CYBEX AUTOVIEW COMMANDER - Instructions d'installation et d'entretien
©1999 Cybex Computer Products Corporation. All rights reserved.
IBM, PC, PC/AT and PS/2 are registered trademarks of International Business Machines Corporation.
Microsoft and Kensington are registered trademarks of their respective companies. Logitech, Mouseman and
Trackman are trademarks of Logitech, Inc. Cybex is a registered trademark of Cybex Computer Products
Corporation. AutoView, Commander, AutoBoot, RSP, 4xP, 1xP and all part numbers are trademarks of Cybex
Computer Products Corporation. IntelliMouse is a trademark of Microsoft Corporation.
AutoView Commander
Installer/User Guide
Cybex Computer Products International Ltd.
Cybex House
Shannon Free Zone
Shannon, Co. Clare, Ireland
(Tel) 00353 61 471 877 (Fax) 00353 61 471 871
www.cybex.ie
AutoView Commander Installer/User Guide
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance may void the user's authority to
operate the equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designedtoprovidereasonableprotectionagainstharmfulinterferencewhen
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
This digital apparatus does not exceed the Class A limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
Le présent appareil numérique n'émet pas de bruits radioélectriques
dépassant les limites applicables aux appareils numériques de la classe A
prescritesdansleRèglementsurlebrouillageradioélectriqueédictéparle
Ministère des Communications du Canada.
FCC Notification
Canadian Notification
Table of Contents
Chapter 4 - On-Screen Display Operations
Activating OSD ...................................................................................................................................... 13
The OSD Window .................................................................................................................................. 14
The Command Menu ........................................................................................................................... 15
Basic Channel Maintenance ............................................................................................................. 16
The ID Window ...................................................................................................................................... 18
Administrator Functions ..................................................................................................................... 20
Chapter 6 - Appendices
A: Specifications .................................................................................................................................... 27
B: Pairing .................................................................................................................................................. 28
C: Troubleshooting................................................................................................................................ 34
D: Problem Report................................................................................................................................. 39
Chapter 5 - Channel Scanning
Choosing a Scanning Method .......................................................................................................... 23
Setting the Scanning Order ............................................................................................................... 24
Turning Scanning On and Off........................................................................................................... 24
Setting the Scanning Dwell Time .................................................................................................... 25
Scanning and Security ......................................................................................................................... 26
Chapter 2 - Installation
Basic Install ................................................................................................................................................ 5
Advanced Install ....................................................................................................................................... 8
Chapter 1 - Product Overview
Feature Overview ...................................................................................................................................... 1
Compatibility ............................................................................................................................................. 3
Chapter 3 - Basic Operations
Overview ...................................................................................................................................................... 9
Keyboard Control .................................................................................................................................. 10
Keyboard Switching ............................................................................................................................. 11
System Control & Maintenance ....................................................................................................... 12
AutoView Commander Installer/User Guide
INSTRUCTIONS: The exclamation mark within an equilateral tri-
angle is intended to alert the user to the presence of important oper-
ating and maintenance (servicing) instructions in the literature ac-
companying the appliance.
DANGEROUS VOLTAGE: The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the product's
enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.
PROTECTIVE EARTHING TERMINAL: A terminal which must be
connected to the earth prior to making any other connections to
the equipment.
POWER ON: This symbol indicates the principle on/off switch is in
the on position.
POWER OFF: This symbol indicates the principle on/off switch is in
the off position.
Product Overview
1
Feature Overview
The AutoView Commander allows you to control up to 64 PCs with one
keyboard, monitor and mouse. Each computer can be up to 30 feet away
fromtheAutoView.The AutoViewworkswithIBMPC/AT andPS/2systems,
and 100% compatible machines with support for VGA, SVGA, XGA and
XGA-II video. PS/2 keyboard and PS/2 mouse peripherals are supported
through the rear of the unit.
AnAutoView unit will supportfromoneto eight attachedPCs,orchannels.
If more than eight channels are needed, multiple units can be cascaded
together for expansion. Up to 2 tiers of units can be connected for a total
of 64 attached computers in one system.
The AutoBoot feature boots all attached servers during initial power up or
after a power failure. PCs are booted transparently without operator
intervention,andmay be powered uponeatatime or all at once.Whenthe
power stabilizes, a channel may be selected. The first available channel is
automatically selected upon power-up of the base AutoView.
Configure and control your AutoView with on-screen menuing! Name
your computer channels anything you wish, then select the desired
computer from an easy-to-use menu. Secondary menus let you configure
and initiate channel scanning and other system features.
Use the advanced two-level security feature to configure and control
server access for every type of user in the system. The administrator has
full access privileges; individual users can have viewing or viewing/
editing capability for each attached server.
The AutoView offers full support for the Microsoft IntelliMouse.
AutoBoot
technology
Expansion for up
to 64 computers
On-screen display
capability
1
Advanced security
for total control
over system access
IntelliMouse
support
AutoView Commander Installer/User Guide
TheOSD Configuration Utility allowstheadministratorto easily configure
and download a channel list with defined users and access privileges to
the entire system. This utility will also read and save your current
configuration for extra security.
In addition to using the on-screen menus, you can switch computer
channels in one of three easy ways: via the AutoView channel push-
buttons, with the Scan button or with a simple keyboard sequence.
AutoView’s “Keep Alive” feature allows attached servers to power the unit
in the event of an AutoView power failure. This prevents attached PCs
from locking up and keeps you from losing time and data.
For added compatibility with your current equipment, AutoView features
PS/2 mouse translation capability. Operated through the AutoView, your
PS/2 mouse will work with any attached PC - regardless of whether the
computer is serial or PS/2 mouse compatible!
A built-in scanning feature allows you to automatically monitor, or scan,
your PCs without intervention. When keyboard activity is detected,
scanningissuspended until all activity stops. Scanning thenresumeswith
the next channel in sequence.
Indicator LEDs give you constant readings on the status of your AutoView
unit. Status, scanning and channel LEDs take the guesswork out of system
operation and diagnostics.
A typical AutoView configuration is shown below.
2
Push-button &
keyboard switching
PS/2 mouse
translation
Built-in scanning
capabilities
Status indicator
LEDs
“Keep Alive”
feature
OSD Configuration
Utility
3
The AutoView requires a PS/2 mouse and keyboard. The following mice
are known to be compatible:
IBM PS/2-style Logitech Trackman
Kensington Microsoft Serial-PS/2 mouse
Logitech Mouseman (PS/2) Microsoft IntelliMouse
Other manufacturers' mice may operate with the AutoView. If you
experience problems using an untested mouse, contact Cybex Technical
Support with the manufacturer and model number of the mouse.
If you wish to use XGA or XGA-II video, you will need to purchase an
adaptor available through Cybex.
PS/2 peripherals
Compatibility
XGA/XGA-II
support
Product Overview
AutoView Commander Installer/User Guide
5
Installation
2
Basic Install
1. Power down all computers that will be part of your AutoView
system.
Connecting your Peripherals
2. Locate your PS/2 keyboard, VGA video monitor and PS/2 mouse.
3. Plug your VGA monitor cable into the port labeled on the back of
your AutoView. Plug your PS/2 keyboard cable and your PS/2 mouse
cable into the ports labelled and respectively.
SETUP
A
E
USER
VGA MONITOR CABLE
PS/2 MOUSE CABLE
PS/2 KEYBOARD CABLE
AutoView Commander Installer/User Guide
Connecting Computers to the AutoView
4. Locateyourfirst input cable. It will have a 25-pin “D”connector at one
end. Plug this cable into any lettered channel port on the rear of the
AutoView. The other end of the input cable will have five connectors:
a 15-pin “HDD” connector for your video, a 5-pin DIN/6-pin miniDIN
connector for an AT or PS/2 keyboard connection, and a 9-pin serial/
6-pin miniDIN connector for a serial or PS/2 mouse connection. The
PS/2 mouse connector is designated by a yellow band or mouse icon.
Use only the keyboard and mouse connectors which are
appropriate for your PC, and leave the others unconnected.
Plug these connectors into the matching ports on your computer.
5. Locate your next input cable. Repeat step 4 until all computers are
properly attached to the AutoView.
POWER
100-240V
MADEIN USA
G
H
E
F
C
D
A
B
PATENTPENDING
T2A,250 VAC
USER
MOUSE PORT KEYBOARD PORT
VIDEO PORT
6
Autres manuels pour AUTOVIEW COMMANDER -
1
Table des matières
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
