Craftsman 486.24611 Manuel utilisateur

Owner's IVlanuai

FRONT U E

IVlodel Nos. 486.24611,486.24612

Fits 247 and 917 Series LT/GT Tractors

DO NOT RETURN TO STORE

For Missing Parts or Assembly

Questions Call 1-866-576-8388

CAUTION:

Before using this product, read this

manual and follow all Safety Rules

and Operating Instructions.

,, Safety

,, Assembly

,, Operation

,, Maintenance

,, Parts

Sears Brands Management Corporation, Hoffman Estates, IL 60179 U.S.A.

www.craftsman.com

PRINTED iN U.S.A. FORM NO. 41334 (12/09109)

WARRANTY

CRAFTSMAN ONE-YEAR FULL WARRANTY

When assembled, operated and maintained according to

the supplied instructions, if this product fails due to a defect

in material or workmanship within one year from the date of

purchase, return it to any Sears store or other Craftsman outlet

in the United States for free replacement.

This warranty is void if this product is ever used for commercial

or rental purposes.

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

Sears, Roebuck and Co., Hoffman Estates, IL 60179

SAFETY

Any power equipment can cause injury ifoperated improperly

or if the user does not understand how to operate the

equipment. Exercise caution at all times when using power

equipment.

*Refer to your tractor owners manual for "Rules For

Safe Operation".

Look for this symbol to point out important safety

precautions. It means -- Attention!! Become

alert!! Your safety is involved.

BEFORE YOU BEGIN

TOOLS REQUIRED

(2) 9/16" Wrenches (Socket wrench may be used)

(2) 1/2" Wrenches (Socket wrench may be used)

(2) Adjustable wrenches

CAUTION!

cool down

installation.

Muffler is hot! Allow engine to

before proceeding with bumper

LOCATE YOUR TRACTOR MODEL NUMBER

Look under the seat of your tractor and locate the model number. For tractors with model numbers beginning with 917,

proceed to DETERMINE IFYOUR TRACTOR HAS A SINGLE SUSPENSION BRACKET OR DUAL SUSPENSION

BRACKETS on page 3. For tractors with model numbers beginning with 247, proceed to IDENTIFYYOUR TRACTOR

FRAME on page 8.

CRnFTZMI:IM

CONFORMS TO ANSi B71.1=2003 SAFETY STANDARDS

III |11 '"'"" IIIII1|1|

IIIII ...,

SERIAL 000000A000000

FOR PARTS AND SERVICE CALL 1-800-4MY-HOME

SEARS, ROEBUCK AND CO., Hoffmarl Estates, IL 60179 193653 .J

CRnFTXMI;IN

CONFORMS TO ANSi B71.1=2003 SAFETY STANDARDS

III|11 '"'""" IIIII|1|

IIIII "'"" IIIIIII1|11

SERIAL 000000A000000

FOR PARTS AND SERVICE CALL 1-800-4MY-HOME

SEARS, ROEBUCK AND CO., }4orrman Estates, IL 60179 193653

917 MODEL TRACTORS

GO TO PAGE 3 247 MODEL TRACTORS

GO TO PAGE 8

2 Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

DETERMINE IFYOUR TRACTOR HAS A SINGLE SUSPENSION BRACKET "_

OR DUAL SUSPENSION BRACKETS J

SINGLE SUSPENSION

BRACKET

SUSPENSION

BRACKET

FIGURE 1A (page 3)

DUAL SUSPENSION BRACKETS

SUSPENSION BRACKET SUSPENSION

BRACKET

FIGURE 1B (page 5)

For all tractors with model numbers beginning with 917, look under the front of your tractor (Figure 1A & 1B). If there is a

single mower deck suspension bracket located underneath the middle of the front axle, continue on to INSTRUCTIONS

FOR SINGLE SUSPENSION BRACKET TRACTORS on page 3. Ifyour tractor does not have a mower deck suspension

bracket underneath the middle of the front axle, skip to INSTRUCTIONS FOR DUAL SUSPENSION BRACKET

TRACTORS on page 5.

INSTRUCTIONS FOR SINGLE SUSPENSION BRACKET TRACTORS

STEP 1: (SEE FIGURE 2)

= Open parts bag labelled "A" and verify that all parts

are present.

NOTE: Place cardboard or a mat on work surface to prevent

scratching of parts removed from carton and tractor.

Ref. Part

A 43350

B 44072

C R19171616

D 44742

47674

E 48106

F 47856

G 43001

H 46584

I 43182

Qty. Description

4 Carriage Bolt, 3/8-16 x 1"

4 Whizlock Nut, 3/8"

4 Washer, 1/2"x 1"

2 Plug (486.24611 Bumper)

4 Plug (486.24612 Bumper)

2 Shoulder Bolt, 3/8-16 x .9"

2 Lag Screw, 5/16 x 3/4"

2 Hex Bolt, 3/8-16 x 1"

2 Whizlock Nut, 5/16"

2 Hex Blot, 5/16 x 3/4"

HARDWARE SHOWN FULL SiZE

EXCEPT WHERE NOTED

(not full size)

-J H

PARTS BAG "A" FIGURE 2

Call 1-866-576-8388 for missing parts or assembly help 3

DO NOT RETURN TO STORE

STEP 2: (SEE FIGURE 3)

*Remove tractor hood. (Refer to tractor manual.)

*Remove the browning shield as shown.

REMOVE

FRONT SCREWS

REMOVE

BROWNING SHIELD FIGURE 3

STEP 3: (SEE FIGURE 4)

*Place plug on a work bench or solid table and push

end of bumper down onto plug. Repeat for all plugs.

BUMPER -._

PUSH DOWN

WiTH EVEN

PRESSURE

WORK BENCH

OR SOLIDTABLE

STEP 4: (SEE FIGURE 5)

*Insert a carriage bolt into the second mounting hole

from the front of the tractor frame and fully tighten a

whizlock nut onto the bolt. Repeat on other side of

tractor.

CARRIAGE BOLT

AND WASHER

WHIZLOCK

NUT FIGURE 5

STEP 5: (SEE FIGURE 6)

*Spread ends of bumper enough to fit slots onto bolts

in rear mounting holes in tractor frame.

*The bumper has three mounting holes. The rear

hole provides the most clearance while the forward

holes provide a neater appearance. Use a hole

that provides enough clearance for hood to stay in

raised position when opened. Insert a carriage bolt

and washer through tractor frame and into desired

mounting hole on each side of bumper and secure

with a whizlock nut.

IMPORTANT: Before fully tightening nuts, be sure

tractor hood will stay in raised position when opened.

CARRIAGE BOLT

AND WASHER

FIGURE 6

4 Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

STEP 6: (SEE FIGURE 7)

*Replace the browning shield using the front screws

you removed in Step 2.

REPLACE

FRONT SCREWS

REPLACE

BROWNING SHIELD IFIGURE 7

(iNSTRUCTiONS FOR DUAL SUSPENSION BRACKET TRACTORS

STEP 1: (SEE FIGURE 2)

*Open parts bags labelled "A" and "B" and verify that

all parts needed are present.

NOTE: Place cardboard or a mat on work surface to prevent

scratching of parts removed from carton and tractor.

NOTE: Not all hardware will be used. Unused parts may be

discarded after assembly

Ref. Part

A 48894

B 43062

C 43001

D 44072

E 43003

F 44742

47674

Qty. Description

2 Self Threading Bolt, 3/8-16 x 1-1/2"

2 Hex Bolt, 3/8-16 x 1-1/2"

4 Hex Bolt, 3/8-16 x 1"

4 Whizlock Nut, 3/8"

4 Lock Washer, 3/8"

2 Plug (486.24611 Bumper)

4 Plug (486.25612 Bumper)

HARDWARE SHOWN FULL SIZE

EXCEPT WHERE NOTED

PARTS BAG "B" FIGURE 2

Call 1-866-576-8388 for missing parts or assembly help 5

DO NOT RETURN TO STORE

STEP 2: (SEE FIGURE 3)

*Remove tractor hood. (Refer to tractor manual.)

*Remove an (LT) Lawn Tractor heat shield like the one

shown. Remove a (GT) Garden Tractor heat shield

like the one shown only if you need access to inside

of tractor frame during step 5.

iMPORTANT: Be sure to re-attach the heat shield after

bumper is installed.

(LT) LAWN TRACTOR

REMOVE THIS

STYLE HEAT SHIELD

(GT) GARDEN TRACTOR

REMOVE THiS HEAT SHIELD

ONLY iF MUFFLER MUST BE

MOVED iN STEP 4.

JFIGURE 3

STEP 3: (SEE FIGURE 4)

*Place plug on a work bench or solid table and push

end of bumper down onto plug. Repeat for all plugs.

BUMPER

PUSH DOWN

WiTH EVEN

PRESSURE

WORK BENCH

OR SOLID TABLE

6 6 Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

STEP 4: (SEE FIGURE 5)

*Remove any bolts present in front mounting holes in

side of tractor frame. If bolt will not screw out of hole,

check if a nut is present on bolt on inside of frame.

On GT tractors, if access to nut is blocked by a front

mounted muffler, slide muffler down exhaust tubes to

rest on top of browning shield.

iMPORTANT: Be sure to re-attach muffler and heat

shield after bumper is installed.

• If rear mounting holes in tractor frame are empty,

install hex bolts and whizlock nuts supplied in the

parts bags. See figure 5.

(LT) LAWN TRACTOR

REMOVE BOLT iNSTALL (C), (D) IF

iF PRESENT HOLE iS EMPTY

SUSPENSION BRACKET

(LT) LAWN TRACTOR

REMOVE BOLT iNSTALL(C), (D) iF

iF PRESENT HOLE iS EMPTY

SUSPENSION

BRACKET

(GT) GARDEN TRACTOR

EXHAUST TUBES

MUFFLER

BROWNING SHIELD J

SUSPENSION BRACKET

REMOVE BOLT

IF PRESENT

FIGURE 5

STEP 5: (SEE FIGURE 6)

•Spread ends of bumper enough to fit slots onto bolts

in rear mounting holes in tractor frame.

•The bumper has three mounting holes. The rear

hole provides the most clearance while the forward

holes provide a neater appearance. Use a hole

that provides enough clearance for hood to stay in

raised position when opened. Attach the bumper

using either standard hex bolts and whizlock nuts or

self threading bolts and lock washers. Use the self

threading bolts if standard hex bolts do not insert

freely into the hole in the tractor frame.

iMPORTANT: Before fully tightening bolts, be sure

tractor hood will stay in raised position when opened.

LAWN TRACTOR (LT) SHOWN

WHIZLOCK NUT (D)

FOR BOLT (B)

(E)

FORBOLT(A)

BOLT(A)or (B)

FIGURE 6

Call 1-888-578-8388 for missing parts or assembly help 7 7

DO NOT RETURN TO STORE

(iDENTiFY YOUR TRACTOR FRAME )

For all tractors with model numbers beginning with 247, look at the side of your tractor directly underneath the hood (Figure

1A & 1B). If your frame resembles the one shown in 1A, go toTRACTORS WITH FRAME SHOWN IN FIGURE 1A on page

8. If your frame resembles the one shown in 1B, go to TRACTORS WITH FRAME SHOWN IN FIGURE 1B on page 10.

FIGURE 1A FIGURE 1B

NOTE: Only the front of the tractor frame is shown for clarity.

TRACTORS WiTH FRAME SHOWN iN FIGURE 1A

STEP 1: (SEE FIGURE 2)

*Open parts bag labelled "A" and verify that all parts

are present.

NOTE: Place cardboard or a mat on work surface to prevent

scratching of parts removed from carton and tractor.

Ref. Part Qty.

A 43350 4

B 44072 4

C R19171616 4

D 44742 2

47674 4

E 48106 2

F 47856 2

G 43001 2

H 46584 2

I 43182 2

Description

Carriage Bolt, 3/8-16 x 1"

Whizlock Nut, 3/8"

Washer, 1/2"x 1"

Plug (486.24611 Bumper)

Plug (486.24612 Bumper)

Shoulder Bolt, 3/8-16 x .9"

Lag Screw, 5/16 x 3/4"

Hex Bolt, 3/8-16 x 1"

Whizlock Nut, 5/16"

Hex Blot, 5/16 x 3/4"

HARDWARE SHOWN FULL SIZE

EXCEPT WHERE NOTED

(not full size)

_-_H

PARTS BAG "A" FIGURE 2

8 Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

STEP 2: (SEE FIGURE 3)

*Place plug on a work bench or solid table and push

end of bumper down onto plug. Repeat for all plugs.

BUMPER

PUSH DOWN

WiTH EVEN

PRESSURE

WORK BENCH

OR SOLIDTABLEI

STEP 3: (SEE FIGURE 4)

*Assemble a 0.9 x 3/8" shoulder bolt and 3/8" whizlock

nut to each side of the tractor frame. Tighten.

3/8" WHIZLOCK

NUT _. 1

SHOULDER

BOLT

FIGURE 4

STEP 4: (SEE FIGURE 5)

•Slide the lower slots of the bumper onto the shoulder

bolts you assembled to the tractor frame in step 1. e

STEP 5:

e(SEE FIGURE 6)

Assemble a 5/16 x 3/4" lag screw to the bumper and

tractor frame.

Repeat for other side.

FIGURE 6

Call 1-866-576-8388 for missing parts or assembly help 9

DO NOT RETURN TO STORE

TRACTORS WITH FRAME SHOWN iN FIGURE 1B

STEP 1: (SEE FIGURE 2)

*Open parts bag labelled "A" and verify that all parts

are present.

NOTE: Place cardboard or a mat on work surface to prevent

scratching of parts removed from carton and tractor.

Ref. Part Qty.

A 43350 4

B 44072 4

C R19171616 4

D 44742 2

47674 4

E 48106 2

F 47856 2

G 43001 2

H 46584 2

I 43182 2

Description

Carriage Bolt, 3/8-16 x 1"

Whizlock Nut, 3/8"

Washer, 1/2"x 1"

Plug (486.24611 Bumper)

Plug (486.24612 Bumper)

Shoulder Bolt, 3/8-16 x .9"

Lag Screw, 5/16 x 3/4"

Hex Bolt, 3/8-16 x 1"

Whizlock Nut, 5/16"

Hex Blot, 5/16 x 3/4"

HARDWARE SHOWN FULL SiZE

EXCEPT WHERE NOTED

..... B

(not full size)

........ H

PARTS BAG "A" FIGURE 2

STEP 2: (SEE FIGURE 3)

• Place plug on a work bench or solid table and push

end of bumper down onto plug. Repeat for all plugs.

BUMPER

PUSH DOWN

WiTH EVEN

PRESSURE

WORK BENCH

OR SOLIDTABLE SHORTSTEP

PLUG FIGURE3

10 Call 1-866-576-8388 for missing parts or assembly help

DO NOT RETURN TO STORE

Ce manuel convient aux modèles suivants

Autres manuels Craftsman Accessoires

Craftsman

Craftsman 358.792403 Manuel utilisateur

Craftsman

Craftsman 486.24276 Manuel utilisateur

Craftsman

Craftsman 390.2519 Manuel utilisateur

Craftsman

Craftsman 335.25187 Manuel utilisateur

Craftsman

Craftsman 358.792421 Manuel utilisateur

Craftsman

Craftsman 320.16494 Manuel utilisateur

Craftsman

Craftsman 358.792443 Manuel utilisateur

Craftsman

Craftsman 486.246212 Manuel utilisateur

Craftsman

Craftsman 486.24831 Manuel utilisateur

Craftsman

Craftsman 240.74295 Manuel utilisateur

Craftsman

Craftsman 509398 Manuel utilisateur

Craftsman

Craftsman 240.74291 Manuel utilisateur

Craftsman

Craftsman 509347 Manuel utilisateur

Craftsman

Craftsman 358.792450 Manuel utilisateur

Craftsman

Craftsman 486.24508 Manuel utilisateur

Craftsman

Craftsman 316.792490 Manuel utilisateur

Craftsman

Craftsman 509344 Manuel utilisateur

Craftsman

Craftsman Trimmer Products Manuel utilisateur

Craftsman

Craftsman 358.792401 Manuel utilisateur

Craftsman

Craftsman 486.24628 Manuel utilisateur

Craftsman

Craftsman 486.245992 Manuel utilisateur

Craftsman

Craftsman 944.511572 Manuel utilisateur

Craftsman

Craftsman 351.264271 Manuel utilisateur

Craftsman

Craftsman ROUTER MOUNTING KIT Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur