Cortex COR-ACC900 Manuel utilisateur

LED (green) will light up with one beep.

ACC1000

COR-ACC900

Excluded：BB-PH-2.0-.P-200

Mifare

13.56MHz

125kHz

ACC900 to ACC1000

Connector

N.O.

N.C.

COM

Door SEN

ALM

V+

V-

(125kHz)

12V

CTL

COM

N.O.

N.C.

12V

CTL

COM

N.O.

N.C.

V-

+12V

Red

Orange

Blue White

Purple White

White

Orange

Purple

Grey

Thick Red

Thick Black

N.C.

N.O.

RS232/RS-485

or USB/RS-485

Converter

Magnetic Door Contacts

Magnet Lock

(Bolt Lock)

Push Button

Strike Lock

Contact Rating：1A 125VAC/24VDC

Do not connect the reader and lock to the same power supply. Lock activation may cause reader power

instability and might affect the reader function. The door relay and the lock use the same power supply

when applying an extra relay. The reader uses an independent power supply.

V150911

COR-ACC900

Entering programming mode

Exiting programming mode

Exiting programming mode and

enabling arming status

Node ID setting (Connect to ACC1000)

Node ID setting (Connect to PC Directly)

Door relay time setting

Control mode setting

Arming delay time setting

Alarm delay time setting

Suspend or delete tag

(*=Suspend)

(9=Delete)

Setting up a batch of user to

access by card only (M6 only)

Setting up the PWD/PIN

(Access mode: Card or PIN)

Setting up the PWD/PIN

(Access mode: Card and PIN)

Arming output time setting

M4/M8: Duress code setting

M6: Public PIN setting (Card or PIN)

M4/M8: Arming PWD setting

M6: Public PIN setting (Card and PIN)

Door close time

Adding tag

Factory setting-1(Function default value)

Add/Delete tag by RF (M6 only)

Relay time of lift controller setting

Factory setting-2 (Function default value)

Real time clock setting (Stand-Alone)

Lift control setting: single door

Force open alarm setting

Delete all tag

Same Tag reading interval time

*123456# or *Master Code# (If already changed)

* #

00*NNN# (Node ID: 001~254)

02*TTT# (Door relay time: 000=Normal open) (Door relay time: 001~600=1~600 sec.)

(Door relay time: 601~609=0.1~0.9 sec.)

03*TTT# (Door relay time: 000=Normal open)

(Door relay time: 001~600=1~600 sec.)

04*N# (Mode: 4/6/8)

05*TTT# (Arming delay time: 001~600=1~600 sec.)

06*TTT# (Alarm delay time: 001~600=1~600 sec.)

07*SSSSS*EEEEE# (Input a user or a batch of user as the master card: 00000~01023)

SSSSS=Starting user address，EEEEE=Ending user address

08*N*HHMMhhmm*1111111#

N: 2 sets of auto-open zone (0: 1st set; 1: 2nd set)

HHMMhhmm=Staring time to ending time (i.e.: 08301200=08:30 to 12:00)

01111100: Sun./Mon./Tue./Wed./Thu./Fri./Sat./Holiday (0: disable; 1: enable)

09*PPPPPPRRRRRR# PPPPPP=New master code

RRRRRR=Repeat the new master code

Suspend: 10*SSSSS*EEEEE#

Delete: 10*SSSSS9EEEEE#

SSSSS=Starting user address，EEEEE=Ending user address

11*SSSSS*EEEEE# recover the paused tag

SSSSS=Starting user address，EEEEE=Ending user address

11*SSSSS*EEEEE#

SSSSS=Starting user address，EEEEE=Ending user address

12*UUUUU*PPPP# UUUUU=User address

PPPP=4-digit individual PWD

13*UUUUU*PPPP# UUUUU= User address

PPPP=4-digit individual PWD

14*TTT# (Arming output time: 001~250=1~250 sec.)

15* PPPP# PPPP=4-digit individual PWD

P.S. Duress code will be unavailable and become a public PIN at access mode “Card or PIN” of M6

16*UUUUU*SSSSSCCCCC# UUUUU= User address，SSSSS=5-digit site code

CCCCC=5-digit card code

17* PPPP# PPPP=4-digit individual PWD ( default value=1234; disable Arming PWD=0000)

P.S. Arming PWD code will be unavailable and become a public PIN at access mode “Card PIN” and of M6

18*TTT# (Door close time: 001~600=1~600 sec.; default value: 15 sec.)

19*UUUUU*QQQQQ# UUUUU=User address，QQQQQ=Pieces of card

20*DDD# (Please refer to function default value for details)

21*UUUUU*S*FFFFFFFF# UUUUU=User address

S: 4 sets of lift control (Input: 0~3)，FFFFFFFF: 8 floors/stop setting (0=Disable, 1=Enable)

22*N# N=0=Delete tag ，N=1=Add tag

23*NNN*TTT# N=Node ID of lift controller，TTT= relay time: 000~600=1~600 sec.

24*DDD# (Please refer to function default value for details)

25*YYMMDDHHmmSS# YYMMDDHHmmSS: Year/Month/Day/Hour/Min./Sec.)

26*SSSSS*EEEEE*N# SSSSS=Starting user address，EEEEE=Ending user address

N=0=Enable; N=1=Disable; N=2=Initial

27*UUUUU*FF# UUUUU=User Address，FF=Floor number (01~32 floor/stop)

28**NNN# NNN=000=Disable ，NNN=128=Enable

29*29*#

31*TTTT# TTTT=0100=1 Sec. (Base on 10ms, TTTT range from 10~6500=0.1-65 sec.)

Master card setting

Auto-open zone setting

Recover tag

Card number modification

Lift control setting: multi-doors

Anti-pass-back (Enable user)

Master code setting

Alarm relay time setting

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

M4/M8

M4/M6/M8

Command List

* * #

00*NNN*VVV*nnn# (NNN: Node ID) (VVV: Virtual ACC Node ID) (nnn: Door Number)

Ex.: Input 00*002*002*002# for 2nd door in system

V150911

COR-ACC900

Time Attendance

Auto Re-lock

Auto Open

Exit by Push Button

Master Reader of Network

Access/Exit Reader

Anti-pass-back

Yes*

Disable*

Disable

Slave*

Exit*

Disable*

Enable

Enable*

Master

Access

Enable

001

002

004

016

032

064

128

Networking

Networking/Stand-Alone

Networking

Function Option

0 1 Value Application Function Option

0 1 Value Application

Function Default Value

Programming

A、20*DDD#

Remarks:

*: default value

Option 0= none value

Option 1= 1 x each value (i.e. DDD value of Enable “Auto Open” +

”Exit by Push Button + ”Anti-pass-back” =004+016+128=148;

As a result, the command will be 20*148# .)

B、24*DDD#

Auto-open door without

presenting card at auto

open zone

Alarm Output*

Stop Alarm by…

Door bell

Alarm Output/Lift Control

064

128

001

002

Networking /

Stand-Alone

Networking /

Stand-Alone

Networking /

Stand-Alone

Networking /

Stand-Alone

Networking /

Stand-Alone

Push Button /

Door Closed

Enable

Lift Control

Enable

None*

Disable*

Function Option

01Value Application

C、28*DDD#

Force Open Alarm

Output Disable* Enable 128

A、Entering and Exiting Programming Mode

Entering Exiting

*123456# or *Master Code# (If already changed) * #

B、Initial Setup

1.Restoring Factory Settings

Access programming mode *123456# or *Master Code#

(If already changed) → 20*000# → 24*000# →

26*00000*01023*2# → 28*000# → 29*29*# → Changing

the Master Code to default value:123456→ *# (done)

C、Setting up the control mode (M4/M6/M8)

Access programming mode *123456# or *Master Code# personal ID (If already changed)

→ 04*N# (Input: 4/6/8)

1.Individual PWD (M4/M8)

a.Card or PIN

Access programming mode

*123456#

*Master Code#

(If already changed)

→ 12*UUUUU*PPPP#

(i.e. User

address: 00001 and PWD: 1234, input 12*00001*1234#)

2.Changing the Master Code

Access programming mode *123456# or *Master Code#

(If already changed) → 09*PPPPPPRRRRRR# (Input the

6-digit new master code twice)

3.Changing the Node ID of Reader

Access programming mode *123456# or *Master Code#

(If already changed) → 00*NNN# (Node ID: 001~254)

b.Card and PIN

Access programming mode

*123456#

*Master Code#

(If already changed)

→ 13*UUUUU*PPPP#

(i.e. User address:

00001 and PWD: 1234, input 13*00001*1234#)

2.Public PWD (M6)

a.Card and PIN

Access programming mode

*123456#

*Master Code#

(If already changed)

→ 17* PPPP#

(Input 4-digit PWD, default value: 1234)

b.PIN only

Access programming mode

*123456#

*Master Code#

(If already changed)

→ 15* PPPP#

(Input 4-digit PWD)

E、Anti-pass-back

Usually, anti-pass-back is commonly applied to parking areas or

elsewhere user wants to monitor not only the access but also exit

condition.

Enable device

Access programming mode → 20*128# please refer to “20*DDD#”

function default value for additional function value

Enable card user

Access programming mode → 26*SSSSS*EEEEE*0#

(i.e. User address from 00001 to 00005 enable the anti-pass-back

function: 26*00001*00005*0#

F、Auto Open Zone

Door will remain opening after first person flashes card. ACC900 only supports two sets

of auto-open zone by device setting, but auto-open zone can be extended up to 63 sets if

connected to ACC1000.

Enable/Disable auto open zone

Access programming mode 20*004# please refer to “20*DDD#” function default value for

additional function value

Enable/Disable auto open door without presenting card

Access programming mode 24*001# please refer to “24*DDD#” function default value for

additional function value

Setting up open time

Access programming mode → 08*N*HHMMhhmm*01111100#

N: 2 sets of auto-open zone (N=0=1st set; N=1=2nd set)

HHMMHHMM=staring time to ending time (i.e.: 08301200=08:30 to 12:00)

D、Setting up the password

(Default Value)

V150911

COR-ACC900

Abnormal

Single Tag

RF Learn Function

Access programming

mode

*123456# or

*Master Code#

(If already changed)

19*UUUUU*QQQQQ#

UUUUU=5-digit User

Address: 00000~01023

QQQQQ: Input 00001

(Only one tag)

(i.e. 19*00001*00001)

Close Tag into RF Area

Present the tag to the

controller.

(Memory location

number)

Random Tag NO.

Access programming

mode

*123456# or

*Master Code#

(If already changed)

19*UUUUU*QQQQQ#

UUUUU=5-digit User

Address:00000~01023

QQQQQ: Input 00001

Close Tag into RF Area

Present the tag to the

controller.

(Memory location number)

The First tag has now been

added, present the rest of

the tags one after the other

to add them to the system

as well.

Sequential Tag NO.

Access programming

mode

*123456# or

*Master Code#

(If already changed)

19*UUUUU*QQQQQ#

UUUUU=5-digit User

Address: 00000~01023

QQQQQ: Input 5-digit tag

units: Enter the quantity

of tags to be added.

(i.e.: 10 pcs of sequential

tag=00010)

Close Tag into RF Area

Present the tag with the

lowest number to the

controller.

(Memory location number)

A Batch of Tags

Adding Tag (M4/M8) Deleting Tag (M4/M8)

Single Tag

Memory Location

A Batch of Tags

Memory Location

Delete All Tags

Access programming

mode

*123456# or

*Master Code#

(If already changed)

10*SSSSS9EEEEE#

9=Delete

SSSSS=starting user

address

EEEEE=ending user

address

(i.e. Delete User Address

00003=10*00003900003)

Done

Access programming

mode

*123456# or *Master Code#

(If already changed)

10*SSSSS9EEEEE#

9=Delete

SSSSS=starting user

address

EEEEE=ending user

address

(i.e. Delete User Address:

00004~00010=10*00004900010)

Done

Access programming

mode

*123456# or

*Master Code#

(If already changed)

29*29*#

Done

M4/M8 (Default Value: M4)

Deleting Tag (M6)

Access programming

mode

*123456# or

*Master Code#

(If already changed)

11*SSSSS*EEEEE#

SSSSS=starting user

address=5-digit card code

EEEEE=ending user

address=5-digit card code

(i.e. Add a tag with card

code 15031=

11*15031*15031)

(i.e. Add a batch of tag

with card code

15031~15038=

11*15031*15038)

Done

Access programming

mode

*123456# or

*Master Code#

(If already changed)

10*SSSSS*EEEEE#

10*SSSSS9EEEEE#

SSSSS=starting user

address=5-digit card code

EEEEE=ending user

address=5-digit card code

(i.e. Delete a tag with card

code 15031=

11*15031*15031)

(i.e. Delete a batch of tag

with card code

15031~15038=

11*15031*15038)

Done

Access programming

mode

*123456# or

*Master Code#

(If already changed)

29*29*#

Done

Adding Tag (M6)

Delete Single/A Batch Tag Delete All Tag

Enable: Access programming mode

→ press * * #

Disable: Access programming mode

→ press * #

Enable/Disable: Flash card +

press 4 digit arming PWD PPPP#

(default: 1234)

By Keypad By flashing card + Arming PWD

Q: How to enable/disable the arming status?

To set how long the door relay (lock release) is active after presenting a card.

Range: 0 ~ 600 (sec.); 601~609 (0.1~0.9 second)

To set value “0” will make door remain opening till card presented again, then door close. (Default value: 7 sec.)

To set how long the door contact can remain opening before activating the alarm.(Default value: 15 sec.)

When an alarm condition has arisen, the alarm will activate for this duration. Range: 1 ~ 600 (sec.)

To set value “0” will make alarm relay keep on until disarming, then alarm relay off. (Default value: 7 sec.)

To delay the activation of the alarm relay after an alarm condition has arisen, so that user can have enough time

to disable alarm. (Default value: 1 sec.)

To delay the time of enabling arming, so that user can have enough time to disable arming.

Range: 1 ~ 600 (sec.) (Default value: 1 sec.)

Activate the alarm immediately w/o having any alarm delay TM

Command

Adding and Deleting Tag

V150911

Autres manuels Cortex Contrôleurs d'accès IP

Cortex

Cortex COR-ACC980 Manuel utilisateur

Manuels Contrôleurs d'accès IP populaires d'autres marques

ZKTeco

ZKTeco SpeedFace-V5L Manuel utilisateur

Jantar

Jantar REX A-1-9 Manuel utilisateur

2N Access Unit Feuille d'instructions

Kedacom

Kedacom KSCA120 Series Manuel utilisateur

H3C

H3C WX2880X Manuel utilisateur

G4S

G4S S870-EX Mode d’emploi

PRASTEL

PRASTEL M2000PE Manuel utilisateur

Allegion

Allegion interflex IF-281 Cylinder Manuel utilisateur

TECOM

TECOM TS1067E Manuel utilisateur

Fermax

Fermax Memokey 100C Guide de l'utilisateur

Fermax

Fermax CITYLINE MEMOKEY Mode d’emploi

Software House

Software House iSTAR Pro 2U RM Mode d’emploi

AKCP

AKCP SP+ Manuel utilisateur

Bpt

Bpt HNA/102 Manuel utilisateur

Civintec

Civintec CV9601T-T-1F Manuel utilisateur

BioMax

BioMax N-X90W Manuel utilisateur

ZKTeco

ZKTeco OP-200 Manuel utilisateur

FingerTec

FingerTec s-Kadex Manuel utilisateur