CS Instruments DS 300 mobile version Manuel utilisateur

V4_03_2011

Instruction manual

Multi-channel display and data logger

- 2 -

Table of contents

Page

Introduction 2

Instruments description 3

Technical data 4

Key features 5

Calibration/adjustment 5

Safety instructions 5

DS 300 with VA 400 consumption sensor 6-7

DS 300 with FA 410 dewpoint sensor 8

Sensor connection 9

Flexible current supply 9

Survey operation menu 10

Operation 11-16

Sensor settings 16-18

System status 19

Warranty 19

Scope of delivery 19

Order information 20

Notes 21-23

Contact 24

Introduction

Dear CS customer,

You have made the right decision by choosing a measuring instrument from CS Instruments

GmbH. Thousands of customers buy our high standard products every year. There are a few

good reasons for doing so:

•The cost-performance ratio - reliable quality at a fair price.

•We have the ideal solutions for your measuring tasks based on our expert

experience gained over 20 years.

•Our high quality standard.

•Of course, our instruments carry the CE symbol required by the EU.

•We issue calibration certificates and hold seminars.

•Also after the purchase we do not leave you out in the cold - we offer a good

after sales service.

measuring instrument conforms with DIN EN 61326

- 3 -

1. Instruments description

•Energy analysis

•Consumption measurement

•Leakage calculation

The all-rounder DS 300 mobile version in a robust case is the ideal multifunction measuring

instrument for the mobile use. The internal rechargeable battery enables mains-independent

measurements of up to 4 hours.

Up to 6 parameters can be recorded at the same time (consumption, pressure dew point,

current consumption, pressure, temperature …).

Special features:

•All relevant measured data at a glance:

- Actual air consumption in

m³/h or m³/min

- Total air consumption in m³

- Pressure dew point in °Ctd

- Line pressure in bar

- Current consumption in A

- Temperature in °C

•Data logger for 1 million measured values

•Min-, Max-, average values attainable

on-site without any PC

•The data transfer to the PC is effected

via USB interface

- 4 -

2. Technical data

Case Dimensions: 265 x 220 x 150 mm

Sensor inputs 2 channel version: 2 inputs for consumption and dew point

sensors no analogue inputs

4 channel version: 2 inputs for consumption and dew point

sensors, 2 additional inputs for analogue

sensors 0/4…20 mA

6 channel version: 2 inputs for consumption and dew point

sensors, 4 additional inputs for analogue

sensors 0/4…20 mA

Interface USB to PC

Keypad 4 keys

Voltage supply 100 .… 240 VAC / 50-60 Hz / 10 VA

internal rechargeable battery (4 hours battery life)

charging time: 10 hours

Display Graphic display, 160 x 100 pixels, with back light

Accuracy Dew point: see sensor specifications

Consumption: see sensor specification

Pressure: 0.5 % F.S.

Current: 5 % < 25 A

2 % > 100 A

1 % > 250 A

0…20 mA: 0.01 mA

0…10 V: 0.01 V

Pt100: 0.5 °C

Pt1000: 0.5 °C

Measuring range Dew point: see sensor specifications

Consumption: see sensor specifications

Pressure: 0…16/40 bar

Current: 0…500 A

Pt100: -200…600 °C

Pt1000: -200…600 °C

Sensor connections ODU connection plug, 5-pole

Operating temperature 0 ... 50 ºC

Transport temperature -20 ... 70 ºC

Weight 2400 g

Data logger Up to 1,000,000 values

Programmable start time or manual start

Measuring rate: 1 s ... 1 h freely adjustable

Average value, Min./Max. value depending on protocol

- 5 -

3. Key features of DS 300 mobile version

•Graphic display for easy user interface

•Flexible power supply: 100…240 V AC/ 50…60Hz resp. internal rechargeable battery

•2 sensor inputs for CS consumption and dew point sensors (sensor connection 1 + 2)

•USB interface

•Data logger function for up to 1,000,000 values

•PC software for easy configuration and evaluation of the data

•Analogue input module (0…20 mA, 0…10 V, Pt100, Pt1000) (sensor connection 3, 4, 5

and 6)

4. Calibration/adjustment

At CS Instruments

According to DIN ISO certification of the measuring instruments we recommend to calibrate

and if applicable to adjust the instruments regularly at the manufacturer. The calibration

intervals should comply with your internal specificaton. According to DIN ISO we recommend

a calibration interval of one year for the instrument DS 300 including probes.

5. Safety instructions

Observe measuring ranges of the sensors!

Observe the admissible storage and transportation temperature as well as the

permitted operating temperature (e. g. protect the instrument from direct

insolation).

The manufacturer cannot be held liable for any damage which occurs as a

result of non-observance or non-compliance with these instructions. Should the

device be tampered with in any matter other than a procedure which is

described and specified in the manual, the warranty is cancelled and the

manufacturer is exempt from liability.

CS Instruments GmbH offers no gurantee for the suitability for any other

purpose and is not liable for errors which may have slipped into this operation

manual. CS Instruments GmbH is also not liable for consequential damage

resulting from the delivery, capability or use of this device.

We offer you to take back the instruments DS 300, which you would like to

dispose of.

Adjustments and calibrations should only be carried out by qualified employees

from the measurement and control technology branch.

- 6 -

6. DS 300 mobile version with VA 400 consumption sensor

Initiation

1. Connect consumption sensor VA 400 to channel 1 or 2

2. Switch on the instrument (DS 300 will recognize the consumption sensor VA 400

automatically)

3. The following parameters will be indicated: Flow in m³/h, m³/min, consumption in m³

resp. l, velocity in m/s

Necessary adjustments via keypad DS 300 (see page 16)

- Adjust inner diameter of the pipe (menu sensor adjustment/consumption)

ÆDS 300 automatically calculates the respective values for m³/h, m³/min and so on.

- Reference temperature and reference pressure (factory setting 20 °C, 1000 hPa):

All volume flow values (m³/h) and consumption values indicated in the display are

related to 20 °C, 1000 hPa (according to ISO 1217 intake condition)

0 °C and 1013 hPa (= standard cubic meter) can also be entered as a reference.

Do not enter the operation pressure or the operation temperature under reference

conditions!

Please read carefully before starting the device!

1. Do not exceed pressure range > 50 bar

2. Observe flow direction of the sensor

3. Adapter sleeve must be tightened with a torque

of 20-30 Nm

4. Observe minimum values for the inlet section

(15 x inner diameter) and for the outlet section

(5 x inner diameter)

For further information please see instruction

manual VA 400.

engraved

depth scale

safety ring

mounting depth = x+y

dA= outer diameter

x = dA

- 7 -

6.1 Technical data consumption sensor VA 400

Accuracy with

measuring section ±3 % m.v.

±2 % m.v.

via 5 point ISO precision calibration

Units freely selectable m³/h, m³/min, l/min, l/s, ft/min, cfm, kg/h, kg/min, kg/s

Inlet length 15 x inner pipe diameter

Outlet 5 x inner pipe diameter

Ball valve 1/2" stainless steel 1.4301

Operating temperature -20 to 70 °C

Storage temperature -40 to 80 °C

3 measured value per

VA 400 Flow in m³/h resp. m³/min, consumption in m³ bzw. l,

velocity in m/s

6.2 Measuring ranges consumption sensor VA 400

Tube inner diameter VA 400 Max.

(185,0 m/s) VA 400 HighSpeed (224,0

m/s)

Inch mm Measuring range

from ... to Measuring range

from ... to

1/4“ 6 DN 6 1.0 ... 157 l/min 2.0 ... 190 l/min

1/2“ 16.1 DN 15 3.5 ... 1516 l/min 6.0 ... 1836 l/min

3/4“ 21.7 DN 20 0.4 ... 178 m³/h 0.7 ... 215 m³/h

1“ 27.3 DN 25 0.6 ... 295 m³/h 1.1... 357 m³/h

1 1/4“ 36.0 DN 32 1.2 ... 531 m³/h 2.5 ... 644 m³/h

1 1/2“ 41.8 DN 40 1.5 ... 728 m³/h 3.0 ... 882 m³/h

2“ 53.1 DN 50 2.5 ... 1198 m³/h 4.6 ... 1450 m³/h

2 1/2“ 71.1 DN 65 5 ... 2187 m³/h 7 ... 2648 m³/h

3“ 84.9 DN 80 7 ... 3133 m³/h 12 ... 3794 m³/h

4“ 110.0 DN 100 12 ... 5279 m³/h 16 ... 6391 m³/h

5“ 133.7 DN 125 18 ... 7808 m³/h 24 ... 9453 m³/h

6“ 159.3 DN 150 25 ... 11097 m³/h 43 ... 13436 m³/h

8“ 200.0 DN 200 33 ... 17533 m³/h 50 ... 21230 m³/h

10“ 250.0 DN 250 52 ... 27429 m³/h 80 ... 33211 m³/h

12“ 300.0 DN 300 80 ... 39544 m³/h 100 ... 47881 m³/h

DIN 1945/ ISO 1217: 20°C, 1000mbar

5 point precision calibration with ISO certificate: order no. 3200 0001

special version for oxygen measurement: order no. 3200 0010

- 8 -

7. DS 300 mobile version with FA 410 dew point sensor

Initiation

1. Connect dew point sensor FA 410 to channel 1 or 2

2. Switch on the instrument (DS 300 will recognize the dew point sensor FA 410

automatically)

3. The following parameters will be indicated: dew point in °Ctd, temperature in °C,

relative humidity in % RH

7.1 Technical data dew point sensor FA 410

Measuring range -80 to 20 °Ctd

Pressure range -1 to 50 bar standard

Accuracy ±0.5 °Ctd (-10 to 50 °Ctd)

typical ±2 °Ctd at -40 °Ctd

Operation temperature -20 to 70 °C

Storage temperature -40 to 80 °C

Screw-in thread G1/2" stainless steel

3 measured value per

FA 410 Dew point in °Ctd, temperature in °C, relative humidity in

% RH

Please read carefully before starting the device!

1. Attention: Do not exceed pressure range of > 50 bar with standard version.

(Up to 350 bar in case of special version).

2. Important: Before installation briefly bleed the compressed air in order to remove

condensate and particles. This prevents soiling of FA 410. Standing air leads to

long measuring times.

- 9 -

8. Sensor connection

9. Flexible current supply (100… 240 VAC / 50…60 Hz)

In case of fully loaded rechargeable battery (green LED at the right hand side) (approx.

6 hours charging time)

the operation life will be maximum 4 hours without any mains supply. In case of plugged-in

mains supply the rechargeable batteries will be loaded also if the instrument is switched off.

Sensor connections (factory settings):

1Consumption sensor resp. dew point sensor

2Dew point sensor resp. consumption sensor

3Analogue sensor

4Analogue sensor

5Analogue sensor

6Analogue sensor

7Power supply 100-240 VAC

4 5

1 2

3 4

5 6

- 10 -

10. Survey operation menu (with "Enter" one menu level down and return with

"Back")

Table des matières

Manuels Autre populaires d'autres marques

GO Industries

GO Industries 38017 Manuel utilisateur

Cissell

Cissell 30LBCMAN2 Manuel utilisateur

RIDGID

RIDGID K-60SP Manuel utilisateur

Gage Bilt

Gage Bilt GB751SH-5 Manuel utilisateur

OVE

OVE SIERRA 60 Manuel utilisateur

ReelCraft

ReelCraft 7800 OLB21 Manuel utilisateur

Body Armor 4x4

Body Armor 4x4 ECO-SERIES Manuel utilisateur

ROBLIN

ROBLIN DROP Guide de l'utilisateur

EMG

EMG EMG-ACB BARREL Manuel de service

MiniSolar

MiniSolar MT-150 Manuel utilisateur

Parkside

Parkside PSZ 250 B2 Manuel utilisateur

ABB

ABB REM 610 Manuel du produit

Parkside

Parkside 55992 Manuel du propriétaire

Skyjacker

Skyjacker F250 Manuel utilisateur

IBM

IBM IBM SYSTEM Z Guide d'installation

Grech Motors

Grech Motors G28 Manuel utilisateur

NOVAK

NOVAK BATTERY CARE SHEET Mode d’emploi

Telemotive

Telemotive blue PiraT Mini Guide de l'utilisateur