Cooper Lighting Corelite Manuel utilisateur

WARNINGS

1). WARNING! Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

2). WARNING! - Risk of Fire/Electric Shock. If not qualiﬁed, consult an electrician.

3). WARNING! – Risk of ﬁre or electric shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when

drilling for installation of reﬂector kit hardware. Check for enclosed wiring and components.

4). WARNING! – Avoid contact with LED modules.

NOTES

1). NOTE! - This product must be installed in accordance with the applicable installation code by a certiﬁed

electrician, familiar with the construction and operation of the product and hazards involved.

2). NOTE! - Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit

installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

3). NOTE! - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.

4). NOTE! - Disconnect all power before proceeding.

5). NOTE! - “Doghouse” component on end of ﬁxture is intended for T8 lamping only. A maximum of (8) ﬁxtures can be

mounted in a continuous row with each “Doghouse” facing the opposite direction starting from the center of the run.

Class R6 LED or Fluorescent

Installation Instructions - page 1 of 2

Corelite 18001 East Colfax Ave. Aurora, CO 80011 Ph. (303) 393-1522 Fax (303) 393-1477

ADE111698 rev 021213

1. Unpack ﬁxture from box.

3. To install ﬁxture into grid, raise it through an adjacent cell and then into the cell

where it is to be installed.

5. After securing ﬁxture tabs to grid frame, use holes in tabs to tie ﬁxture back to

structure at all four corners or per local code.

2. If installing an LED ﬁxture, leave the lens installed during installation. If install-

ing a ﬂuorescent module, the lens should be left installed until just prior to

installing lamps.

4. Bend all four side tabs out and secure ﬁxture to grid.

6. Make appropriate wire connections adhereing to local electrical code.

If installing an LED ﬁxture,

this is the ﬁnal step. If

installing a ﬂuorescent

ﬁxture, go to page 2.

WARNINGS

1). WARNING! Risk of Electric Shock. Disconnect power at fuse or circuit breaker before installing or servicing.

2). WARNING! - Risk of Fire/Electric Shock. If not qualiﬁed, consult an electrician.

3). WARNING! – Risk of ﬁre or electric shock. Luminaires wiring, ballasts, or other electrical parts may be damaged when

drilling for installation of reﬂector kit hardware. Check for enclosed wiring and components.

4). WARNING! – Avoid contact with LED modules.

NOTES

1). NOTE! - This product must be installed in accordance with the applicable installation code by a certiﬁed

electrician, familiar with the construction and operation of the product and hazards involved.

2). NOTE! - Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit

installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

3). NOTE! - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.

4). NOTE! - Disconnect all power before proceeding.

5). NOTE! - “Doghouse” component on end of ﬁxture is intended for T8 lamping only. A maximum of (8) ﬁxtures can be

mounted in a continuous row with each “Doghouse” facing the opposite direction starting from the center of the run.

Class R6 Fluorescent

Installation Instructions - page 2 of 2

Corelite 18001 East Colfax Ave. Aurora, CO 80011 Ph. (303) 393-1522 Fax (303) 393-1477

ADE111698 rev 021213

1. Remove lens.

3. Replace the lens.

2. Insert T5 or T8 ﬂuorescent lamp into the ﬁxture. For T8 lamping, install one

end of the lamp into the socket inside the “doghouse” compartment ﬁrst. Then

install the other end and make sure the lamp is secure.

Ce manuel convient aux modèles suivants

Autres manuels Cooper Lighting Lampe de travail

Cooper Lighting

Cooper Lighting McGraw-Edison EPL/DLS Envoy Manuel utilisateur

Cooper Lighting

Cooper Lighting IRIS E4LWW Manuel utilisateur

Cooper Lighting

Cooper Lighting LED110 Manuel utilisateur

Cooper Lighting

Cooper Lighting SURE-LITES Photoluminescent Exit Signs Manuel utilisateur

Cooper Lighting

Cooper Lighting PHL300 Manuel utilisateur

Cooper Lighting

Cooper Lighting MCL5 Manuel utilisateur

Cooper Lighting

Cooper Lighting PQS45 Manuel utilisateur

Cooper Lighting

Cooper Lighting PQS45 Manuel utilisateur

Cooper Lighting

Cooper Lighting McGraw-Edison IMI-6950 Manuel utilisateur

Cooper Lighting

Cooper Lighting Sure-Lites CCX Series Manuel utilisateur

Cooper Lighting

Cooper Lighting LED120 Manuel utilisateur

Manuels Lampe de travail populaires d'autres marques

ANSMANN

ANSMANN POWERLIGHT 5.1 Manuel utilisateur

RTRMAX

RTRMAX RTX1868 Manuel utilisateur

FeinTech

FeinTech LAL00220 Manuel utilisateur

Bunker Hill Security

Bunker Hill Security 64735 Manuel utilisateur

Goobay

Goobay 30450 Manuel utilisateur

REV Ritter

REV Ritter SPOT Manuel utilisateur

Ignition

Ignition Stagepix Line 100 IP Manuel utilisateur

SCANGRIP

SCANGRIP DUO CONNECT Manuel utilisateur

Bosch

Bosch GLI 18 V Manuel utilisateur

Bayco

Bayco SL-1514 Manuel utilisateur

EUFAB

EUFAB SMD LED 8+1 Manuel utilisateur

DeWalt

DeWalt DCL510 Manuel utilisateur

PowerSmith

PowerSmith PWLD080T Manuel utilisateur

MaxLite

MaxLite 73683 Manuel utilisateur

Heitronic

Heitronic Trend 27867 Manuel utilisateur

Monzana

Monzana Gore MZCL10 Manuel utilisateur

EINHELL

EINHELL TE-CL 18/2000 LiAC Manuel utilisateur

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manuel utilisateur