CoolGear USBG-7DU2 Manuel utilisateur

Thank you for purchasing this high-speed 7-portUSB2.0hub.It

providesanidealsolutiontoexpand7 USB2.0 ports from one

single USB2.0hostport.Itprovidesaself power source

(+7~24VDC from 2-pin Terminal Blocks) to provide enough

power on USB2.0 buses.

Features:

Compliant with USB Specification Revision 2.0

Rigid and Wall-mountable Metal Case

Supports High-speed and or Full-speed Packet

Protocol Sequencer for Endpoint 0/1

Provides 7 Downstream Facing Ports

Supports USB Screw Lock Mechanism Increases Reliability

Supports 480Mbps, 12Mbps and 1.5Mbps Speed

Supports Self-powered and Bus-powered Mode

CoolGear USBG-7DU2 7-Port USB2.0

Metal Hub with DIN RAIL Mounting Kit

Installation Guide

1. Introduction

2. Connector Layout

P o w e r L E D

7 Downstream Ports

Upstream Port

Connector

Self Po w e r I n p u t

Connectors

7-Port USB2.0 Metal Hub with DIN RAIL Mounting Kit

Upstream Port Connector: Type-B connector from upstream

USB2.0port.ItisconnectedfromhostoranotherUSB2.0

hub.

Self Power Input Connectors: This 2-pin (one pin plus voltage

and the other pin is GND) terminal block connectors are

used to connect strong power to self-power the h u b , the

voltage can be in the range from +7V to 24VDC.

Warning!!

Please make sure the polarity of the input power should be

correctly match the terminal block pins, otherwise it will

damage the hub.

1. Use static electricity discharge precautions.

Remove possible static discharge potential from any

objects that the hub may come in contact with before

installation. This can be accomplished by touching a bare

metal chassis rail after you have turned off the power.

2. Apply DC power (range from +7V to 24V) to the 2-pin

Terminal Block Connector. The hub was bus-powered by

the upstream USB port, t h i s terminal block connector is to

add power to ensure enough power for the 7 downstream

ports.

3. Connecting USB Host cable: Thehostcableiseither a

standard A-to-B USB2.0 cable or a screw-locktypeA-to-B

cable. Please connect the type-Aendconnector of the

cabletoyour upstream USBport,then connectthetype-B

3. Hardware Installation

-+7~24V

-GND

7-PortUSB2.0MetalHubwithDINRAILMountingKit

end connector to this hub. Since the USB hub is

plug-and-play, you don’t have to turn off your host

computer when installing the hub.

Note: In some cases, you will see an error message said

that the USB Hub caused the USB bus power over the current limit,

please ignore this message since the hub is hot plug and its power

capacitor will cause a very short period of current. It will NOT affect

your USB function.

4. Connect the USB devices to the downstream ports of this

hub.

5. Mount your hub on the wall or DIN RAIL if required.

7-Port USB2.0 Metal Hub with DIN RAIL Mounting Kit

To check the USB hub installation in Windows device manager,

please follow the following steps:

1. Click Start

2. Click Control Panel

3. Click System

4. Click Device Manager button

5. Double click Universal Serial Bus Controller

6. Double click Generic USB Hub, the message will show that

this device is working properly.

Operating temp.: 0 to 558C (32 to 1318F)

Operating humidity: 5 to 95% RH

Dimensions (LxWxH): 5.23”(L)x2.42”(W)x1.43”(H)

(13.30x6.15x3.63 cm)

5. Environmental Specifications

4. Checking the Hub Installation

Here is your USB2.0 Hub

7-PortUSB2.0MetalHubwithDINRAILMountingKit

7-Port USB2.0 Metal Hub with DIN RAIL Mounting Kit

Autres manuels pour USBG-7DU2

Table des matières

Autres manuels CoolGear Changer

CoolGear

CoolGear CG-7PU31HB Manuel utilisateur

CoolGear

CoolGear CG-16PU31H Manuel utilisateur

CoolGear

CoolGear CG-7PU3MGD Manuel utilisateur

CoolGear

CoolGear CG-1600i-RM Manuel utilisateur

CoolGear

CoolGear USBG3-3X4M Manuel utilisateur

CoolGear

CoolGear USB3- 16U1 Manuel utilisateur

CoolGear

CoolGear USBG-4U2ML Manuel utilisateur

CoolGear

CoolGear CG-G1M4PHT Manuel utilisateur

CoolGear

CoolGear CG-4P31CHUB Manuel utilisateur

CoolGear

CoolGear USBG-12U2ML Manuel utilisateur

CoolGear

CoolGear USBG-7DU2i Manuel utilisateur

CoolGear

CoolGear USBG-10XU1 Manuel utilisateur

CoolGear

CoolGear USBBG-12U2ML Manuel utilisateur

CoolGear

CoolGear USBG-3X4M Manuel utilisateur

CoolGear

CoolGear USBNET-400i Manuel utilisateur

CoolGear

CoolGear USBG-12U2ML Manuel utilisateur

CoolGear

CoolGear USBG-4U3ML Manuel utilisateur

CoolGear

CoolGear USBG-7DU2 Manuel utilisateur

CoolGear

CoolGear CG-G17PHHT Manuel utilisateur

CoolGear

CoolGear CG-10U2AML Manuel utilisateur

CoolGear

CoolGear USBG-7DU2S Manuel utilisateur

CoolGear

CoolGear USB3-16U1 Manuel utilisateur

CoolGear

CoolGear USBG-4SU2MLA Manuel utilisateur

CoolGear

CoolGear USBG-4U2ML Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur