CyberPower OLS6000ERT6UA Manuel utilisateur
User’s Manual
OLS6000ERT6UA
OLS10000ERT6UA
Cyber Power Systems, Inc.
www.cyberpower.com K01-C000653-00
IMPORTANT SAFETY INSTRUCTIONS..............................................................................................1
UNPACKING......................................................................................................................................... 3
HARDWARE INSTALLATION ............................................................................................................6
RACKMOUNT INSTALLATION...................................................................................................................... 6
VERTICAL/TOWER INSTALLATION ...........................................................................................................8
OVERVIEW ...................................................................................................................................... 10
POWER MODULE FRONT/REAR PANEL DESCRIPTION................................................................ 10
BATTERY MODULE FRONT/REAR PANEL DESCRIPTION ............................................................
1
BATTERY MODULE CONNECTION ......................................................................................................... 12
ELECTRICAL INSTALLATION......................................................................................................... 13
POWER WIRES INSTALLATION................................................................................................................ 13
EPO CONNECTION ........................................................................................................................................ 15
UPS SYSTEM STARTUP ................................................................................................................... 16
OPERATION...................................................................................................................................... 17
DISPLAY PANEL .............................................................................................................................................. 17
OPERATING MODES...................................................................................................................................... 18
LCD FUNCTION TREE................................................................................................................................... 20
PARALLEL FUNCTION.................................................................................................................................. 26
TROUBLESHOOTING ...................................................................................................................... 30
BATTERY MAINTENANCE .............................................................................................................. 33
TECHNICAL SPECIFICATIONS....................................................................................................... 34
TABLE OF CONTENTS
1
1
This manual contains important instructions. Please read and follow all instructions
carefully during installation and operation of the unit. Read this manual thoroughly before
attempting to unpack, install, or operate the UPS.
Installation
• This is permanently connected equipment, and it must be installed by qualified maintenance
personnel.
• Condensation may occur if the UPS is moved directly from a cold to a warm environment.
The UPS must be absolutely dry before being installed. Please allow an acclimatization time
of at least two hours.
• Do not install the UPS near water or in damp environment.
• Do not install the UPS where it would be exposed to direct sunlight or near heat.
• Do not connect appliances or items of equipment which would overload the UPS (e.g. laser
printers, etc.) to the UPS output.
• Do not block ventilation openings in the UPS’s housing. Ensure allow at least 0.5m of space
on front and rear of the UPS.
• Connect UPS with the earth reliably before connecting to the building wiring terminal, and
external battery source must also be earthed.
• An integral single emergency switching device which prevents further supply to the load by
the UPS in any mode of operation should be provided in the building wiring installation.
• An appropriate disconnect device as short-circuit backup protection should be provided in
the building wiring installation.
• The equipment is powered by two sources: the mains source, the internal battery or the
external battery source.
• With the installation of the equipment, the sum of the leakage current of the UPS and the
connected load does not exceed 5% of rated value of input current.
Operation
• Do not disconnect the main cable on the UPS or the building wiring terminals during
operation since this would remove the protective earth from the UPS and all connected
loads.
• The UPS output terminal block may still be electrically lived from internal current source
(batteries) even if the UPS is not connected to the building wiring terminal.
• In order to fully disconnect the UPS, turn the input breaker in the "OFF" position first, and
then disconnect the mains lead.
• Indiscriminate operation of switches may cause output loss or damage to equipment. Refer
to instruction before conducting any control.
• While the UPS work as a parallel system, the external parallel cable should be reinforced
insulation.
• Ensure that no liquid or other foreign objects can enter the UPS.
IMPORTANT SAFETY INSTRUCTIONS
2
IMPORTANT SAFETY INSTRUCTIONS
Maintenance, Servicing and Faults
• Do not remove the enclosure since the UPS operates with hazardous voltages. It is to be
serviced only by qualified maintenance personnel.
• Caution! Risk of electric shock. Even after the unit is disconnected from the mains power
supply (building wiring terminal) components inside the UPS are still connected to the
battery which are potentially dangerous.
• Before carrying out any kind of service or maintenance, isolate UPS and disconnect the
batteries. Verify that no current and no hazardous voltage exists in the capacitor or BUS
capacitor.
• Batteries must be replaced only by qualified personnel.
• Batteries have a high short-circuit current and pose a risk of shock. Take all precautionary
measures specified below and any other necessary measures when working with batteries:
- remove all jewelry, wristwatches, rings and other metal objects
- use only tools with insulated grips and handles.
• When changing batteries, replace with the same quantity and the same type of batteries.
• Do not attempt to dispose of batteries by burning them. It could cause explosion.
• The UPS may be connected to Battery pack. Proper disposal of batteries is required. Refer to
your local codes for disposal requirements.
• Do not open or destroy batteries. Effluent electrolyte can cause injury to the skin and eyes. It
may be toxic.
• In order to avoid fire hazards when replacing the fuse, only use the same type and the same
spec of fuse.
Transport
• Please transport the UPS only in the original packaging to protect against shock and impact.
Storage
• The UPS must be placed in the room where is ventilated and dry.
