Craftsman ASF 486.246213 Manuel utilisateur

TRACTOR BRUSH GUARD

Model No's. 486.246213, 486.246222 & 486.246232

Owner's Manual

CAUTION:

Before using this product, read

this manual and follow all Safety

Rules and Operating Instructions.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

PRINTED IN U.S.A. FORM NO. 40865 rev. (04/24/08)

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

www.sears.com/craftsman

STOP

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

2Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

Any power equipment can cause injury if operated

improperly or if the user does not understand how to

operate the equipment. Exercise caution at all times,

when using power equipment.

• Refer to your tractor owners manual for "Rules For

Safe Operation".

• Bumper may get hot when tractor is running! Allow

bumper to cool down before grabbing hold of bumper.

Look for this symbol to point out important safety

precautions. It means — Attention!! Become

alert!! Your safety is involved.

ONE YEAR LIMITED WARRANTY

When operated and maintained according to the instructions

supplied with it, if this Tractor Brush Guard fails due to a defect

in material or workmanship within one year from the date of

purchase, call 1-800-4-MY-HOME®to arrange for free repair.

If this product is used for commercial or rental purposes, this

warranty applies for only 90 days from the date of purchase.

This warranty gives you specic legal rights, and you may also

have other rights which vary from state to state.

Sears, Roebuck and Co., D817WA, Hoffman Estates, IL

60179

WARRANTY SAFETY

BEFORE YOU BEGIN

DETERMINE IF YOUR TRACTOR HAS A SINGLE SUSPENSION BRACKET

OR DUAL SUSPENSION BRACKETS

Look under the front of your tractor (Figure 1A & 1B). If there is a single mower deck suspension bracket located underneath

the middle of the front axle, continue on to INSTRUCTIONS FOR SINGLE SUSPENSION BRACKET TRACTORS on

page 3. If your tractor does not have a mower deck suspension bracket underneath the middle of the front axle, skip to

INSTRUCTIONS FOR DUAL SUSPENSION BRACKET TRACTORS on page 5.

FIGURE 1B (page 5)

FIGURE 1A (page 3)

SUSPENSION

BRACKET

TOOLS REQUIRED

(2) 9/16" Wrenches

(1) 1/2" Wrench (for heat shield on page 5)

CARTON CONTENTS

REF PART NO. QTY. DESCRIPTION

1 25038 1 Right Mounting Bracket

2 25037 1 Left Mounting Bracket

3 64862 2 Locking Lever

4 64614B 1 Bumper (71-246213)

64614S 1 Bumper (71-246222)

64614C 1 Bumper (71-246232)

SUSPENSION BRACKET

SUSPENSION

BRACKET

SINGLE SUSPENSION

BRACKET

DUAL SUSPENSION BRACKETS

Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

INSTRUCTIONS FOR SINGLE SUSPENSION BRACKET TRACTORS

REF PART NO. QTY. DESCRIPTION

A 43350 2 Carriage Bolt, 3/8-16 x 1"

B43062 2 Hex Bolt, 3/8-16 x 1-1/2"

C 44072 4 Whizlock Nut, 3/8"

D 44742 4 Plug

E 48866 2 Pivot Spacer

F1643-60 2 Plastic Grip

NOTE: Place cardboard or a mat on work surface to prevent

scratching of parts removed from carton and tractor.

STEP 1: (SEE FIGURE 2)

Open parts bag labelled "A" and verify that all parts are

present.

STEP 2: (SEE FIGURE 3)

• Remove hood from tractor using instructions in your

tractor owner's manual. Place hood on cardboard or

on a mat to protect paint.

• Remove the browning shield from the front of the

tractor as shown.

IMPORTANT: Be sure to reattach the browning shield

after bumper is installed.

REMOVE

BROWNING SHIELD

REMOVE

FRONT SCREWS

FIGURE 3

SHOWN FULL SIZE

PARTS BAG "A"

NOT SHOWN

FULL SIZE

FIGURE 2

CAUTION! Mufer is hot! Allow engine to

cool down before proceeding with bumper

installation.

NOTE: Right hand (RH) and left hand (LH) are

determined from the operator's position while seated on

the tractor.

4Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

STEP 3: (SEE FIGURE 4)

• Place plug (D) on a work bench or solid table and

push end of bumper down onto plug. Repeat for all

four plugs.

FIGURE 4

PLUG (D)

BUMPER

PUSH DOWN

WITH EVEN

PRESSURE

WORK BENCH

OR SOLID TABLE

STEP 4: (SEE FIGURE 5)

• Attach left mounting bracket to hole shown in left side

of tractor frame using a carriage bolt (A) and whizlock

nut (C). Align middle hole in bracket with empty hole

in tractor frame. Tighten whizlock nut (C) only enough

to keep bracket in alignment until step 5. Repeat for

right mounting bracket.

WHIZLOCK

NUT (C)

LEFT MOUNTING

BRACKET

BUMPER STOPS

FACE OUT

ALIGN THESE HOLES

CARRIAGE

BOLT (A)

LEFT SIDE VIEW FIGURE 5

(GT) FRAME SHOWN

STEP 5: (SEE FIGURE 6)

• Fasten bumper to mounting bracket using a hex bolt

(B), pivot spacer (E), a locking lever and a whizlock

nut (C) as shown. The pivot spacer inserts into hole in

bumper. Tighten both nuts on mounting bracket at

this time. Repeat for other side.

• Assemble plastic grips (F) onto locking levers.

• Lift up on bumper until pins in locking levers snap into

holes in mounting brackets.

IMPORTANT: You must lower bumper before raising tractor

hood. Pull out on locking levers and push bumper down as

far as it will go.

FIGURE 6 LEFT SIDE VIEW

PIVOT

SPACER (E)

HEX BOLT (B)

LOCKING

LEVER

GRIP (F)

WHIZLOCK

NUT (C)

STEP 6: (SEE FIGURE 7)

• Replace the front screws and browning shield you

removed in Step 2 as shown.

FIGURE 7 LEFT SIDE VIEW

REPLACE

BROWNING SHIELD

REPLACE

FRONT SCREWS

CAUTION! Bumper may get hot when

tractor is running! Allow bumper to cool

down before grabbing hold of bumper.

Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

REF PART NO. QTY. DESCRIPTION

A 48894 2 Self Threading Screw, 3/8-16 x 1-1/2"

B43062 2 Hex Bolt, 3/8-16 x 1-1/2"

C 43001 2 Hex Bolt, 3/8-16 x 1"

D 48866 2 Pivot Spacer

E 1643-60 2 Plastic Grip

F43003 4 Lock Washer, 3/8"

G 43070 4 Washer, 3/8"

H 44742 4 Plug

NOTE: Place cardboard or a mat on work surface to prevent

scratching of parts removed from carton and tractor.

STEP 1: (SEE FIGURE 2)

Open parts bags labelled "A" and "B" and verify that all

parts are present.

CAUTION! Mufer is hot! Allow engine to

cool down before proceeding with bumper

installation.

NOTE: Right hand (RH) and left hand (LH) are

determined from the operator's position while seated on

the tractor.

INSTRUCTIONS FOR DUAL SUSPENSION BRACKET TRACTORS

STEP 2: (SEE FIGURE 3)

• Remove tractor hood. (Refer to tractor manual.) Place

hood on cardboard or on a mat to protect paint.

• If you have an (LT) Lawn Tractor with a heat shield

like the one shown, remove the heat shield.

IMPORTANT: Be sure to re-attach the heat shield after

bumper is installed.

FIGURE 3

SHOWN FULL SIZE

PARTS BAG "B" EXCEPT WHERE NOTED

(parts bag "A")

FIGURE 2

MUFFLER HEAT SHIELD

(LT) LAWN TRACTOR

6Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

SUSPENSION BRACKET

REMOVE BOLT

IF PRESENT

REMOVE BOLT

IF PRESENT

SUSPENSION BRACKET

(LT) LAWN TRACTOR

(GT) GARDEN TRACTOR

SUSPENSION

BRACKET

REMOVE BOLT

IF PRESENT

(LT) LAWN TRACTOR

STEP 4: (SEE FIGURE 5)

IMPORTANT: Do not remove any bolts from the tractor

frame while the mower deck is raised. Misalignment of

holes in frame could result.

• Lower mower deck to rest on ground.

• Remove bolts from mounting holes on both sides of

tractor frame. Use a mounting bracket to help identify

holes.

STEP 3: (SEE FIGURE 4)

• Place plug (H) on a work bench or solid table and

push end of bumper down onto plug. Repeat for all

four plugs.

PLUG (H)

BUMPER

PUSH DOWN

WITH EVEN

PRESSURE

WORK BENCH

OR SOLID TABLE

FIGURE 4

FIGURE 5

Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

STEP 6: (SEE FIGURES 7 & 8)

• Assemble plastic grips (E) onto locking levers.

• To attach bumper to tractor:

1. Place attened ends of bumper onto mounting

brackets. Insert pin of locking lever through front

hole in bumper and into front hole in mounting

bracket to support bumper on mounting bracket.

2. Insert pivot spacers (D) into rear holes in bumper.

PIVOT

SPACER

(D)

LOCKING LEVER

GRIP (E)

3. Fasten locking lever and bumper to mounting bracket

using a screw (A) or bolt (B), a lock washer (F) and a

at washer (G). Use screw (A) for LT tractors and bolt

(B) for GT tractors. Assemble screw or bolt through

pivot spacer in rear hole in bumper and into tractor

frame. Tighten. Repeat for other side.

NOTE: If hole in (LT) tractor frame is not threaded, push

in while turning screw (A) to create threads in hole.

IMPORTANT: You must lower bumper before raising tractor

hood. Pull out on locking levers and push bumper down as

far as it will go.

FLAT

WASHER (G)

LOCK

WASHER (F)

SCREW (A)

or BOLT (B)

STEP 5: (SEE FIGURE 6)

• Attach left mounting bracket to hole shown in left

side of tractor frame using bolt (C), lock washer (F)

and at washer (G). Align middle hole in bracket

with empty hole in tractor frame and tighten bolt (C)

to hold bracket in place. Repeat for right mounting

bracket.

FLAT

WASHER

(G)

LOCK

WASHER

(F)

BOLT

(C)

LEFT MOUNTING

BRACKET

BUMPER STOPS

FACE OUT

ALIGN THESE HOLES

ATTACH TO

THIS HOLE

LEFT SIDE VIEW FIGURE 6

LEFT SIDE VIEW FIGURE 7

LEFT SIDE VIEW FIGURE 8

(GT) FRAME SHOWN

CAUTION! Bumper may get hot when

tractor is running! Allow bumper to cool

down before grabbing hold of bumper.

® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC

® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC

MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC

Get it fixed, at your home or ours!

Your Home

For repair – in your home – of all major brand appliances,

lawn and garden equipment, or heating and cooling systems,

no matter who made it, no matter who sold it!

For the replacement parts, accessories and

owner’s manuals that you need to do-it-yourself.

For Sears professional installation of home appliances

and items like garage door openers and water heaters.

1-800-4-MY-HOME®(1-800-469-4663)

Call anytime, day or night (U.S.A. and Canada)

www.sears.com www.sears.ca

For expert home solutions advice: www.managemyhome.com

Our Home

For repair of carry-in items like vacuums, lawn equipment,

and electronics, call or go on-line for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (U.S.A.) 1-800-469-4663 (Canada)

Call anytime, day or night

www.sears.com www.sears.ca

To purchase a protection agreement on a product serviced by Sears:

1-800-827-6655 (U.S.A.) 1-800-361-6665 (Canada)

Para pedir servicio de reparación

a domicilio, y para ordenar piezas:

1-888-SU-HOGAR®

(1-888-784-6427)

Au Canada pour service en français:

1-800-LE-FOYERMC

(1-800-533-6937)

www.sears.ca

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Craftsman Accessoires

Craftsman

Craftsman 358.792443 Manuel utilisateur

Craftsman

Craftsman 358.792450 Manuel utilisateur

Craftsman

Craftsman Door Kit Manuel utilisateur

Craftsman

Craftsman 486.246212 Manuel utilisateur

Craftsman

Craftsman 390.2519 Manuel utilisateur

Craftsman

Craftsman 486.24611 Manuel utilisateur

Craftsman

Craftsman CMXZDCG480 Manuel utilisateur

Craftsman

Craftsman 875.59750 Manuel utilisateur

Craftsman

Craftsman 486.24831 Manuel utilisateur

Craftsman

Craftsman 944.511591 Manuel utilisateur

Craftsman

Craftsman 486.24218 Manuel utilisateur

Craftsman

Craftsman 486.24100 Manuel utilisateur

Craftsman

Craftsman 139.53724 Manuel utilisateur

Craftsman

Craftsman ASF 486.246213 Manuel utilisateur

Craftsman

Craftsman 572.530331 Manuel utilisateur

Craftsman

Craftsman 316.792420 Manuel utilisateur

Craftsman

Craftsman 320.16495 Manuel utilisateur

Craftsman

Craftsman 113.29931 Manuel utilisateur

Craftsman

Craftsman 139.53784 Manuel utilisateur

Craftsman

Craftsman 240.74291 Manuel utilisateur

Craftsman

Craftsman 351.264271 Manuel utilisateur

Craftsman

Craftsman 358.792421 Manuel utilisateur

Craftsman

Craftsman 944.511573 Manuel utilisateur

Craftsman

Craftsman 351.240870 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur