Cree TDS Series Manuel utilisateur

TDS Series

LED DISK LIGHT

Includes: TDS4, and TDS6

INSTALLATION INSTRUCTIONS

1 of 2 LPN000245_A

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always be followed

including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

2. This luminaire must be installed in accordance with the NEC or your local

electrical code. If you are not familiar with these codes and requirements,

consult a qualied electrician.

3. WARNING: Not intended for use with emergency exit xtures or emergency exit

lights. Not for use where exposed directly to the weather or water. Not for use in

totally enclosed recessed xtures

4. WARNING: Risk of Fire or Electric Shock. Install this product only in the

applications that have the construction features and dimensions shown in the

photographs and/or drawings.

5. DO NOT make or alter any open holes in an enclosure of wiring or electrical

components during kit installation.

6. To prevent wiring damage or abrasion, do not expose wiring to edges of sheet

metal or other sharp objects.

7. WARNING: Risk of Fire or Electric Shock. Install this kit only in luminaires where

the input ratings of the kit does not exceed the input ratings of the luminaire.

8. CAUTION: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

9. CAUTION: Risk of electrical shock. Do not open. There are no user serviceable

parts inside. Turn the power on before inspection, installation, or removal. The

lamp is suitable for use in wet locations. Use only on 120 VAC, 60 Hz circuits.

10. IMPORTANT: Each light shall be installed only in its intended manner and

orientation. Not all existing recessed cans that meet these requirements will be

compatible with the Cree Disk Light.

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE

PRE-INSTALLATION

This 6 in. or 4 in. disk light can be used in general lighting for residential and commercial spaces in ceiling lighting. The LED retrofit is designed to install

in either a standard 6 in. or 4 in. recessed can, or surface mounted onto a 4 in. junction box.

To prepare for a junction box installation, refer to the chart below to determine if the disk light mounting bracket is required.

Junction Box Type 4 in. Light 6 in. Light

Square Install bracket Install bracket

Octagonal Install bracket Bracket not required

Round Bracket not required Bracket not required

COMPATIBILITY

RECESSED HOUSING AND DIMMER COMPATIBILITY

• The Cree LED Disk Light is designed to install in either a standard 6" or 4" recessed can or surface mounted onto a 4" junction box.

• Compatible with most dimmers when used with multiple fixtures. Consult www.creebulb.com/dimmers for a compatibility chart.

ELECTRICAL RATINGS

Model Input Volts (Vac) Input Frequency (Hz) Input Watts (W)

TDS4-0602700FH50-12DDWRE-1-11 120 60 9

TDS6-0652700FH50-12DDWRE-1-11 120 60 10.5

110°

PACKAGE CONTENTS

1- 6 in. or 4 in. disk

light

1- Edison socket

adapter

1- Base wire adapter

1- Flip-clip mount

3- Wire nut

1- Lens removal tool

1- Disk light mounting

bracket

2- 8-18 x ½ in. Thread

forming screw

2- 8-32 x 1 in.

Machine screw

1- Ground clip

2 of 2 LPN000245_A

RECESSED CAN INSTALLATION

STEP 1:

Remove the lens from the disk light with

the lens removal tool , by working the tool

around the opening. See Figure 1.

STEP 2:

Firmly attach the flip-clip mount to the

disk light by aligning the grooves in the

disk light with the flip-clip mount and

attach with the two 8-18 x 1/2" thread

forming screws. See Figure 2.

STEP 3:

Reattach the lens to the disk light by

snapping it back into place. See Figure 2.

STEP 4:

Attaching the socket adapter by reaching

inside the existing recessed can, and

screw the Edison socket adapter into the

female Edison socket. See Figure 3.

STEP 5:

Insert the bare end of the grounding

wire coming off of the disk light into the

ground clip and attach to the edge of the

recessed can. See Figure 4.

STEP 6:

Connecting the light to the socket

adapter. Connect the orange female

connector from the disk light to the

orange male connector that extends

from the end of the Edison socket

adapter. See Figure 5.

STEP 7:

Install the light into the ceiling by

rotating the flip clips on the mount

clockwise until the clips are oriented

directly away form the fixture. This

position is the “installation ready”

position. See Figure 6.

STEP 8:

Slide the disk light, with the flip-clips in

fully-deployed position, up into the

recessed can firmly until the trim ring

on the disk light is flush with the ceiling.

See Figure 6.

JUNCTION BOX INSTALLATION

STEP 1:

If required, according to the chart in the

Planning Installation section, install

the disk light mounting bracket onto

the junction box with the two 8-32 x 1"

machine screws. See Figure 7.

STEP 2:

On the junction box, you will need to make

two pigtail connections. Connect the

black junction box wire (hot wire) to the

black pigtail wire of the base wire adapter

using one of the provided wire nuts. See

Figure 8.

STEP 3:

Connect the white junction box wire

(neutral wire) to the white pigtail wire of

the bare wire adapter using one of the

provided wire nuts. See Figure 8.

6" or 4 " Disk

Light

Lens

Lens Removal Tool

Flip-Clip Mount

6" or 4 " Disk

Light

Lens

8-18 x ½"

Thread Forming

Screw

Edison Socket Adapter

Ground Clip

6" or 4 "

Disk Light

Edison Socket

Adapter

6" or 4 " Disk

Light

6" or 4 "

Disk Light

Flip-Clip

Mount

Disk Light

Mounting

Bracket

Wire Nut

Base Wire

Adapter

8-18 x ½" `Thread Forming Screw

3 of 2 LPN000245_A

www.creebulb.com

See creebulb.com/warranty for warranty and specifications. Cree® is a registered trademark, and the Cree logo is a trademark

of Cree, Inc.

FCC NOTICE

CAUTION: Changes or modications not expressly approved could void your authority to use this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modications not expressly approved could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

CAN ICES-005 (B)/NMB-005 (B)

In compliance with CA Proposition 65, note that this product contains a chemical known to the state of California to cause cancer, birth defects or other

reproductive harm.

WARRANTY

100% SATISFACTION GUARANTEE: This product is guaranteed to give 100% performance satisfaction subject to the Cree limited warranty, the terms

of which can be found at creebulb.com/warranty. If within 10 years from the date of purchase you are not completely satised with the performance of

this product, please contact Cree for replacement instructions.

Wire Nut

Base Wire

Adapter

6" or 4 " Disk

Light

Disk Light

Mounting

Bracket

6" or 4 " Disk

Light

8-18 x 1"

Machine Screw

STEP 4:

Connect the ground wire from the disk light to the ground wire in the junction

box using one of the provided wire nuts.

Connect the orange female connector from the disk light to the orange male

connector that extends from the base wire adapter. See Figure 9.

STEP 5:

Remove the lens from the light by detaching the lens with the lens removal tool.

See Figure 1.

STEP 6:

Using the two 8-18 x 1/2" thread forming screws, attach the disk light to the

junction box or to the mounting bracket if you installed one. Ensure the trim

ring on the light is flush with the ceiling. See Figure 10.

STEP 7:

Reattach the lens to the disk light by snapping it back into place.

MAINTENANCE

REMOVING THE LED DISK LIGHT FROM A RECESSED CAN

STEP 1:

Grip firmly on the trim ring and rotate 1/4 turn counterclockwise to unlock the

clips from the recessed can.

STEP 2:

Continue to turn counterclockwise as you pull downward on the disk light. This

will disengage the flip-clips allowing the disk light (A) to pull free.

STEP 3:

Detach the disk light from the recessed can socket.

Ce manuel convient aux modèles suivants

Autres manuels Cree Équipement d'éclairage

Cree

Cree LS8 Manuel utilisateur

Cree

Cree Link With SmartCast Technology Manuel utilisateur

Cree

Cree FLEX Series Manuel utilisateur

Cree

Cree XLamp ML Family LEDs Manuel utilisateur

Cree

Cree OSQ Series Manuel utilisateur

Cree

Cree EB14SMK Manuel utilisateur

Cree

Cree LR24 Series Manuel utilisateur

Cree

Cree CPY Series Manuel utilisateur

Cree

Cree CR150-650L Manuel utilisateur

Cree

Cree XLamp MH Series Manuel utilisateur

Cree

Cree OSQ Series Manuel utilisateur

Cree

Cree TRDL6 Series Manuel utilisateur

Cree

Cree CXB Series Manuel utilisateur

Cree

Cree OSQ Series Manuel utilisateur

Cree

Cree ESSENTIA ESA-ADR-414 Manuel utilisateur

Cree

Cree OSQ HO Series Manuel utilisateur

Cree

Cree ESSENTIA AE Series Manuel utilisateur

Cree

Cree OSQ Series Manuel utilisateur

Cree

Cree XA-NEMA Manuel utilisateur

Cree

Cree CR24 UPKIT Manuel utilisateur

Cree

Cree OSQ Series Manuel utilisateur

Cree

Cree CR Series Manuel utilisateur

Cree

Cree ZR Series Manuel utilisateur

Cree

Cree LXB Series Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur