CTC Union STE-10 Manuel utilisateur
OPERATION MANUAL
Table of Contents
i
CHAPTER 1
1.0 Introduction ..................................................................... 1
1.1 Features ………………………………………………….. 1
1.2 Specifications ................................................................... 2
1.3 Configuration ................................................................... 4
1.4 Configuration with Telnet ................................................. 8
1.5 Raw Data Server Mode .................................................... 9
1.6 Telnet IAC Data Server Mode ......................................... 16
1.7 Terminal Server Mode .................................................... 17
1.8 Auto Connect After Power Up Mode .............................. 20
CHAPTER 2
2.0 Application Examples ...................................................... 23
2.1 Raw Data Server Application ....................................... 23
2.2 Terminal Server Application ........................................ 24
2.3 Auto Connect Application ........................................... 26
APPENDIX
A.1 RS-232 Port Pin Definition ............................................. 29
A.2 RJ-45 Ethernet Pin Definition ......................................... 29
A.3 Null Modem Cable Pinout ............................................... 30
Table of Contents
ii
This page left blank intentionally.
Chapter 1: Configuration and Operation
1
1.0 Introduction
The STE-10 Serial Access Unit is a low cost, compact, serial
access server or terminal server for connecting asynchronous serial
devices (RS-232) over Ethernet (10Base-T) using a TCP/IP protocol
stack. The STE-10 may operate in either a client mode or as a server,
allowing connection of serial data directly over a LAN or WAN.
Configuration may be performed either via the DB25 pin RS-232 port
with an ASCII terminal or via Telnet and Ethernet connection on the
RJ-45 LAN port. The serial port is DTE, which allows direct
connection to DCE equipment such as Modems. For connection to
other DTE equipment such as a PC or terminal, a NULL Modem or
crossover cable is required. One is provided with the unit.
1.1 Features
•Low cost, compact design.
•Serial connection over Ethernet.
•Operates in either server or client mode.
•Complete TCP/IP protocol stack (OSI Network Layer 3).
•Provides packetization of serial data.
Chapter 1: Configuration and Operation
2
1.2 Specifications
Hardware
•CPU Intel® 80188
•ROM 256K bytes Flash
•RAM 256K bytes DRAM
•LAN Interface IEEE802.3 10Base-T Ethernet, RJ-45
connector, DTE connection straight to HUB
•Serial interface EIA RS-232 ASYNC, DB25M connector
•Baud rates 1200, 2400, 4800, 9600, 19200, 38400,
57600, 115200, 230400, or 460800
•Data length 5, 6, 7, or 8 bits
•Parity None, Odd, or Even
•Stop bits 1 or 2 bits
•Handshaking None, RTS/CTS, or Xon/Xoff
Software
•Flash ROM Boot without network host; provision for easy
software upgrades
•Protocols TCP/IP, ARP, ICMP protocols
•Functions Telnet / Reverse Telnet
•Configuration Telnet or ASCII terminal direct or via Dial-in
•LED indicators Power, LAN Tx/Rx, Serial Tx and Rx
Chapter 1: Configuration and Operation
3
Ethernet connection: straight cable to HUB,
crossover cable to NIC
Ethernet activity indicator LED
Connect to
AC Adapter
Power
indicator
LED
RS-232 activity
LED indicators
RS-232 Async Port
D-type 25 pin Male
Config.
Switch
Chapter 1: Configuration and Operation
4
1.3 Configuration
Before any Ethernet connection is made to the STE-10, the
device must have a valid IP address, which is accessible through the
network. Initial IP setting is accomplished with a terminal connection
to the RS-232 serial port. Connect a serial terminal to the RS-232 port
of the STE-10 at 9600 baud, 8 bits, no parity and 1 stop bit. Since the
STE-10 is DTE and a terminal is also DTE, please use the provided
crossover cable. Set the configuration switch on the STE-10 to
"SETUP" and apply power.
If a serial terminal is not available, a PC with Windowsmay be
used along with the HyperTerminalprogram. To start and configure
HyperTerminalfollow these simple steps:
Using your mouse, browse to HyperTerminal; Start =>Programs
=>Accessories =>Communications =>HyperTerminal.
Double-click the "Hypertrm.exe" icon. Enter a name (such as
STE-10) and choose an icon for the connection. When the "Connect
to" dialogue box appears, click the down arrow on the "Connect
using:" pull-down tab and select "Direct to COMx" where "x" is the
COM port number that will connect to the STE-10.
Click the "OK" button and set the COM port parameters for; 9600
baud, 8 bits, no parity, 1 stop bit and no flow control. Refer to the
following page graphic.
Chapter 1: Configuration and Operation
5
Example of port setting under HyperTerminal.
An initial message like the one below will be displayed while the
port checks whether it is connected to a modem, followed by the main
configuration menu display.
CHECKING MODEM ABOUT 10 SECONDCHECKING MODEM ABOUT 10 SECOND
AT&C1V1AT&C1V1
Chapter 1: Configuration and Operation
6
If your connection is a direct one, your terminal should display
the first menu for the STE-10.
SERIAL DEVICE SERVERSERIAL DEVICE SERVER
a). DEVICE SETTINGSa). DEVICE SETTINGS
b). UPGRADE FIRMWAREb). UPGRADE FIRMWARE
c). GENERAL DIAGNOSTICc). GENERAL DIAGNOSTIC
SELECT:SELECT:
Main configuration menu, terminal mode.
Select option a): Device Settings
DEVICE SETTINGSDEVICE SETTINGS
a). DEVICE IP ADDRESSa). DEVICE IP ADDRESS <192.168.2.1><192.168.2.1>
b). DEVICE SUBNET MASKb). DEVICE SUBNET MASK <255.255.255.0><255.255.255.0>
c). DEVICE NAMEc). DEVICE NAME <STE-10><STE-10>
d). DEVICE PASSWORDd). DEVICE PASSWORD <><>
e). MODE SETTINGSe). MODE SETTINGS <<RAW SERVER>RAW SERVER>
f). GATEWAY ADDRESSf). GATEWAY ADDRESS <0.0.0.0><0.0.0.0>
g). LOAD DEFAULT SETTINGSg). LOAD DEFAULT SETTINGS
h). APPLY AND SAVE SETTINGSh). APPLY AND SAVE SETTINGS
q). PREVIOUS MENUq). PREVIOUS MENU
SELECT:SELECT:
Table des matières
Autres manuels CTC Union Matériel réseau
CTC Union
CTC Union IMC-100-PD Manuel utilisateur
CTC Union
CTC Union INJ-G30 Manuel utilisateur
CTC Union
CTC Union SC150 Series Manuel utilisateur
CTC Union
CTC Union IPM-E1 Series Manuel utilisateur
CTC Union
CTC Union VDSM2-1524 Manuel utilisateur
CTC Union
CTC Union IP DSLAM for ADSL IPDSLAM-A8/A16 Manuel utilisateur
CTC Union
CTC Union FRM220-TM-10GMUX Manuel utilisateur
CTC Union
CTC Union FMUX101 Manuel utilisateur
Manuels Matériel réseau populaires d'autres marques
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuel utilisateur
Yudor
Yudor YDS-16 Manuel utilisateur
D-Link
D-Link ShareCenter DNS-320L Manuel utilisateur
Samsung
Samsung ES1642dc Instructions d'utilisation
Honeywell Home
Honeywell Home LTEM-PV Instructions de montage
