Cortelco 1203 Guide de configuration
O
IM
WNER'S
NSTRUCTION ANUAL
MODEL 1203
Carefully read the instructions in this manual.
Follow all warnings and instructions marked on the unit.
When cleaning, unplug the telephone jack from the wall outlet. Use
a damp cloth. use liquid or aerosol cleaners.
Do not use this equipment near water, eg: near a kitchen sink,
bathtub, washbowl, laundry rub, swimming pool or in a wet
basement.
Install in a protected location. Ensure all lines and cords are away
from foot traffic. place objects on the line cord that may
cause damage or abrasion.
Avoid spilling any liquid on the unit. This may cause internal
shorting, fire or shock and is not covered under your warranty.
Do not overload wall outlets and extension cords as this can result
in the risk of fire or electrical shock.
Never push objects of any kind into this telephone as they can
touch dangerous voltage points or short out parts that could result
in a risk of fire or electrical shock.
Take the phone to a qualified technician when it requires repair
work or service. To reduce the risk of electrical shock, do not
disassemble the telephone. Opening or removing covers can
expose you to dangerous voltages or other risks. Incorrect re-
assembly can cause electrical shock during subsequent use.
Avoid using the telephone during an electrical storm. There can be
a slight risk of electrical shock from lightning.
use the telephone to report a gas leak, if in the vicinity of
the leak.
Unplug this telephone from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
If liquid is spilled into the unit.
If the unit is exposed to rain or water.
If the unit does not operate normally by following the
operating Instructions.
If the unit is dropped or the casing is damaged.
If the unit exhibits a distinct change in performance.
DO NOT
DO NOT
DO NOT
l
l
l
l
l
1.
To reduce the risk of fire, electrical shock, and injury, please follow
these basic safety precautions before you use this equipment.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
7
SAFETY INSTRUCTIONS
4
LOCATION OF CONTROLS
1
6
WALL INSTALLATION
3
Screw head
Wall
Desk tab
position
Wall mount
tab position
diagram 1
diagram 3
8.3cm
Slide the handset tab out and rotate it 180 degrees so that the hook
points up. This will hold the handset in the cradle when the phone is
mounted on the wall.
Remove the desk stand from the phone base (see diagram 2).
Mount the phone on a standard telephone wall jack.
1.
2.
3.
diagram 2
1
Hook Switch Message lamp
Volume
Speaker
Memory
(M1~M5)
VIP
MUTE
HOLD
Memory
(M6~M10)
Handset REDIAL
AUTO
SET
FLASH
RING
VOL. VOL.
SET
AUTO
PAUSE
FLASH
REDIAL
VIP1
VIP2
MUTE
HOLD
M1
M2
M3
M4
M5
M7
M6
M8
M9
M10
Ringer volume
switch
5
Flash time
switch
Dialing mode
switch
2
B. To dial the number in memory
AUTO
0~9
1. Lift the handset.
2. Press .
3. Press the desired Memory Button ( ).
1. Lift the handset.
2. Dial *#0000*#.
3. Hang up the handset.
11. Hold button
13. Pause button
To place a call on hold, press and hang up the handset. To retrieve the
call lift the handset or go off hook on any other phone connected to the line.
HOLD
The Headset jack will accept a 2.5mm headset plug. Please connect the
headset before beginning a call. Press button once to make or answer a
call. Press it again to end the call.
12. Headset button
14. Phone resetting
Pressing this button will insert a 3 second pause in the dialing sequence. This
is intended to be used with memory dialing.
Resetting the phone will erase all memory dial numbers and the redial
memory.
This switch is located on the bottom of the telephone. For Tone Dialing, set
the switch to the T position. For Pulse Dialing, set the switch to the P position.
This feature allows you to redial the last phone number dialed.
You can adjust the flash time by using this switch located on the bottom of
your phone. There are 3 levels available, , and (ms).
There are 3 ringer levels ( , , and ). These may be selected by this
switch on the bottom of the telephone.
1. Dial mode switch
Redial function
3. Mute function
4. Flash button
Flash time switch
6. Ringer volume switch
100 300 600
HI LO OFF
2.
5.
a. Lift handset.
b. Press .REDIAL
This feature allows you to turn off your telephone's microphone so that the
other party cannot hear you.
Press FLASH instead of pressing the hook switch to activate services such as
Call Waiting or 3-Way Calling, or to activate certain PBX or Centrex features.
You may be required to press other buttons before or after you press .
Refer to the custom calling instructions provided by your local telephone
company or to the operating instructions provided with your PBX.
FLASH
3
OPERATIONS
2
Press the or buttons to adjust the receive volume during a
conversation. There are 4 levels. This button controls both the speaker and
handset receive levels.
There are 12 memory locations ( , and ) .
1. Lift the handset.
2. Press .
3. Dial the number to be stored (Press to insert a pause).
4. Press .
5. Press the desired Memory Button.
1. Lift the handset.
2. Press the desired Memory Button.
1.
2.
3.
4.
5.
7. Speaker button
9. One-touch memory
10. Two-touch memory
VOL.+ VOL.-
M1~M10 VIP1 VIP2
A. To store a number to memory
SET
PAUSE
SET
B.
A. To store a number to memory
Use this button to activate the Speakerphone.
Turn on: Press the button. Hang up the handset if you are off hook.
Turn off: To end a call, press the button. To continue a call, lift the
handset.
A.
B.
8. Volume setting
To dial a number stored in memory
There are 10 two-touch memory locations.
Lift the handset.
Press .
Dial the number to be stored (Press to insert a pause).
Press .
Press the desired Memory Button ( ).
SET
PAUSE
SET
0~9
4
Table des matières
Autres manuels Cortelco Téléphone
Cortelco
Cortelco Tel-Flash 2500 Guide de configuration
Cortelco
Cortelco VALUE 2500 VBA-20MD Series Manuel utilisateur
Cortelco
Cortelco Select 3719 Guide de configuration
Cortelco
Cortelco ITT-9150-ASH Manuel utilisateur
Cortelco
Cortelco 5150 Guide de configuration
Cortelco
Cortelco 3691 Guide de configuration
Cortelco
Cortelco 915044V0E21J Manuel utilisateur
Cortelco
Cortelco COLLEAGUE 2220 Manuel utilisateur
Cortelco
Cortelco Colleague 2202 Guide de configuration
Cortelco
Cortelco COLLEAGUE 2220 Guide de configuration
Cortelco
Cortelco 8599 Guide de configuration
Cortelco
Cortelco 8780 Manuel utilisateur
Cortelco
Cortelco 2554XX-VBA-20MT Guide de configuration
Cortelco
Cortelco Tel-Flash 2500 Guide de configuration
Cortelco
Cortelco VR16SS Guide de configuration
Cortelco
Cortelco Colleague 2200 Manuel utilisateur
Cortelco
Cortelco 9150 Manuel utilisateur
Cortelco
Cortelco 3693 Guide de configuration
Cortelco
Cortelco 2750 Guide de configuration
Cortelco
Cortelco 2005 Guide de configuration
