CTC Union JB330 Series Manuel utilisateur

JB330 Series Switch BoxJB330 Series Switch Box

12 Triaxial Inputs12 Triaxial Inputs

Product ManualProduct Manual

• Introduction...................................................................3

• Product Description...........................................................3

• Product Dimensions...........................................................4

• Mounting Instructions .........................................................5

• Conduit Entry .................................................................6

• Grounding ....................................................................7

• Sensor Installation ............................................................9

• Post-Installation Testing..................................................... 12

• Maintenance ................................................................ 13

• Warranty & Refund .......................................................... 14

T  C

I

CTC switch box solutions allow for the monitoring of remotely-mounted vibration

sensors, which would otherwise be restricted to human access due to safety

considerations.

JB330 Series Switch Box Overview: Four to 12 triaxial sensor inputs (12 to 36

measurement channel outputs), stainless steel slope top enclosure

The JB330 Switch Box is a common cable termination point for bringing

compatible cables for triaxial sensors into a switch box for routine data collection

with portable data collectors. JB series enclosures are designed to have field-

input cabling installed behind the board. A flip-down panel allows the user to wire

connections on location. The JB series also features an IEPE bias indicator light

built into the box itself, which can be used to indicate errors in the field wiring or

the sensor.

Rated for NEMA 4X (IP66), the JB330 is resistant to hose-directed fluid

and corrosion. The box can also withstand harsh environments, including

temperatures ranging from -58°F to 180°F (-50°C to 82°C). A key latch is installed

on the door, allowing the box to be sealed from the elements when not in use.

If a continuous output application is desired, that can be easily accomplished by

purchasing the optional CTC accessory “T” plug, part number JB933-1A.

P D

Measurement

Location Card

Data Collector

Access (BNC)

Switch

Quick

Connect

Option

Screw

Terminal

Option

Data Collector

Access (4 pin)

Input Terminal Strip Options

Bias

Indicator

Light

Figure 1. Dimensions

Figure 2. Diagram

Front View Side View

M I

Note: If you have purchased a switch box without cable entries provided, you

should add your own entry prior to mounting the modular switch box. CTC does

not recommend drilling holes in the top of the enclosure due to access and

moisture concerns.

Mounting

Holes

0.31 in./7.95 mm

Figure 3. Sloped Top Vibration Switch Box Rear View

C E

If you have purchased a switch box without cable entries provided, you should

add your own entry prior to mounting the enclosure. CTC does not recommend

putting holes in the top of enclosures as it will cause restricted access to the

wire termination connection points and also allow possible moisture ingress.

Note: To prevent a buildup of condensation inside the enclosure, provide drainage

by drilling a hole in the lowest point of the conduit.

Correct

Figure 4. Conduit Entry for Switch Box

Drill Drain

Hole Here

G

Ensure the shield ground wire on the JB330 Series Switch Box is grounded to

earth ground.

A. Mounting to Earth Ground

When mounting JB330 Series Switch Boxes to earth ground (such as an I-Beam),

no additional steps are necessary, as the enclosure is grounded internally.

Figure 5. Switch Box (JB330) Earth Ground

G

B. Mounting to Non-Grounded Structure

When mounting the switch box to a non-grounded structure, ensure the shield

ground wire or customer-supplied ground wire is tied to a source of earth ground.

Figure 6. Ground Wire Placement

S I

Installation of Sensors/Signal Input Cable

1. Feed blunt-cut end through the cable entry at the bottom of the enclosure.

Note: It is recommended that cables are marked on both ends.

For cord grip cable entry, take off the cord grip cover with bushing and run cable

through it then into the enclosure, hand-tighten cord grip cover to base to prevent

damage of cord grip.

1. Strip outer jacket of cable back 1¼ in. and remove all of the shielding.

2. Separate the internal wires from the shield.

3. Strip red, green, white, and black insulation back ¼ in.

Figure 8. Bottom View with

Cord Grips Installed

Figure 7. Front View

Figure 9. Stripped Wire

(-)

Shield / Drain Wire

(+) Channel Y

(+) Channel X

(+) Channel Z

Figure 10. Field Wiring for Four-Conductor Triaxial Sensor Inputs

GND

SENSOR #1 SENSOR #2

GND

SENSOR #3

GND

SENSOR #4

GND

SENSOR #5

GND

SENSOR #6

GND

SENSOR #7

GND

SENSOR #8

GND

SENSOR #9 SENSOR #10

GND

SENSOR #11

GND

SENSOR #12

GND

Sensor Inputs

Green = Positive X Axis

Red = Positive Y Axis

White = Positive Z Axis

Black = Common

Grey = Shield (Ground)

Inputs

S I

4. Locate the appropriate plug (identified by channel number), remove it, and

install the wires using a small flathead screwdriver. Push plug back into location.

Orientation is as follows:

a. Green insulated conductor wire is connected to Channel X.

b. Red insulated conductor wire is connected to Channel Y.

c. White insulated conductor wire is connected to Channel Z.

d. Black insulated conductor wire is connected to (-).

e. Shield drain wire is connected to ground (GND).

GND

SENSOR #1 SENSOR #2

GND

SENSOR #3

GND

SENSOR #4

GND

SENSOR #5

GND

SENSOR #6

GND

SENSOR #7

GND

SENSOR #8

GND

SENSOR #9 SENSOR #10

GND

SENSOR #11

GND

SENSOR #12

GND

Sensor Inputs

Green = Positive X Axis

Red = Positive Y Axis

White = Positive Z Axis

Black = Common

Grey = Shield (Ground)

Inputs

Table des matières

Autres manuels CTC Union Changer

CTC Union

CTC Union IGS-803SM Manuel utilisateur

CTC Union

CTC Union FSW-2104W Manuel utilisateur

CTC Union

CTC Union GSW-3208M Manuel utilisateur

CTC Union

CTC Union IFS?402F Manuel utilisateur

CTC Union

CTC Union SB102 Series Manuel utilisateur

CTC Union

CTC Union SB142 Manuel utilisateur

CTC Union

CTC Union IFS+402GSM-4PHE24 Manuel utilisateur

CTC Union

CTC Union JB130 Series Manuel utilisateur

CTC Union

CTC Union IGS-804SM-SE-8PHE Manuel utilisateur

CTC Union

CTC Union ITP-800A Manuel utilisateur

CTC Union

CTC Union SB202 Series Manuel utilisateur

CTC Union

CTC Union PHB-200 Manuel utilisateur

CTC Union

CTC Union VRM01/24 Manuel utilisateur

CTC Union

CTC Union FRM220A-1000EAS/X Manuel utilisateur

CTC Union

CTC Union GSW-3208M2 Manuel utilisateur

CTC Union

CTC Union GSW-3208M1 Manuel utilisateur

CTC Union

CTC Union FRM220A-MSW-202 Manuel utilisateur

CTC Union

CTC Union IGS-812SM Series Manuel utilisateur

CTC Union

CTC Union IGS+803SM-8PH Manuel utilisateur

CTC Union

CTC Union GSW-1005MS Manuel utilisateur

CTC Union

CTC Union JB230 Series Manuel utilisateur

CTC Union

CTC Union IFS?401F Manuel utilisateur

CTC Union

CTC Union IQS-402XSM-4PH Manuel utilisateur

CTC Union

CTC Union JB320 Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur