Crystal Vision ADDEC-310 Manuel utilisateur

Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England.

E-mail: [email protected] Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059

ADDEC-310

Analogue to SDI decoding converter

ADDEC-310 User Manual R1.2 Crystal Vision

ADDEC-310 User Manual R1.2 110/12/2007

Contents

1Introduction 3

1.1Operating modes 4

Synchroniser and Delay Modes 4

Analogue video formats 5

Freezing the picture 5

Video Input loss behaviour 5

Status and control 5

2Hardware installation 6

2.1Rear modules and signal I/O 6

Rear module connections with RM01 6

Rear module connections with RM23 7

Rear module connections with RM24 7

Rear module connections with RM25 8

Rear module connections with RM27 8

Module configuration 9

2.2General Purpose Interface (GPI) 10

3Card edge operation 14

3.1Card edge switch settings 14

3.2Card edge rotary controls 14

3.3Reading card edge LEDs 15

3.4Navigating card edge menus 15

3.5Card edge configuration 16

Main menus 16

Status Menus 16

Using presets 17

ADDEC-310 User Manual R1.2 Crystal Vision

ADDEC-310 User Manual R1.2 210/12/2007

Set up menu 17

Video levels and gains 20

Engineering settings 21

4Using the active front panel 23

4.1Module selected 23

The ADDEC-310 menu structure 25

Active control panel menu tree 26

Video Configuration Menu 26

Miscellaneous menu 28

Status menu 29

5Statesman 30

5.1Statesman operation 30

Video properties 31

Presets 33

Gains 34

Factory Reset 35

6Trouble shooting 36

6.1Card edge monitoring 36

Status LEDs 36

6.2Fault finding guide 37

7Specification 38

Revision 1. Page 10. Links PL9 and PL11 information corrected. 06/11/07

Revision 2. Page 10. Links PL4 and PL8 information corrected. 29/11/07

Crystal Vision Introduction

ADDEC-310 User Manual R1.2 310/12/2007

1Introduction

ADDEC-310 is a broadcast decoder. It brings together onto one PCB both the functions

of a 12-bit broadcast decoder and synchroniser/delay module.

The ADDEC-310 will convert PAL/NTSC composite, Y/C or YUV/RGB component

video to SDI using a high quality 12-bit decoder which can deal with any source from

broadcast quality to VHS, and will accept damaged or jittery signals. The data is sampled

at 54 Mbit per second (four times oversampled) allowing the highest quality digital

filtering. It also offers the latest in comb technology, with a five-line comb resulting in

exceptional decoding. Timing, gains and levels are also adjustable.

The on-board video frame synchroniser allows untimed inputs to be timed to the local

syncs. It will sort out any incorrect frame rates plus any delays by taking its timing from

the external analogue reference and will automatically synchronise sources between 0 and

2 fields.

An audio follow pulse is also produced which allows ADDEC-310 to be used with an

external audio delay such as the TAD202

The ADDEC-310 will fully integrate with any other interface or keying product from the

Crystal Vision range. Further flexibility is afforded by the large choice of control options,

which include board edge control, local or remote active control panel and the Statesman

PC Control System.

The main features are as follows:

•12-bit digital decoder

•Suitable for all sources, from broadcast quality to VHS

•High quality digital filtering and 5-line comb

•Frame or line synchroniser or used as a fixed delay times input to local reference

syncs

•Flexible control, including PC software.

•Up to four Serial Digital outputs.

•Internal proc amp

•Audio follow pulse output

•Compact design for high packing density

•Full range of inter-changeable rear connector modules

Crystal Vision Introduction

ADDEC-310 User Manual R1.2 410/12/2007

ADDEC-310 12-bit Synchronising Decoder

The ADDEC-310 is a 100mm x 266mm module that fits in Crystal Vision’s four standard

frame sizes. 24 modules fit in 4U, 12 modules fit in 2U, six in 1U or two in a desktop box.

There are a range of rear connector modules available for the ADDEC-310 which offer

the system builder great flexibility in frame configuration.

1.1 Operating modes

Synchroniser and Delay Modes

There are two modes of operation, Synchronisation and Delay.

In Synchronisation Mode the unit takes its timing from the analogue external reference

and will automatically synchronise sources between zero and two fields. Synchronisation

Mode is ideal for external sources that are not timed to station references such as satellite

or remote contribution feeds.

In Delay Mode, timing is derived only from the analogue input. Typical applications are

where a source passes through a processor such as a DVE, Chroma keyer or standards

converter where the delay can be a few microseconds, multiple lines or up to two fields.

Crystal Vision Introduction

ADDEC-310 User Manual R1.2 510/12/2007

The video delay remains fully adjustable over two complete fields. This allows the output

of the ADDEC-310 in synchronisation mode to be timed into any edit suite irrespective of

the timing of the black and burst reference used.

Audio follow pulse

There is also a positive going external TTL level audio follow video (AFV) pulse output,

the duration of which reflects the current video delay. The AFV output can be used with

external audio delay processors such as the TAD202 if required.

Analogue video formats

The analogue video input can be selected to be composite PAL/NTSC and YC or

525/625-line component YUV/RGB. ADDEC-310 can accept an RGB input with sync

pulses on either all three components or Green alone. There is also an RGB external sync

input should the RGB video not have syncs present. Input standard selection is automatic

and will follow the input video. Data in the VBI (vertical blanking interval) of the

analogue composite input can be blanked or passed. NTSC- J and NTSC-M with or

without 7.5% IRE set up is also selectable when receiving an NTSC format video input.

Betacam input levels are also accepted.

Freezing the picture

The picture can be frozen and the freeze mode can be selected from freeze frame, field 1

and field 2. In situations where there is movement between fields a frame freeze may

show movement judder. To prevent this, a field freeze which works by repeating the same

field will produce a synthetic frame of video without movement judder. However a field

freeze is more likely to show jagged edges on near horizontal lines.

Video Input loss behaviour

The ADDEC-310 output will cut to blue immediately on loss of input video.

Status and control

Status and control of the ADDEC-310 is available using the board edge menu selection

switches and 10-digit display. Full function control and status reporting is also available

from either an active frame front or remote active control panel. PC control is also

available using Crystal Visions Statesman PC controller package.

Crystal Vision Hardware installation

ADDEC-310 User Manual R1.2 610/12/2007

2Hardware installation

The ADDEC-310 single height module uses the RM01, RM23, RM24, RM25 and RM27

rear connectors. The RM25 quad height module will only fit into the 2U and 4U frames,

although the rest will fit into all Crystal Vision rack frames. All modules can be plugged

in and removed while the frame is powered without damage.

2.1 Rear modules and signal I/O

The Indigo 4 4U frame will house up to 24 single height modules with up to three power

supplies. The Indigo 2 2U frames will house up to 12 single height modules and dual

power supplies. The Indigo 1 1U frames will house six single height modules and a single

or dual power supply. The Indigo desk top boxes both have a built-in power supply and

will house up to two single height modules.

Note: For details of fitting rear connectors please refer to the appropriate frame manual

Rear module connections with RM01

The RM01being a single height module will allow maximum packing density with the

maximum number of outputs available.

RM01 rear module connector Description

RM01

•24 ADDEC-310 modules

per Indigo 4 frame

•12 per Indigo 2 frame

•Six per Indigo 1 frame

•2 per Indigo DT

•All frame slots can be

used

BNC I/O assignment

SDI OUT / RGB SYNC Serial digital output / External RGB reference input (link selectable)

SDI OUT Serial digital output

V/R IN / SDI OUT Component V and R input / Serial digital output (link selectable)

Y/G/YCY/CVBS IN Component Y and G, Composite YC-Y and PAL/NTSC input

U/B/YCC IN / SDI OUT Component U and B, Composite YC-C input / Serial digital output (link

selectable)

SYNC IN Composite sync (B & B) input

Crystal Vision Hardware installation

ADDEC-310 User Manual R1.2 710/12/2007

Rear module connections with RM23

The RM23 single height rear module also allows maximum packing density but

substitutes one of the outputs for a loop-through for the external reference input.

RM23 modular rear connector Description

•

RM23

•24 ADDEC-310 modules

per Indigo 4 frame

•12 per Indigo 2 frame

•Six per Indigo 1 frame

•2 per Indigo DT

All frame slots can be used

BNC Function

SYNC IN LOOP Composite sync (B & B) input loop-through (looped on rear module)

SDI OUT Serial digital output

V/R IN / SDI OUT Component V and R input / Serial digital output (link selectable)

Y/G/YCY/CVBS IN Component Y and G, Composite YC-Y and PAL/NTSC input

U/B/YCC IN / SDI OUT Component U and B, Composite YC-C input / Serial digital output (link

selectable)

SYNC IN Composite sync (B & B) input

Rear module connections with RM24

The RM24 is a single height rear module, which although has fewer outputs gives the user

the benefit of a sync and composite input loop-through.

RM24 rear module connector Description

RM24

•24 ADDEC-310 modules

per Indigo 4 frame

•Six per Indigo 2 frame

•Three per Indigo 1 frame

•1 per Indigo DT

•Every other slot can be

used

BNC Function

SYNC IN LOOP Composite sync (B & B) input loop-through (looped on rear module)

SDI OUT Serial digital output

SDI OUT Serial digital output (link to be set to SDI out)

CVBS IN Composite PAL/NTSC input

CVBS IN LOOP Composite PAL/NTSC input loop through. (looped on rear module)

SYNC IN Composite sync (B & B) input

Crystal Vision Hardware installation

ADDEC-310 User Manual R1.2 810/12/2007

Rear module connections with RM25

The RM25 quad height module will only fit the 2U and 4U frames. With this rear module,

cards can be inserted in the top two and bottom slots.

RM25 rear module connector Description

RM25

•18 ADDEC-310 modules

per Indigo 4 frame

•9 per Indigo 2 frame

•Slots 1, 2 &4 of each bay

can be used.

•The Indigo 1 and Indigo

DT will not accept the

RM25 rear module

BNC I/O assignment

SDI OUT Serial digital output

V/R IN / SDI OUT Component V and R input / Serial digital output (link selectable)

Y/G/YCY/CVBS IN Component Y and G, Composite YC-Y and PAL/NTSC input

Y/G/YCY/CVBS IN

LOOP Component Y and G, Composite YC-Y and PAL/NTSC input (looped on

rear module)

U/B/YCC IN / SDI OUT Component U and B, Composite YC-C input / Serial digital output (link

selectable)

SDI OUT / RGB SYNC Serial digital output / External RGB reference input (link selectable)

U/B/YCC IN Component U and B, Composite YC-C input

SYNC IN LOOP Composite sync (B & B) input loop-through (looped on rear module)

SYNC IN Composite sync (B & B) input

Rear module connections with RM27

The RM27 is a dual height rear module. This module also has the benefit of a BNC

connection for the audio follow pulse.

RM27 rear module connector Description

RM27

•12 ADDEC-310 modules

per Indigo 4 frame

•Six per Indigo 2 frame

•Three per Indigo 1 frame

•1 per Indigo DT

•Every other slot can be

used

Crystal Vision Hardware installation

ADDEC-310 User Manual R1.2 910/12/2007

Channel A I/O assignment

TP TTL level positive going Audio follow pulse.

SDI OUT Serial digital output

V/R IN / SDI OUT Component V and R input / serial digital output (link selectable)

RGB SYNC IN External RGB reference input

SYNC Composite sync (B & B) input

SYNC LOOP Composite sync (B & B) input loop-through (looped on rear module)

N/C No user connection

Y/G/YCY/CVBS IN Component Y and G, Composite YC-Y and PAL/NTSC input

Y/G/YCY/CVBS IN

LOOP Component Y and G, Composite YC-Y and PAL/NTSC input (looped on

rear module)

SDI OUT Serial digital output (set PL3 and PL6 to SDI)

U/B/YCC IN Component U and B, Composite YC-C input

SDI OUT Serial digital output (set PL9 SDI)

Module configuration

The ADDEC-310 has eight user selectable jumper links, which configure the Component

U / YC-C / Serial digital output, the Component V / SDI OUT, the RGB / SDI OUT and

the RGB sync input and the external reference input termination impedance.

There are also three preset potentiometers. These are factory set and should not require

any adjustment.

Note: Not all input/output combinations are available with all rear modules.

ADDEC-310 moveable links

V/R / SDI OUT port configuration

The Component V/R / SDI OUT port can be configured by setting the position of link

PL2 & PL5 (to be found just above the middle right hand edge of the module). When a

component input is required set jumper link PL2 & PL5 to their upper position. Set

jumper PL2 & PL5 to their lower position when a further SDI output is required.

Note: Links PL2 & PL5 must be moved together as a pair.

Table des matières

Autres manuels Crystal Vision Convertisseur de média

Crystal Vision

Crystal Vision Vision 3 Manuel utilisateur

Crystal Vision

Crystal Vision Up-and-down-AAFD Manuel utilisateur

Crystal Vision

Crystal Vision DEC103S Manuel utilisateur

Crystal Vision

Crystal Vision Q-Down-A-AFD Manuel utilisateur

Crystal Vision

Crystal Vision ShARC-XP Manuel utilisateur

Crystal Vision

Crystal Vision DEC104S Manuel utilisateur

Crystal Vision

Crystal Vision ARC102 Manuel utilisateur

Crystal Vision

Crystal Vision ADDEC-100 Manuel utilisateur

Crystal Vision

Crystal Vision UP-DOWN-VF Series Manuel utilisateur

Crystal Vision

Crystal Vision DEC105S Manuel utilisateur

Crystal Vision

Crystal Vision Indigo ALLDAC Manuel utilisateur

Crystal Vision

Crystal Vision ENC116 Manuel utilisateur

Crystal Vision

Crystal Vision DEC101S Manuel utilisateur

Crystal Vision

Crystal Vision ADDEC-200 Manuel utilisateur

Crystal Vision

Crystal Vision Indigo Wallbox Q-Down Manuel utilisateur

Crystal Vision

Crystal Vision Indigo Q-Down Mini Manuel utilisateur

Crystal Vision

Crystal Vision Indigo ADCA412 Manuel utilisateur

Crystal Vision

Crystal Vision DDAA246 Manuel utilisateur

Crystal Vision

Crystal Vision DEC102S Manuel utilisateur

Crystal Vision

Crystal Vision DDAA132P Manuel utilisateur

Crystal Vision

Crystal Vision Indigo DACA214 Manuel utilisateur

Crystal Vision

Crystal Vision Indigo ADDEC-210 Manuel utilisateur

Crystal Vision

Crystal Vision Up-and-down Manuel utilisateur

Crystal Vision

Crystal Vision DDAA132 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur