CTA ADD-ADMA Manuel utilisateur

Articulating Desk Mount Arm with VESA Plate

ADD-ADMA

CONTENTS:

INSTRUCTIONS:

2A. When the C-Clamp is securely

attached to a surface, use the

provided security tool (C), attach to

security component, and rotate

closewise to put the C-Clamp in an

‘locked’ state. To loosen, rotate

counterclockwise with the security

tool.

Remove arm (D) from the

base clamp mount. Repeat

steps in reverse order to

re-install connection

2B. Align the (2) dimples on the underneath of the

security tool into the two holes on the security

component on the clamp as shown above

2C. Rotate counter-clockwise to

loosen and place the clamp in an

‘unlocked’ state. Continue rotating

until there is enough slack to rotate

the knob.Turn it clockwise to tighten

and place the clamp in a ‘locked’

state.

BASE CLAMP SECURITY SETUP

BASE MOUNT INSTALLATION ARM & BASE CLAMP

ADJUSTMENTS

If you need to remove the arm

from the base clamp, take the

provided tool (B), rotate, and

loosen connection.

Find the included base

pad (E) and peel off the

backing. Align to the

underneath of the

C-Clamp (D) and apply

pad. While the clamp is in unlocked mode, rotate the

knob at the bottom (as shown above) to loosen

or securely tighten to the table top.

ALIGNING SECURITY TOOL WITH SECURITY COMPONENT

Articulating Desk Mount Arm with VESA Plate

ADD-ADMA

Each hinge of the product can be

adjusted easily with the provided tool (A).

Loosen to adjust and securely tighten

after preferred position is set.

When all hinges and joints are tightened, do not attempt to

forcibly flex the angles or positioning without loosening. Any

attempt to do so will possibly have an effect on product integrity

and CTA and manufacturer will not be responsible for any

mishandling.

JOINT ADJUSTMENTS

When routing cables from

device to the power source, use

provided clips (F) as shown to keep

the cables organized and tight to

the arms to avoid any slack.

CABLE

ROUTING

Table des matières

Autres manuels CTA Support et étagère

CTA

CTA PAD-CHKBM10 Manuel utilisateur

CTA

CTA PAD-ADMA Manuel utilisateur

CTA

CTA PAD-UATPB2 Manuel utilisateur

CTA

CTA ADD-2VDMB Manuel utilisateur

CTA

CTA PAD-SHFS Manuel utilisateur

CTA

CTA PAD-ASKP Manuel utilisateur

CTA

CTA PAD-PARAFP Manuel utilisateur

CTA

CTA PAD-UGT Manuel utilisateur

CTA

CTA PAD-PARAF1 Manuel utilisateur

CTA

CTA PAD-PARAF1GT Manuel utilisateur

CTA

CTA PAD-PARAFU Manuel utilisateur

CTA

CTA PAD-FTSU Manuel utilisateur

CTA

CTA PAD-TAM Manuel utilisateur

CTA

CTA PAD-DSGK Manuel utilisateur

CTA

CTA PAD-CFWM Manuel utilisateur

CTA

CTA ADD-USGTWP Manuel utilisateur

CTA

CTA PAD-HSKSBAE Manuel utilisateur

CTA

CTA AUT-VDMC Manuel utilisateur

CTA

CTA ADD-PARAFS Manuel utilisateur

CTA

CTA PAD-TPADM Manuel utilisateur

CTA

CTA PAD-ASK13B Manuel utilisateur

CTA

CTA PAD-SWM Manuel utilisateur

CTA

CTA PAD-TAM Manuel utilisateur

CTA

CTA PAD-MSPC10 Series Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur