Cornelius Millenium II Manuel utilisateur

Millennium II-Water Inlet Replacement Installation Instructions

INSTALLATION INSTRUCTIONS

Millennium II

SAFETY INSTRUCTIONS

WARNING:

Before starting installation, read and understand all safety label and warnings on the machine. Also review and

understand all safety instructions in the owners, installation and service manuals.

Failure to comply could result in serious injury, death or damage to the equipment.

QUALIFIED SERVICE PERSONNEL

WARNING:

Only trained and certified electrical, plumbing and refrigeration technicians should service this unit.

All wiring and plumbing must conform to national and local codes. Failure to comply could

result in serious injury, death or equipment damage.

SAFETY PRECAUTIONS

This unit has been specifically designed to provide protection against personal injury. To ensure continued

protection observe the following:

WARNING:

Disconnect power to the unit before servicing. Follow all lock out/tag out procedures established by the user. Verify all

power is off to the unit before performing any work.

Failure to comply could result in serious injury, death or damage to the equipment.

CAUTION:

Always be sure to keep area around the unit clean and free of clutter.

Failure to keep this area clean may result in injury or equipment damage.

Revision Date: March 24, 2014 www.cornelius.com Revision: C

Millennium II-Water Inlet Replacement Installation Instructions

WATER INLET REPLACEMENT

This instruction sheet details the procedure for replacing the water inlet fitting at the valve. All necessary material to

make the change, along with this bulletin, is included in the kit. The kit contents are listed below. Note that this kit

will work for all models, regardless of voltage.

Procedure

1. Turn off the water supply to the dispenser. Disconnect power from the dispenser. Remove the top panel

and merchandiser. Note that there are two harnesses from the top panel and one from the merchandiser

that must be disconnected. Make sure to mark the harnesses so as not to incorrectly wire them during re-

assembly. Next remove both side panels by sliding them towards the front of the dispenser.

2. Remove the hitch pins that secure the refrigeration deck to the waterbath housing. Carefully lift the

refrigeration deck out of the waterbath to access the manifold.

Figure 1.

3. Remove the water inlet fittings from the back of the valve (Figure 1.) These are the fittings attached to the

3-inch piece of tubing that runs from the manifold. Also remove this tubing from the manifold. Discard both

the fitting and the tubing for all valves.

4. If not already done, install the new o-ring to the new fitting. Attach this fitting to a 3-inch piece of tubing with

a clamp, and then attach this assembly to the manifold (clamps, tubing and fittings supplied in kit). Install

the fitting into the valve. Repeat for remaining valves.

5. Turn on the water supply to the dispenser and check for leaks. If any leaks are discovered, turn off supply

and re-install the fitting into the valve.

6. Install and secure the refrigeration deck into the waterbath, and install the side panels, top panel and

merchandiser. Making sure to properly connect the harnesses and interlock all cladding pieces. DO NOT

force any panels together. During proper assembly, the panels will slide together easily and remain

interlocked. Connect power to the dispenser.

Table 1. Millennium II-Kit No. 629087501

Part number Description Qty

77050300 Fitting 6

31525003 O-Ring 6

40502 Clamp 12

50299 Tubing 18 in.

620919561 Instruction Sheet

Table des matières

Autres manuels Cornelius Distributeur

Cornelius

Cornelius ED22 Series Manuel utilisateur

Cornelius

Cornelius Nueva Tower Manuel

Cornelius

Cornelius NITROPRO MINI Manuel utilisateur

Cornelius

Cornelius Remcor TJ45-D Manuel utilisateur

Cornelius

Cornelius QUEST CAFE Guide de configuration

Cornelius

Cornelius REMCOR OLYMPUS POST-MIX Manuel utilisateur

Cornelius

Cornelius QUEST ELITE QLT 2000 Manuel

Cornelius

Cornelius Enduro 200 Manuel utilisateur

Cornelius

Cornelius IDC PRO 255 Manuel utilisateur

Cornelius

Cornelius NITROPRO MINI Manuel utilisateur

Cornelius

Cornelius QUEST 4000 Manuel utilisateur

Cornelius

Cornelius IDC 255 Manuel utilisateur

Cornelius

Cornelius Flavor OverLoad CG5017-1007 Manuel utilisateur

Cornelius

Cornelius NITROPRO MINI Manuel utilisateur

Cornelius

Cornelius VIPER Manuel utilisateur

Cornelius

Cornelius 2230 K4-100 Manuel utilisateur

Cornelius

Cornelius SUBWAY PEPSI SPIRE 3.0 Guide de configuration

Cornelius

Cornelius FCB OVERCOUNTER POST-MIX DISPENSER Manuel utilisateur

Cornelius

Cornelius IDC175-HD Manuel utilisateur

Cornelius

Cornelius HELIX Manuel utilisateur

Cornelius

Cornelius ED2XX-B Series Manuel utilisateur

Cornelius

Cornelius Quest Elite 2000 Manuel utilisateur

Cornelius

Cornelius ABS 2.0 Manuel utilisateur

Cornelius

Cornelius IDC Pro Mode d’emploi

Manuels Distributeur populaires d'autres marques

Silver King

Silver King Majestic SK12MAJ Guide de démarrage rapide

Franke

Franke F3Dn Twin Manuel utilisateur

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manuel utilisateur

DAN DRYER

DAN DRYER 282 Manuel utilisateur

Essity

Essity Tork 473208 Manuel utilisateur

CBS

CBS SD300BU-88 Guide de configuration

Sealey

Sealey MK77 Manuel utilisateur

Fluid Management

Fluid Management Accutinter 1600 Manuel utilisateur

Franke

Franke DVS SD99-010 Manuel utilisateur

Graco

Graco Dispensit 1053-10C Guide de dépannage

ITALTINTO

ITALTINTO i50 Manuel utilisateur

Coca-Cola

Coca-Cola FREESTYLE 9000 Manuel utilisateur

Graco

Graco ProMix 2KE Mode d’emploi

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manuel utilisateur

Wayne

Wayne GLOBAL VISTA CNG Manuel utilisateur

clarsen

clarsen H133 Manuel utilisateur

PicoBrew

PicoBrew Zymatic Manuel utilisateur

BOWMAN

BOWMAN BP-007 Manuel utilisateur