Cornelius Pre-Mix Dispenser Universal C-750 Manuel utilisateur

November 13, 2002

185211001

IMI Cornelius Inc, 1989–2002

Revision:A

IMI CORNELIUS INC.

One Cornelius Place

Anoka. MN 55303-6234

Telephone (800) 238–3600

Facsimile (763) 422–3246

WATER TANK SEAL KIT (P/N 308979000)

UNIVERSAL C-750 PRE-MIX DISPENSER

These Instructions outline installation of the Water Tank Seal Kit (P/N 308979000) on the Universal C-750

Pre-Mix Dispenser.

DISPENSER

INSULATED

REFRIGERATION

LINE

NO TAG

2185211001

NOTE: Only qualified personnel should install this kit.

1. Unpack loose–shipped parts. Make sure all parts are present and in good condition.

Table 1. Loose-Shipped Parts

Item

No. Part No. Name Qty.

1 200468012 Sheet Metal Screw, Phil Truss Hd, No. 8 by 3/4-in. 12

2 308981044 Front Cover Plate 1

3 308982044 Back Cover Plate 1

4 313093000 Plug, 2-in. 1

5 172127000 Plug 1

6 960265000 Permagum Sealer,12-in. long 1

8 960115000 Rubatex Insulation,1/8 by 1/2-in. (78-in. long) 1

INSTALLING WATER TANK SEAL KIT

IMPORTANT: This kit is intended to seal the water tank to prevent leakage from splashing water when

moving or transporting the Dispenser. IT IS NOT INTENDED THAT THE DISPENSER MAY BE LAID ON

IT’S SIDE WHEN WATER TANK IS FULL OF WATER.

1. If Dispenser is in operation, place power switch on back of Dispenser in ‘‘OFF’’ position.

2. Remove four screws securing Dispenser top cover, then lift cover straight up and off.

NOTE: Front of Dispenser is the side facing the dispensing valves.

3. Place RUBATEX INSULATION (item NO TAG) all the way around outer edges of FRONT COVER PLATE

(item 2) and BACK COVER PLATE (item 3) as shown in illustration. FILL ANY GAPS AT BUTT EDGES

OF RUBATEX INSULATION WITH SMALL PIECES OF PERMAGUM SEALER (item 6).

4. Place FRONT COVER PLATE (item 2) in position on top of water tank as shown in illustration. IT MAY BE

NECESSARY TO VERY CAREFULLY REFORM OR REPOSITION INSULATED REFRIGERATION LINE

ANGLE TO FIT INTO CUTOUT AREA IN CORNER OF FRONT COVER PLATE.

5. Secure back side of front cover plate to agitator motor support plate with four THREAD CUTTING

SCREWS (item NO TAG).

6. Secure rest of front cover plate to plastic motor tank rim with six SHEET METAL SCREWS (item 1). DO

NOT OVERTIGHTEN SCREWS INTO PLASTIC.

7. Place BACK COVER PLATE (item 3) in position on top of water tank as shown in illustration.

8. Secure front side of back cover plate to agitator motor support plate with four THREAD CUTTING

SCREWS (item NO TAG).

9. Secure rest of back cover plate to plastic water tank rim with five SHEET METAL SCREWS (item 1). DO

NOT OVERTIGHTEN SCREWS INTO PLASTIC.

10. Place PLUG (item 4) in agitator motor plate water fill hole.

1852110013

11. If installing kit on a four-flavor Dispenser, install PLUG (item 5) in 1/2-inch hole in top of agitator motor

plate.

12. Fill area between insulated refrigeration line and cutout area in front cover plate with PERMAGUM SEAL-

ER (item 6). Also, overlap front cover plate and insulated refrigeration line with permagum sealer to prevent

water leak.

13. If new Dispenser installation, refer to manual provided with Dispenser and complete installation as

instructed.

14. Install Dispenser top cover and secure with four screws.

15. If Dispenser was in operation before start of Kit installation, place power switch in ‘‘ON’’ position.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Cornelius Accessoires

Cornelius

Cornelius Linus Series Manuel utilisateur

Cornelius

Cornelius COR15BBCD Manuel utilisateur

Cornelius

Cornelius Energize Series Mode d’emploi

Cornelius

Cornelius Universal 750 Pre-Mix Manuel utilisateur

Cornelius

Cornelius Triton Series Mode d’emploi

Cornelius

Cornelius Energize 1 HC Series Manuel utilisateur

Cornelius

Cornelius Door Latch Manuel utilisateur

Cornelius

Cornelius Energize 2 HC Manuel utilisateur

Cornelius

Cornelius P/N 620037008 Manuel utilisateur

Cornelius

Cornelius Energize Series Manuel utilisateur

Cornelius

Cornelius Remcor 2849949020 Manuel utilisateur

Cornelius

Cornelius P/N 631500074 Manuel utilisateur

Cornelius

Cornelius Maxi series Manuel utilisateur

Cornelius

Cornelius Energize IntelliBlue Duette 3 Glycol Manuel

Cornelius

Cornelius COR9530UBCST Manuel utilisateur

Cornelius

Cornelius Duette 3 Manuel utilisateur

Cornelius

Cornelius P/N 620043511 Manuel utilisateur

Cornelius

Cornelius CR R134a Series Mode d’emploi

Cornelius

Cornelius Post-Mix Valves UFB-1 Guide d'installation

Cornelius

Cornelius Triton 200 HC Mode d’emploi

Cornelius

Cornelius 000 PLUS Manuel utilisateur

Cornelius

Cornelius Energize Series Manuel

Cornelius

Cornelius Triton HC Series Mode d’emploi

Cornelius

Cornelius Refillable Bottle Kit 720401106 Guide de configuration

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur