Cutech 80100-CT Manuel utilisateur
80100-CT UNIVERSAL STAND
ASSEMBLY
Place upper brace, long, inside upper leg piece .
NOTE: Upper brace has two large, oval holes in each end , these holes should be on top when leg stand
is completely assembled.
Align holes on the upper brace with the holes on the leg piece. Insert two carriage bolts and hand
tighten using hex nuts.
Place lower leg piece inside upper leg brace. Place lower brace, long, on top of both leg pieces.
Align holes on all three pieces. Insert two carriage bolts and hand tighten using hex nuts.
Attach a second upper leg piece to the outside of upper race using two carriage bolts and hex nuts.
Next , attach lower leg piece to the inside of upper leg piece placing lower brace on top of both leg
pieces ( also on the inside of the leg stand ) . Insert two carriage bolts and hand tighten using hex
nuts.
Repeat the above steps once. This completes two of the four sides of the leg stand.
Place upper brace, short, inside upper leg piece.
NOTE: Upper brace, short, has two large, oval holes in each end; these holes should be on top when leg
stand is completely assembled.
DESCRIPTION
QTY
Upper Brace, Long
2
Upper Brace, Short
2
Lower Brace, Long
2
Lower Brace, Short
2
Upper Leg
4
Lower Leg
4
Rubber Foot
4
Carriage Bolt, M8x1.25-16
32
Carriage Nut, M8x1.25
32
2
Align holes on upper brace, long, with the holes on the upper leg piece. Insert two carriage bolts and
hand tighten using hex nuts.
Repeat the above step on the opposite side.
On the inside of the leg stand, place lower brace, short, on top of both the upper and lower leg pieces.
Insert two carriage bolts and hand tighten using hex nuts.
Repeat the above step on the opposite side.
Place one rubber foot on the bottom of each lower leg piece.
Using a wrench, securely tighten all hex nuts. This completes the leg stand.
MOUNTING THE BOARD TO THE STAND
(FOR 40100-CT/40100H-CT/40300H-CT/40700-CT/40160H-CT)
NOTE: The board (not included) may be required to be attached your machine to the stand. Prepare a
piece of 5/8 " to 3/4" thick plywood to the top dimensions of the stand (23 “x 14 “) or a bit larger. Place the
board onto the stand . Fasten the board in place to the stand with screws or bolts (not included). Fasten the
machine on the board with screws and washers. (not included) SEE FIG 1 & 2.
MOUNTING PLANER TO THE STAND
(FOR 40200H-CT/40600H-CT)
WARNING! TO AVOID serious injury, death, or damage to the machine. Do not mount any machinery to
the stand until the stand is completely assembled, do not run the machine until it’s mount on the stand
securely.
Mounting holes in your planer line up with the four pre-bored holes in the stand's four corners, Just fasten
the planer onto the stand with nuts and bolts. SEE FIG 3.
FIG 1 FIG2 FIG3
For technical support, email support@cutechtools.us or call 858-886-7333
Table des matières
Autres manuels Cutech Support et étagère
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