3
UNPACKING
Package List
The package should contain the following items.
Inspect the contents upon receipt. Do not turn on the unit and notify the carrier and the
dealer immediately if there is any damage or lacking of some parts.
Box of Power Module
See page 4 for details
Box of Battery Module
See page 5
4
UNPACKING
The box of Power Module should contain the following items:
PowerPanel® Business software is available on our website.
Please visit www.cyberpower.com and go to the Software Section for free download.
Power Module Rackmount Rails
USB Communication CableUser’s manual Flat Head Screws:
M4X8L (8)
Pan head screws:
M5X12L (12)
Battery Cable Terminal (9)Rackmount Ears
(Stands)
Parallel Cable
Plastic
Washers (8)
Screw Hole Dust
Covers (8)
Binding Head Screws:
M4X8L (6)
M5 Nut (8)
5
UNPACKING
The box of Battery Module should contain the following items:
Battery Module Rackmount Rails
Flat Head Screws:
M4X8L (8)
Pan Head Screws:
M5X12L (12) Binding Head Screws:
M4X8L (6)
M5 Nut (8)
Rackmount Ears
(Stands)
Plastic
Washers (8)
Screw Hole Dust
Covers (12)
Terminal (6)
6
HARDWARE INSTALLATION
These versatile UPS systems can be mounted in a rackmount or vertical tower orientation. This
versatility is especially important to growing organizations with changing needs that value
having the option to position a UPS on a floor or in a rackmount system. Please follow the
instructions below for the respective mounting methods.
RACKMOUNT INSTALLATION
Step 1: Rackmount ears installation
(1) Attach the two rackmount ears to the UPS using the provided screws M4X8L*8pcs.
(2) Insert dust cover into the rackmount ear screw holes that are not being used.
(1)
(2)
CAUTION! To prevent the risk of fire or electric shock, only use the supplied hardware
to attach the mounting brackets.
7
Step 2: Rackmount rails Installation
(1) The rails adjust to mount in 48-cm (19-inch) panel racks from 46.4 to 73.8cm (18.3 to 29
inches) deep. Select the proper holes in the rack for positioning the UPS in the rack. The
rails take up position 1 through position 3.
(2) Attach the rackmount rail to your rack with two M5X12L screws, two plastic washers, and
two M5 nut at the front of the rack. (Located in position 1 & position 2; It can also located
in position 1 & position 3 or position 2 & position 3 alternatively). Do not tighten the screws.
Adjust the rail size on the rail assembly of your rack. Secure the rail to the rear of the rack
with two M5X12L screws, two plastic washers, and two M5 nut. Tighten all screws at the
front and rear of the rail. Once completed, perform the same steps for assembling the
other rackmount rail.
Step 3: Install the UPS on the rack
(1) Place the Power Module on a flat stable surface with the front of the unit facing toward
you. Secure the Power Module to your rack with four M5X12L screws at the front of the
rack. (Located in position 2 & position 8).
HARDWARE INSTALLATION
3U
2U
1U
position 9
position 8
position 7
position 6
position 5
position 4
position 3
position 2
position 1
position 3
position 1
(1) (2)
position 2
position 8
CAUTION! The Battery module must be installed below the Power module.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels CyberPower UPS
CyberPower
CyberPower CP900AVR Manuel utilisateur
CyberPower
CyberPower GX1500U Manuel utilisateur
CyberPower
CyberPower OL1000RTXL2U Manuel utilisateur
CyberPower
CyberPower BPSE240V47A Manuel utilisateur
CyberPower
CyberPower 649532110001 Manuel utilisateur
CyberPower
CyberPower CP685AVR Manuel utilisateur
CyberPower
CyberPower BRG1350AVRLCD Manuel utilisateur
CyberPower
CyberPower 649532022069 Manuel utilisateur
CyberPower
CyberPower CyberShield CS24U12V Manuel utilisateur
CyberPower
CyberPower OLS6000ECXL Manuel utilisateur
CyberPower
CyberPower 649532722037 Manuel utilisateur
CyberPower
CyberPower PR1000LCDRT2U Manuel utilisateur
CyberPower
CyberPower PR3000LCDRT2U Manuel utilisateur
CyberPower
CyberPower CP900EPFCLCD Manuel utilisateur
CyberPower
CyberPower LE850G Manuel utilisateur
CyberPower
CyberPower BC900C Manuel utilisateur
CyberPower
CyberPower CPS1500AVR Manuel utilisateur
CyberPower
CyberPower BPSE240V82A Manuel utilisateur
CyberPower
CyberPower 649532607006 Manuel utilisateur
CyberPower
CyberPower BPSE36V45A Manuel utilisateur
Manuels UPS populaires d'autres marques
Pylontech
Pylontech Victron & Pylontech US5000 Manuel utilisateur
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur
Mecer
Mecer ME-1000-WTU Manuel utilisateur
Mustek
Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation
Emerson
Emerson Liebert NXL series Manuel utilisateur
MAKELSAN
MAKELSAN BOXER SERIES Manuel utilisateur
