP-2230 Manuel utilisateur

D-Link

D-Link DWL-1000AP Manuel utilisateur

D-Link

D-Link DWL-2700AP - AirPremier Outdoor Wireless Access... Manuel utilisateur

D-Link

D-Link DAP-3410 Manuel utilisateur

D-Link

D-Link UNIFIED WIRED & WIRELESS ACCESS SYSTEM... Manuel utilisateur

D-Link

D-Link AirPremier DWL-2210AP Manuel utilisateur

D-Link

D-Link DWL-3200AP - AirPremier - Wireless Access... Manuel utilisateur

D-Link

D-Link DAP-1360L Manuel utilisateur

D-Link

D-Link D DWL-8200AP DWL-8200AP Manuel utilisateur

D-Link

D-Link AirPlus Xtreme G DWL-2000AP Manuel utilisateur

D-Link

D-Link DAP-1150 Manuel utilisateur

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

D-Link

D-Link DAP-1155 Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur

Draytek

Draytek VIGORAP 902 Manuel utilisateur

EnGenius

EnGenius EAP350 Manuel utilisateur

- 1 -

Manual to install the firmware

For DAP-2230 Rev.A, DAP-2310 Rev.B, DAP-2360 Rev.B, DAP-2610 Rev.A,

DAP-2660 Rev.A, DAP-2680 Rev.A, DAP-2695 Rev.A and DAP-3662 Rev.A

Important:

After the firmware upgrade the DAP can’t be used in a Central Wi-Fi Manager (CWM)

System or in an AP-Array System.

You would need to install the „not-NC-firmware“ into your DAP again.

See the attached manual

“Manual for Downgrade from Nuclias Connect Firmware.pdf”

Recommendation:

Connect the DAP and the PC, with it you make the firmware upgrade, with a LAN cable

with your network, there is also the DHCP server available.

For the installation of the firmware please follow this.

1. Get access to the setup of your DAP via web browser.

The default address is http://192.168.0.50 or when you already implemented the DAP

into your network please call the IP-address this you configured into you DAP or this the

DAP got from the DHCP server in you network.

2. By default the setup has no password.

At User name enter admin and then click onto Login.

Note:

Did you set an Admin-Password please enter this.

Do you don’t know the Admin-Password anymore you must reset the DAP to factory

defaults (Factory Reset).

For this press the Reset button of the running DAP for example with a paperclip or pencil

for 5-10 seconds.

- 2 -

3. At the top choose the menu Maintenance and then in the open menu

Firmware and SSL Certification Upload.

4. At Upload Firmware From File click onto Choose File.

Pick the previously un-zipped firmware file

DAP-2610_RevA_Firmware_200r063.bin

and click onto Upload.

5. The firmware will be installed now.

This takes close to 5 minutes.

6. Important:

You must reset the DAP to factory defaults (Factory Reset).

For this press the Reset button of the running DAP for example with a paperclip or pencil

for 5-10 seconds.

After the DAP is restarted it is ready to integrate into a Nuclias Connect environment.

- 3 -

If your DAP is build-in and you cant’t press the Reset button easily you

can reset it over the setup instead.

7. Log-in into the setup again.

At User name enter admin and then click onto Login.

Did you set an Admin-Password please enter it.

8. At System Country choose any country and click onto Update.

- 4 -

9. Please wait 2 minutes.

10. Log-in into the setup again.

At User name enter admin.

At Password please enter also admin.

From now this is the default Admin password until you configure the DAP new.

Click onto Login.

11. At the top choose the menu System.

Click onto Restore.

- 5 -

12. Click onto OK.

13. Please wait two minutes.

After the DAP is restarted it is ready to integrate into a Nuclias Connect environment.

To check the detailed version number of the installed version please log-in into the setup

of your DAP.

In the address line of your web browser enter

http://<ip-adresse>/version.txt

The <ip-adresse> is for the IP-address of your DAP.

A page with detailed information about the firmware appears.