D-Link DGS-3420-28TC Manuel utilisateur
Quick Installation Guide
Краткое руководство по установке
xStack L3 Managed Stackable Gigabit Switch with
20 ports 10/100/1000Base-T 4 Combo 10/100/1000Base-T/SFP ports and
4 ports SFP+ /
Управляемый L3 стекируемый коммутатор с
20 портами 10/100/1000Base-T 4 комбо-портами 100/1000Base-T/SFP и
4 портами 10GBase-X SFP+
DGS 3420 28TC
Introduction
This Quick Installation Guide gives instructions for setting up the D-Link DGS-3420-2 TC switch. The model
you have purchased may appear slightly different from those shown in the illustrations. For more detailed
information about the device, its components, making network connections and technical specifications,
please refer to the D-Link website http://www.dlink.com/.
Package Contents
• DGS-3420-2 TC Switch
• Power Cord
• Two rack mounting brackets
• RJ-45 to RS-232 console cable
• 4 Rubber Feet
• Mounting kit
• Quick Installation Quide
If any of the above items are damaged or missing, please contact your local reseller for replacement.
2
Hardware Overview
LED Indicators
3
LED Indicative Colour Status Description
Power Green Solid Green Power on.
Light off Power off.
RPS Green Solid Green Redundant Power Supply is in use.
Light off RPS is not in use.
Blinking Green RPS is connected.
SD Green / Red Solid Green If a Secure Digital (SD) card is plugged in.
Blinking Green The Switch is reading or writing data to and from the SD card.
Light off No SD card is plugged into the SD port.
An SD card failure has been detected.
Link/Act Green /
Orange
Solid Green
Solid Orange When there is a secure connection to a 10/100Mbps Ethernet device at any
of the ports.
Blinking Green When a 1000Mbps port is active.
Blinking Orange When a 10/100Mbps port is active.
No link or activity.Light off
Console Green Blinking Green
Solid Green When a user is logged in through the console port.
Solid Red
When there is a secure connection to a 1000Mbps Ethernet device at any
of the ports.
Light off When the POST is finished.
During the Power-On Self Test (POST).
1 – 12
H The device was assigned as the stacking Master.
The device was selected to be the Backup Master.
The Safeguard Engine feature enters the exhausted mode.
h
G
Stack ID The box ID is assigned either by the user (static mode) or by the system
(automatic mode). For standalone Switches, this will display number “1”.
MGM Green Solid Green
Blinking Green Secure connection established.
Light off Console off.
Console on.
Installation
Desktop or Shelf Installation
When installing the switch on a desktop or shelf, the rubber feet included with the device must be attached on
the bottom at each corner of the device’s base. Allow enough ventilation space between the device and the
objects around it.
Rack Installation
The Switch can be mounted in a standard 19"(1U) rack using the provided mounting brackets. Fasten the
mounting brackets to the sides of the Switch using the screws provided.
4
Fasten the mounting brackets in any available open space in the rack using the screws provided.
Installing Transceivers into the Transceiver Ports
The Switch is equipped with Small Form-factor Pluggable plus (SFP+) ports, which supply connecting SFP,
WDM SFP and SFP+ transceivers.
5
Connecting to Power
Power On (AC Power)
Plug one end of the AC power cord into the power connector of the Switch and the other end into the local
power source outlet..
Power Failure (AC Power)
In the event of a power failure, just as a precaution, unplug the Switch. After the power returns, plug the
switch back in to the power socket.
Connecting to a Redundant Power Supply
The DPS-500 connects to the Switch using a 14-pin DC power cable. A standard, three-pronged AC
power cable connects the redundant power supply to the main power source.
6
1. Insert one end of the 14-pin DC power cable into the port on the switch and the other end into the
redundant power supply.
2. Using a standard AC power cable, connect the redundant power supply to the main AC power source. A
green
LED on the front of the DPS-500 will glow to indicate a successful connection.
3. Re-connect the switch to the AC power source. The LED indicator will show that a redundant power
supply is now in operation.
4. Do not make any changes on the switch.
7
Switch Connections
Switch to End Node
End node is a generic name for edge networking devices that will be connected to this switch. Typical
examples of end nodes are Personal Computers (PCs), Notebooks, Access Points, Print Servers, VoIP
Phones and more. An end node connects to the Switch via a twisted-pair UTP/STP cable. Connect the end
node to any of the 1000Base-T ports of the Switch. The Link/Act LEDs for each Ethernet port turns green or
orange when the link is active. A blinking LED indicates packet activity on that port.
NO E: all high-performance N-Way Ethernet ports can support both MDI-II and MDI-X connections.
Switch to Switch
There is a great deal of flexibility on how connections are made using the appropriate cabling.
• Connect a 10Base-T switch port to the Switch via a twisted-pair Category 3, 4 or 5 UTP/STP cable.
• Connect a 100Base-TX switch port to the Switch via a twisted-pair Category 5 UTP/STP cable.
• Connect 1000Base-T switch port to the Switch via a twisted pair Category 5e UTP/STP cable.
• Connect switch supporting a fiber-optic uplink to the Switch’s SFP ports via fiber-optic cabling.
Connect to a Network Backbone or Server
The 1000Base-T SFP ports are ideal for uplinking to a network backbone, server or server farm.
Management Options
Web-based Management Interface
After successfully installing the Switch, the user can configure the Switch, monitor the LED panel, and
display statistics graphically using one of the Web browsers given below:
• Internet Explorer (version 5.5 and later)
• Netscape (version and later)
• Mozilla Firefox (version 2.0 and later)
• Google Chrome (version 6.0 and later)
• Safari (version 4.0 and later)
SNMP-based Management
The Switch can be managed with an SNMP-compatible console program. The Switch supports SNMP
version 1.0, version 2.0 and version 3.0.
Command Line Interface
The user can also connect a computer to the serial console port to access the Switch. The command line
interface provides complete access to all Switch management features.
Connecting the Console Port
To use the RJ-45 console port, the following equipment is needed:
• A terminal or a computer with both an RS-232 serial port and the ability to emulate a terminal (it is possible
to use Hyperterminal, Putty, Minicom etc).
• A console cable with a male DB-9 connector on one end and an RJ-45 connection on the other. This cable
should be included with the Switch.
To connect a terminal to the console port:
1. Connect the male DB-9 connector on the console cable to the RS-232 serial port on the computer.
2. Insert the RJ-45 connector into the console port on the front of the Switch. Set the terminal emulation
software as follows:
• Serial port: COM port 1 or COM port 2
• Baud rate: 115200
• Data bits:
• Parity: none
• Stop bits: 1
• Flow control: none
• Under Properties, select VT100 for Emulation mode.
• Select Terminal keys for Function, Arrow and Ctrl keys. Make sure to use Terminal keys (not Windows keys)
are selected.
T
3. After you have correctly set up the terminal, plug the power cord into the power receptacle on the back of
the Switch. The boot sequence appears in the terminal. After the boot sequence completes, the console login
screen displays.
First ime Connecting to the Switch
Upon initial connection to the Switch, the login screen appears (see example below).
Press Enter in both the Username and Password fields. Then access will be given to enter commands after
the command prompt DGS-3420-28 C:admin#
There is no initial username or password. Leave the Username and Password fields blank.
NO E: the first user automatically gets Administrator level privileges. At least one Admin-level user account
must be created for the Switch.
9
10
Connecting to the Management Port
The front panel of the Switch features a Management portwhich can be used to connect to a computer
using a standard Ethernet cable. A web browser or Telnet client can be used to connect to the Switch
using the MGMT port.
The default IP address of the Management port is 192.16 .0.1, and a subnet mask of 255.255.255.0.
Make sure that the computer being used for Switch management has a nonconflicting IP address in the
192.16 .0.x subnet.
The IP settings or enabled status of the Management port can be changed through the console port. To
change the configuration of the Management port, use the command:
config out_band_ipif {ipaddress <network_address> | state [enable | disable] | gateway <ipaddr>}
To view the status or IP settings, use the command:
show out_band_ipif
To change settings for the out-of-band Management port in the web interface, use the following path:
Management > Out of Band Management Settings
Logging onto the Web Manager
To access the Web User Interface the user simply runs the standard web browser and enter the Switch’s IP
address into the address bar of the browser and press the Enter key. To access the Web UI from normal
LAN ports, the user needs to configure an IP address for this interface first before it can be accessed via the
Web User Interface:
The PC must have an IP address in the same subnet as the switch. For example, if the switch has an IP
address of 10.90.90.90, the PC should have an IP-address of 10.x.y.z (where x/y is a number between
0 ~ 254 and z is a number between 1 ~ 254), and a subnet mask of 255.0.0.0. Open the web browser and
enter 10.90.90.90 (the factory-default IP address) in the address bar. Then press Enter.
Additional Information
For more detailed information on how to set up and configure the DGS-3420-2 TC, please refer to the
D-Link Website http://www.dlink.com/.
Table des matières
Langues :
Autres manuels D-Link Changer
D-Link
D-Link DES-3326S - Switch - Stackable Manuel utilisateur
D-Link
D-Link DGS-1210-28/ME Manuel utilisateur
D-Link
D-Link DFE-916x Manuel utilisateur
D-Link
D-Link Web Smart DES-1210-28 Manuel utilisateur
D-Link
D-Link DES-1228 - Web Smart Switch Manuel utilisateur
D-Link
D-Link xStack DGS-3600 Series Manuel utilisateur
D-Link
D-Link DCH-G020 Manuel utilisateur
D-Link
D-Link DKVM-2U Manuel utilisateur
D-Link
D-Link DES-108 Manuel utilisateur
D-Link
D-Link xStack DES-6500 Manuel utilisateur
D-Link
D-Link DES-3028 Manuel utilisateur
D-Link
D-Link DMS-107 Manuel utilisateur
D-Link
D-Link DGS-1005D - Switch Manuel utilisateur
D-Link
D-Link DGS-1210-52MP Manuel utilisateur
D-Link
D-Link xStack DGS-3620-52P Manuel utilisateur
D-Link
D-Link DUB-1340 Manuel utilisateur
D-Link
D-Link EasySmart DGS-1100-08 Manuel utilisateur
D-Link
D-Link xStack DGS-3427 Manuel utilisateur
D-Link
D-Link DGS-1224TP - Web Smart Switch Manuel utilisateur
D-Link
D-Link xStack DGS-3612G series Manuel utilisateur
Manuels Changer populaires d'autres marques
Ruijie
Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation
Altinex
Altinex DA1914SX Manuel utilisateur
MiLAN
MiLAN MIL-SM2401M Manuel utilisateur
RJM
RJM MASTERMIND PBC/6X Manuel utilisateur
Atlas
Atlas MMK-KVM8 Manuel utilisateur
Cabletron Systems
Cabletron Systems GIGAswitch GSR-16 Manuel utilisateur