D-Link Air DCS-1000W Manuel utilisateur

1

Setting Up DCS-1000W Camera & Internet

Gateway Router

2

Once logged into the camera, on the main

menu, click/select System. Enter a Camera

Name and Location. You will also be able to

assign a Admin Name and Password.

Configure the Camera with QIG.

3

There are two ways to assign an IP address. To configure

the DCS-1000W for security purposes, it will be necessary

to manually assign an IP address for use behind an

Internet Router. The Default Gateway will be the IP

Address of the Internet Router’s LAN IP Address.

IP Assignment

4

In the “Wireless Interface” section, you will be asked for your “Connection

Mode,” “Network Name” and “Encryption WEP Key.” Choose either HEX or

ASCII. Your “Wireless Channel” should also be set.

This information should be written down and saved for configuration of the

Wireless Router and other Wireless Cameras.

Settin

g

up your Wireless Connection

and Encryption

5

Opening Outside Ports will allow users to view the Camera

Images from inside or outside the Wireless Network. The Web

Server Port is a proprietary port used in the IP address from a

remote location. (Ex. http://10.80.1.250:83)

The ports that are opened must be unique for each camera,

to successfully view the images from an outside network.

Assigning and Opening outside ports.

6

These fields control Input Trigger 1 and Trigger

2. Each Input trigger can trigger either or both

Output triggers.

SMTP Server Address: Name or IP address of a

SMTP Mail Server that the camera can send images to.

Sender E-Mail: Name of the Camera/Trigger that

sent the mail

Receiver E-Mail: Account Name of person to receive

pictures when sensors are activated

Sending Interval: The time between additional

sequences of pictures are taken when sensors

activated

Sending Times: The number of times the camera

takes additional sequences of pictures based on

Sending Interval.

Trigger I/O: Enable Output trigger for the specified

input trigger

Output # Time: How long the output trigger is

activated if Sensor is activated. (i.e.. How long should

siren ring?)

I/O Input Trigger 2

Security Notification Configuration

I/O Input Trigger 1

7

Configure all Cameras that will be used in The

Wireless Security Network

8

Configure the initial settings by following the steps outlined in the

DI-614+ QIG. Once logged into the Router, on the main menu,

click/select “Wireless.”

Router Set-Up and Installation

9

In the “Wireless Interface”

section, you will be asked for

your SSID (“Network Name”)

and “Encryption WEP Key.”

Choose either HEX or ASCII.

Your “Wireless Channel” should

also be set.

This information should be

entered from the notes taken

on the configuration of the

Wireless Camera.

Currently, D-Link only produces

Cameras based on 802.11b.

Therefore, 128 bit encryption is

the maximum that can be used.

Settin

g

up your Wireless Connection

and Encryption

10

There are two ways to assign an IP address. To configure the

DI-614+ for security purposes, it will be necessary to

manually assign an IP address for use with the Internet

Router.

WAN IP Assignment

Autres manuels pour Air DCS-1000W

4

Table des matières

Autres manuels D-Link Routeur réseau

D-Link

D-Link DES-1048G Manuel utilisateur

D-Link

D-Link DIR-2640 Manuel utilisateur

D-Link

D-Link DWR-921 Guide de configuration

D-Link

D-Link Amplifi DIR-645 Manuel utilisateur

D-Link

D-Link DES-3010F Manuel utilisateur

D-Link

D-Link DWR-922 Manuel utilisateur

D-Link

D-Link DSL-2640B Manuel utilisateur

D-Link

D-Link DIR-600L Manuel utilisateur

D-Link

D-Link myPocket DIR-457 Manuel utilisateur

D-Link

D-Link xStack DES-3200 Series Manuel utilisateur

D-Link

D-Link DSL-500 Manuel utilisateur

D-Link

D-Link DES-3528 - xStack Switch - Stackable Manuel utilisateur

D-Link

D-Link DWR-922 Manuel utilisateur

D-Link

D-Link DES-1005 Manuel utilisateur

D-Link

D-Link DSL-4320L Manuel utilisateur

D-Link

D-Link DIR-895L Manuel utilisateur

D-Link

D-Link DSL-2750U Fiche d'information produit

D-Link

D-Link DSL-2730U Manuel utilisateur

D-Link

D-Link GO-DSL-N151 Manuel utilisateur

D-Link

D-Link DKT-810 Manuel utilisateur

D-Link

D-Link DIR-875 Manuel utilisateur

D-Link

D-Link DSL-504 Manuel utilisateur

D-Link

D-Link DSL-504G Manuel utilisateur

D-Link

D-Link DIR-827 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité