Crestron BB-12L Manuel utilisateur
Crestron BB-12L
Wall Mount Back Box
Installation Guide
This document was prepared and written by the Technical Documentation department at:
Crestron Electronics, Inc.
15 Volvo Drive
Rockleigh, NJ 07647
1-888-CRESTRON
All brand names, product names and trademarks are the property of their respective owners.
©2005 Crestron Electronics, Inc.
Crestron BB-12L Wall Mount Back Box
Contents
Wall Mount Back Box: BB-12L 1
Description.................................................................................................................................1
Installation .................................................................................................................................3
Assembly.....................................................................................................................3
Mounting .....................................................................................................................4
Other Mounting Option Accessories ...........................................................................6
Further Inquiries ........................................................................................................................6
Future Updates........................................................................................................................... 6
Return and Warranty Policies ....................................................................................................7
Merchandise Returns / Repair Service ........................................................................ 7
CRESTRON Limited Warranty...................................................................................7
Installation Guide - DOC. 6357A Contents •i
Crestron BB-12L Wall Mount Back Box
Wall Mount Back Box: BB-12L
Description
The BB-12L is a UL®-listed pre-construction mounting option for the Crestron Isys®
TPS-12L and TPS-12G-L wall mounted touchpanels. The table below lists all of the
parts included with the BB-12L.
Supplied Components
DESCRIPTION PART NUMBER QUANTITY
Wall Mount Enclosure Assembly 4500077 1
Mounting Bracket 2004218 2
Cover Plate 2012966 1
Screw, 06-32, 1/4” L, pan phillips 2007213 4
Screw, 08-8B, 1/4” L, pan phillips, self-tapping 2007277 1
Screw, 06-32, 1 1/2" L, pan phillips 2007254 8
The mounted view of the BB-12L is shown in the following diagram.
BB-12L Mounted View (Optional Cover Plate Attached)
HOLES FOR STANDARD DRYWALL SCREWS
OR NAILS TO MOUNT TO STUD.
ALTERNATE HOLES LOCATED INSIDE BACK BOX
Installation Guide - DOC. 6357A Wall Mount Back Box: BB-12L •1
Wall Mount Back Box Crestron BB-12L
The dimensions of the BB-12L are shown in the following diagram.
Dimensional Drawing (Fully Assembled without Cover Plate)
3.31 in
(8.41 cm)
3.06 in
(7.77 cm)
12.78 in
(32.45 cm)
12.17 in
(30.92 cm)
0.03 in
(0.08 cm)
11.55 in
(29.34 cm)
13.28 in
(33.72 cm)
COVER PLATE
13.75 in
(34.92 cm)
10.87 in
(27.61 cm)
BACK BOX (ASSEMBLED)
14.65 in
(37.21 cm)
2 •Wall Mount Back Box: BB-12L Installation Guide - DOC. 6357A
Crestron BB-12L Wall Mount Back Box
Installation
Assembly
Required Tools:
• #2 Phillips tip screwdriver
Complete the following assembly procedure in the order provided (refer to
illustration below).
1. Remove knockouts as required.
2. Attach the supplied #08-8B self-tapping screw to the enclosure assembly
for grounding.
3. Attach upper and lower mounting brackets to the enclosure assembly using
supplied (4) #6-32 x 1/4” screws.
Assembly View
#6-32 X 14"L PAN HEAD SCREW (2007213)
QTY. 4 TOTAL
(2007277) FOR GROUND PURPOSES
#08-8B 1/4"L SELF TAPPING SCREW
TOUCHPANEL QTY. 1
ENCLOSURE ASSEMBLY (4500077) FOR
MOUNTING BRACKETS, (2004218) QTY. 2
Installation Guide - DOC. 6357A Wall Mount Back Box: BB-12L •3
Wall Mount Back Box Crestron BB-12L
Mounting
Required Tools:
• #2 Phillips tip screwdriver or hammer
• Level
Complete the following procedure (refer to illustration below) to mount the back
box.
1. Position the back box to the front edge of the stud and align it as even and
as flush as possible.
2. Use the level and verify that the back box is horizontal. Leveling must be
done before proceeding.
3. Attach the back box to right side of the stud with standard drywall screws or
nails (supplied by other). If the mounting brackets cannot be used due to the
back box location (i.e. above/below a crossbeam), remove the brackets and
attach the back box to the left or right side of stud using the holes on the
side of the back box.
NOTE: The back box can be mounted to the left side of the stud by
rotating the back box so the mounting brackets and/or mounting holes are
on the right.
4. Feed cables through knockout holes.
NOTE: This back box should use Class 2 wiring only.
Mounted View with Cover Plate (Mounting Example - Drywall Not Shown)
MOUNTING BACK BOX
FLUSH AS POSSIBLE WHEN
SURFACES BE AS EVEN AND
IT IS IMPORTANT THAT THESE
(2007254) QTY. 8
PAN HEAD SCREW
SCREW, #6-32, 1-1/2"L
AS LEVEL AS POSSIBLE
MOUNTED TO THE STUD
BACK BOX MUST BE
(IF REQUIRED BY LOCAL BUILDING CODES)
IF TOUCHPANEL IS NOT INSTALLED
USE TO COVER CUTOUT IN THE DRYWALL
METAL COVER PLATE (2012966 SUPPLIED)
ALTERNATE
MOUNTING
HOLES
4 •Wall Mount Back Box: BB-12L Installation Guide - DOC. 6357A
Crestron BB-12L Wall Mount Back Box
Refer to the following illustration for cutout dimensions.
Drywall Cutout Dimensions
CAUTION: A 12-inch (minimum) air gap above and below the touchpanel is
required when positioning the BB-12L.
NOTE: Confirm that the eight tapped holes on the front of the back box are exposed
to accept the touchpanel mounting screws.
NOTE: Cut the drywall to the inside edge of the front of the back box and notch
where needed for the screwholes.
5. Complete the installation by either installing the touchpanel, leaving
the hole open (if permitted by local building codes), or installing the
supplied cover plate with the included #6-32 x 1½” screws. If the
touchpanel is to be installed, refer to the latest revision of the
TPS-12L/15L/17L Operations Guide (Doc. 6355) or TPS-12G/15G-L
Operations Guide (Doc. 6356) for installation instructions.
Installation Guide - DOC. 6357A Wall Mount Back Box: BB-12L •5
Wall Mount Back Box Crestron BB-12L
Other Mounting Option Accessories
If too much of the front of the back box is exposed after the drywall is cut, you may
need to patch the area. Crestron offers the following accessories:
• MMK-12L (Doc. 6359) - for larger repairs and to fill in larger irregularities
around the opening (requires plastering).
• TMK-12L (Doc. 6360) - for smaller repairs and to provide a smooth edge at
the opening. This option provides a finished appearance and is preferred
when wallpaper is hung.
The manuals for the MMK-12L and TMK-12L are available for review from the
Crestron website (http://www.crestron.com/manuals).
Further Inquiries
If you cannot locate specific information or have questions after reviewing this
guide, please take advantage of Crestron's award winning customer service team by
calling the Crestron corporate headquarters at 1-888-CRESTRON [1-888-273-7876].
For assistance in your local time zone, refer to the Crestron website
(www.crestron.com) for a listing of Crestron worldwide offices.
You can also log onto the online help section of the Crestron website to ask
questions about Crestron products. First-time users will need to establish a user
account to fully benefit from all available features.
This product is Listed to applicable UL Standards and requirements by Underwriters
Laboratories Inc.
(E227280)
As of the date of manufacture, the BB-12L has been tested and found to comply with
specifications for CE marking.
Future Updates
As Crestron adds improvements to the BB-12L, additional information may be made
available as manual updates. These updates are solely electronic and serve as
intermediary supplements prior to the release of a complete technical documentation
revision.
Check the Crestron website periodically for manual update availability and its
relevance. Updates are identified as an “Addendum” in the Download column.
6 •Wall Mount Back Box: BB-12L Installation Guide - DOC. 6357A
Table des matières
Autres manuels Crestron Enceinte
Crestron
Crestron MPB3-TTK-SQR Manuel utilisateur
Crestron
Crestron BB-4L Manuel utilisateur
Crestron
Crestron C2N-DEMO-INTERFACE Manuel utilisateur
Crestron
Crestron BB-3100L Manuel utilisateur
Crestron
Crestron BB-4L Manuel utilisateur
Crestron
Crestron C2N-DEMO-LIGHTING Manuel utilisateur
Crestron
Crestron BB-1700CW Manuel utilisateur
Crestron
Crestron ZUMMESH-JBOX-FMKT-CP Manuel utilisateur
Crestron
Crestron BB-2000L Manuel utilisateur
Crestron
Crestron CAEN Manuel utilisateur
Crestron
Crestron BB-1600 Manuel utilisateur
Crestron
Crestron BB-17L Manuel utilisateur
Crestron
Crestron TSW-770-FP Manuel utilisateur
Crestron
Crestron BB-3000L Manuel utilisateur
Crestron
Crestron Automation Enclosures CAEN Series Manuel utilisateur
Crestron
Crestron BB-6000 Manuel utilisateur
Crestron
Crestron BB-4000L Manuel utilisateur
Crestron
Crestron BB-5000 Manuel utilisateur
Crestron
Crestron BB-15L Manuel utilisateur
Crestron
Crestron CAGE3 Manuel utilisateur
